@princejude ,Hello sir pls how much is Pickit2 now how can i get it in ondo

princejude:
Arduino Workshop LIVE in Enugu 12th June. Don't miss it...

@princejude ,Hello sir pls how much is Pickit2 now how can i get it in ondo

ceetowl:
@princejude ,Hello sir pls how much is Pickit2 now how can i get it in ondo

Pickit3 is N7000 plus N2000 shipment fee. The pickit2 I have is on-board a development kit named Pic Kit With Programmer. Search for it in my online shop.

www.jutronix.com/shop

September Arrivals

ISD1820 Voice Recording Module
TDA2030 Amplifier Module
W5100 Ethernet Shield
9 Pin 10k A09-103 Resistor pack
8 Channel Relay module
microSD Card Module
CP2102 USB-TO-TTL
L7805CV
ST Link V2
STM32F103C8T6 ARM Minimum Board
Electronic Door Lock
MB-102 (830 Point) Bread Board
20cm Dupont male – female
20cm Dupont male – male
GPS Receiver
MG995 Metal Gear Servo
MG90S Metal Gear Mini Servo
SG90 Mini Servo
Stepper Motor with ULN2003 motor driver board
LM35 Temperature Sensor
HLK-PM01 AC-DC 220V to 5V mini power supply
RFID NFC PN532 Shield
MLX90614 Contactless Temperature Sensor Module
DHT11 Temperature And Relative Humidity Sensor Module
Servo Pan/Tilt Anti-Vibration Camera Mount
Kinsten Positive Acting Presensitized Single-sided PCB PP1015 (10×15)cm x 1.6mm
Kinsten Positive Acting Presensitized Double-sided PCB PP1015 (10×15)cm x 1.6mm
FR4 PCB Single Side Copper Clad Board. 70 x 100 x 1.5 mm
FR4 PCB Double-Side Copper Clad Board, 150 * 100 * 1.6 mm
1W Zener diode 3.3v -30V
DIY KIT GSM GPRS 900 – 1800 MHz Short Message Service SMS module
Robotic Arm
MQ-137 Ammonia Gas Sensor
PH Level Sensor Module

How much are these your servos; MG995 Metal Gear Servo, MG90S Metal Gear Mini Servo, and SG90 Mini Servo?

Pakingzzz:
How much are these your servos;
MG995 Metal Gear Servo,
MG90S Metal Gear Mini Servo, and
SG90 Mini Servo?

MG995 = N3500, MG90S = N2000, SG90 = N1000

Hello everyone. Have a quick question.
I'm quite proficient working with microcontrollers but I'm mainly familiar mikroc pro. One problem I once encountered with one of the works I did was that the demo version has a limit of only 2k program words and my code exceeded that by much. This will be a major problem if I'm to do more complex works. This has made me to start considering trying out other compilers (ccs especially on my mind). What advice would you have for me?

AideeSheks:
Hello everyone. Have a quick question.
I'm quite proficient working with microcontrollers but I'm mainly familiar mikroc pro. One problem I once encountered with one of the works I did was that the demo version has a limit of only 2k program words and my code exceeded that by much. This will be a major problem if I'm to do more complex works. This has made me to start considering trying out other compilers (ccs especially on my mind). What advice would you have for me?

Trying other compilers will not solve the issue of 2k program limit because most of the free version of compilers have their own limitations.

I will suggest three options for you:

1. Manage the free version of the compiler
2. Buy the full version
3. _{google for the crack}

AideeSheks:
Hello everyone. Have a quick question.
I'm quite proficient working with microcontrollers but I'm mainly familiar mikroc pro. One problem I once encountered with one of the works I did was that the demo version has a limit of only 2k program words and my code exceeded that by much. This will be a major problem if I'm to do more complex works. This has made me to start considering trying out other compilers (ccs especially on my mind). What advice would you have for me?

download the cracked version from 4shared.com

davechika:

its simple,i guess ur door already have actuators for opening and closing,atmel 8051 family of microcontroller is a good start.
burning the code to the chip is as simple as ABCD.u can get these chino (china) universal programmer like topwin (i use it mostly for my codes) etc.rememba u gat to get a microcontroller c complier (specifically for microcontroller eg keil u vision) its different from ur normal c compiler.
you need simulation sofwares also like protues to simulate ur code before burning onto the chip.
if u gat more question pls do ask.

Pls this is my number just flash me I will call u back. Thank

08161377748

Mark Zuckerberg facebook (founder) make speech concerning programming.

https://www.youtube.com/watch?v=nTMubSRm5MY

check my posts on micro-controller programming,you might find something useful and inspiring,...i am a versatile professional software/embedded system engineer.here is of my designs

tunasha:
check my posts on micro-controller programming,you might find something useful and inspiring,...i am a versatile professional software/embedded system engineer.here is of my designs

Wellcome on-board

I am setting up an IoT incubator. Engineers with experience in embedded systems, Proteus circuit design and simulation, circuit design etc are welcome to apply for positions. We will also be taking on IoT entrepreneurs.

okwuiagada:
I am setting up an IoT incubator. Engineers with experience in embedded systems, Proteus circuit design and simulation, circuit design etc are welcome to apply for positions. We will also be taking on IoT entrepreneurs.

hmm

Following

On board.

VoidLoop:
On board.

DoWhile... on board the train ?

princejude:

DoWhile... on board the train ?

If..else.. Board the train

VoidLoop:


If..else.. Board the train

Switch...case: let the train no leave you

princejude:

Switch...case: let the train no leave you

Do run the train, while you're alive.

hoodboi:
Pls are there any embedded programmers in the house who have worked with micro controllers very well. I need help on a project

Embedded System