This tutorial contains the different types of weed rolling methods and techniques. So sit back, relax and smoke up.

Dedicated to all real niccaz and babes out dere.


THE U-BOAT JOINT

Thing You’ll Need

Marijuana
Rolling Papers

Instructions On How To Roll A Boat Joint

1. First take your marijuana and break it up into smaller
pieces, while removing any stems or seeds you may
find.

2. Now take a piece of rolling paper and notice that most
brands are folded down the middle already, take and
fold the bottom into the middle and crease. This makes
it easier to the marijuana to sit.

3. Hold the paper horizontally in your hand and pour your
broken up marijuana into the middle of the newly
creased area.

4. Using your index fingers your want to flatten the
marijuana out along the entire length of the paper
maintaining the shape of a joint (round)

5. Bring in the center of the paper with your thumbs and
use your index fingers to rolling the ends.

6. Repeat until you are almost at the glue and then lightly
lick the glue strip.

7. Fold in the glue pressing it firmly into the the body of
the joint ensuring a firm stick.

8. You have your first U-boat

....Call him the ganja farmer....

Things You’ll Need

Rolling Paper’s

Notecard/Index Card

Thread/Rope/ Rubber Band

Instructions On How To Roll A Tulip Joint

1. Roll the index card into a tube about the width of a pen.
Using a couple paper’s seal the tube so it keeps it
shape.

2. Take sheets of rolling paper and attach them together.
Attach the paper’s one on top of each other to make a
square.

3. Fold the lower right hand corner of your new rolling
square up into the upper left hand corner, just below
the glue.

4. Lick the glue strip and fold it over onto itself, now open
the cone.

5. Fill the cone with your mix gently packing it down as
you go, make sure to keep it even.

6. Now stick the stem into the center of the pocket of
marijuana you just created and pull the sides of the
rolling paper around the stem.

7. Using your thread or rubber band secure the tulip to the
stem as tightly as you can.

Things You’ll Need

Rolling Papers

Safety Pin

Marijuana

Instructions On How To Roll A Cross Joint

1. First thing you need to do is roll yourself an extra thick
joint with any type of marijuana you choose.

2. Next you are going to roll another joint, thinner then the
first, but close off both ends.

3. Take your safety pin and begin to drill a small hole into
the upper half of the larger joint about the width of the
smaller joint.

4. Then cut a small hole direct through the center of the
thinner joint in the same way.

5. Slowly slide and twist the the smaller joint into the
larger one’s hole and and turn it so that it’s hole is aimed
toward the larger joints roach.

6. Carefully seal the connecting joints with gummed strips
of rolling paper. Make sure it’s airtight.

Things You’ll Need

3 pieces of rolling papers

Marijuana

Instructions On How To Roll A Fatty Joint

1. Remove three pieces of rolling paper from your pack.

2. Fold one in half with the glue facing out, lick the glue.

3. Now stick the other two papers together side by side
slightly overlapping with the folded paper in between
them.

4. After 3 seconds, remove the folded piece from in
between the other two pieces and press them back
together.

5. Apply a generous amount of your mixer into the center
of the paper and smooth out length wise with your
finger.

6. Starting in the center begin to fold the bottom edge over
the mixer into itself with your index fingers.

7. Continue this motion until your finger are at the corners
of the joint.

8. Carefully reposition your index finger on the center of
the joint and begin to roll it over once again, and
continue to the outside as before.

9. Lick the glue and use your lips to gently press the glue
down onto the joint.

10. FATTY BO BATTY!!

Things You Need

Rolling Papers

Marijuana

Instructions On How To Roll A Diamond
Joint

1. First you need to roll a , longer then normal,joint with a
firm and secure roach

2. Very carefully cut the joint into two smaller joints using
something sharp.

3. Now roll two more joints, a little bit thinner then the
first, without roaches. When rolling these joints put less
herb in their centers of them. (So you can bend them
later on)

4. Trim away any excess paper from the ends of these to
joints.

5. Tear the gummed strips off of ten pieces of rolling
paper and discard the rest of the papers.

6. Now use the extra gum strips to attach one of the
shorter joints to the two long joints in a triangle shape.

7. Make sure this is air tight!

8. Very carefully bend the two joints at their centers so
that will form the diamond shape.

9. Now bandage the other short joint to the free ends of
these longer joints the same way you did in step 6.


http://www.wearebaked.com/how-to-roll/how-to-roll-a-joint/

Your welcome to share your kushing experiences.

Of all places, i still consider Shitta weed to be the best. I swear

learning S.BAN

Wow.... what a tutorial.

Rasbajan:
Your welcome to share your kushing experiences.

Of all places, i still consider Shitta weed to be the best. I swear

try kwale weed or uselu membrane in Benin