Welcome, Guest: Register On Nairaland / LOGIN! / Trending / Recent / NewStats: 3,148,520 members, 7,801,400 topics. Date: Thursday, 18 April 2024 at 02:45 PM |
Nairaland Forum / Science/Technology / How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations (484 Views)
How Rc Plane Work (v-man) / How To Rewind Brushless Motor (v-man Innovation) / See Power Innovations That Can Solve The Electricity Supply Problem In Nigeria (2) (3) (4)
How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations by victorigwe: 5:58pm On May 23, 2019 |
Is all about science. |
Re: How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations by victorigwe: 6:03pm On May 23, 2019 |
hello good people, this is an important massage from Mr. Antone alene , he is a very good friend of mine in the US, who help in shearing knowledge to the young engineers, here is base on rc aerodinamics, how to make foam Stiffen and strong, like hobbies in the usa... |
Re: How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations by victorigwe: 6:06pm On May 23, 2019 |
Here is additional recommendation:
-Since that foam is so crumbly & weak, try
slicing it in 1/2 AGAIN(..those panels you
use for the fuselage sides-->cut them 1/2 as
thick again..)--so they are only 1/4 thick. Of
course it will be immediately weaker, but
then cover with wet paper + glue...and
press these thinned foam panels BACK
together again...creating a laminate
sandwich with paper in between. Allow to
dry in a warm place beneath weighted
books.
Your strength/integrity of the foam will
increase tremendously.
If you have a hot wire cutter table..that you
can slide whole sheets of foam
beneath...you can repeat this with even
thinner foam sliced sheets. The MORE layers
of paper you can laminate in-between, the
STRONGER & more durable your foam
panels--similar to Flite Test DTFB.
There will be a weight increase, but not
much or crazy--far less than adding packing
tape for the amount of strength you gain in
return.
-As an alternative to sandwiching paper, if
you can get the palm branches, reeds and
dried leaves--shave them very thin &
uniform...into sticks & rods as fine as you
can & long as you can neatly. Make slices
along the full length of your foam panels,
about 1/2-way deep into your styrofoam--
then insert these sticks, rods & flat leafs full
length with white glue.
They will act as 'rebar'--just like inside
poured concrete. Apply a paper covering on
the outside and you should still have
valuable strength//stiffness gains with little
weight penalty.
-If you can obtain tan-colored 'wood glue'
instead of white glue--use that! Much better
for stiff construction. To make your white
glue somewhat stiffer when it dries, there
are 2 additives which will help.
a ) See if you can get the dry, white
powdered clothing starch...the kind you mix
w/cold water & spray on a cotton dress
shirt--to make ironed creases and stiff
collars for church wear. It will add a slight
element of this same stiff character to your
papers and things assembled from white
glue.
b)If you can obtain a bag of saw dust...or
use some saw, drill or grinding tool to make
your own out of scrap wood---create a
large amount enough to fill a plastic
shopping bag at least 1/2 full. Then....obtain
a fine, mesh screen--either mosquito
netting or window insect mesh will do. OR--
the type of metal 'flour sifter' that women
use when baking bread & pastries...to
shake their flour through BEFORE mixing
with eggs, oil, etc...
The flour granules will sort out thru the
fine wire, yielding ONLY the 'finest' part and
the lumps & grit behind.
Well--do the SAME with your sawdust;
keeping the finest dust granules behind in
your bag or jar!
Mix this very fine sifted sawdust with your
water-thinned white glue that you apply to
ALL your foam panels while you are adding
paper to its surfaces.
Your completed foam panels will AGAIN be
far stiffer and have a harder surface. This
white glue + fine sawdust can be applied as
reinforcement 'putty/paste' in other areas
of your construction.
These steps are additional 'preparation
work' and take some time, but if you pre-
treat many foam panels with these methods
ahead of time, your supply of 'build ready
material' will be available for each new
project or repair |
Re: How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations by victorigwe: 8:56pm On May 23, 2019 |
Re: How To Make Your Syterofoam Strong For Rc Plane, V-man Innovations by victorigwe: 12:32am On Aug 22, 2019 |
this will explain the more,. make out worm water not too hot, mix it with topbound or an water gum, apply same gum on the form, after 15minutes on water, bring it out and rap the foam, and stiffen the fragile foam, watch the video. https://www.youtube.com/watch?v=XtmWk1f9X8M |
(1) (Reply)
Young Nigerian Inventor Produced A Machine From Bicycle And Grinding Engine / I Urgently Need This Camera: Lifecam HD 3000 USB Webcam / The Benefits Of MTN Xtravalue
(Go Up)
Sections: politics (1) business autos (1) jobs (1) career education (1) romance computers phones travel sports fashion health religion celebs tv-movies music-radio literature webmasters programming techmarket Links: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) Nairaland - Copyright © 2005 - 2024 Oluwaseun Osewa. All rights reserved. See How To Advertise. 28 |