₦airaland Forum

#DS3231 #RTC #PLC #ArduinoPLC #Outseal #Bluetooth #HC05

Outseal Arduino PLC was programmed to read the DS3231 Real-Time Clock module and display accurate dates and times on the HMI Modbus App with the HC05 Bluetooth module.
The TMatch and DMatch instructions in Outseal Studio allow set date and time to be compared with the actual date & time which then initiates the enabling and disabling of an output device.


https://www.youtube.com/watch?v=qJSjO1ehFyg

#DT06 #Modbus #PLC #ArduinoPLC #Outseal #WIFI

The DT-06 WIFI module has the same shape and pinout as the HC-06 Bluetooth module which allows for easy replacement with almost no modification. It is connected to the Outseal Arduino PLC to provide a wireless interface to the HMI Modus Android Phone App. A monitoring and control interface created in the HMI Modbus App from video #15, reads and sends data to the Outseal PLC program. The PLC is programmed to read the temperature value of an LM35 temperature sensor and turn On or Off an indicator lamp depending on the low and high setpoint. Lamp turn On and Off can also be done directly from the panel. The required setpoints can also be adjusted from the HMI Modbus App.


https://www.youtube.com/watch?v=Y6KKRT7RS3A

#HC05 #Modbus #PLC #ArduinoPLC #Outseal #Bluetooth

The HC-05 Bluetooth module is connected to the Outseal Arduino PLC to provide a wireless interface to the HMI Modus Android Phone App. A monitoring and control interface is created in the HMI Modbus App to read and send data to the Outseal PLC program. The PLC is programmed to read the temperature value of an LM35 temperature sensor and turn On or Off an indicator lamp depending on the low and high setpoint. Lamp turn On and Off can also be done directly from the panel. The required setpoints can also be adjusted from the HMI Modbus App.


https://www.youtube.com/watch?v=hUthE8Fh7O0

#OP320 #Modbus #PLC #ArduinoPLC #Outseal #Xinje

The Outseal Arduino PLC was interfaced to an OP320 HMI Operator Panel with a TTL to RS485 Converter Module for industrial Modbus RTU/Serial communication up to a distance of 1 km. The Operator panel is programmed with the OP20 V8.0Q Editor Software. The Outseal PLC was programmed to read the temperature value of an LM35 temperature sensor, and turn On or Off an indicator lamp depending on the low and high setpoint. Lamp turn On and Off can also be done directly from the panel. The required setpoints can also be adjusted from the OP320 operator Panel.


https://www.youtube.com/watch?v=iC2vYqDj54s

#VTScada #Modbus #PLC #ArduinoPLC #Outseal
The Outseal Arduino PLC was interfaced to a VTScada system (free licence) with a TTL to RS485 Converter Module and a USB to RS485 Converter Module for industrial Modbus RTU/Serial communication up to a distance of 1 km. The Outseal PLC was programmed to read the temperature value of an LM35 temperature sensor, and turn On or Off an indicator lamp depending on the low and high setpoint. The raw value and scaled value of the temperature reading as well as the setpoints were displayed on the VTScada user interface. The required setpoints can also be adjusted from the VTScada interface.


https://www.youtube.com/watch?v=faVKkdhgEXE

All Outseal Arduino PLCs are Modbus Clients (Slave) by default. The Outseal Arduino PLC Relays, Switches, Memory Bits, Analog inputs and Holding Registers are mapped to the required Modbus Address and are accessed by a Modbus Server (Server). The VTScada Light has free 50 tags licence. VTScada is the Modbus server where it performed Modbus discrete output coils (relays) read, discrete input contacts (switches) read and discrete output coils (memory bits) read/write on indicators turn on sequences from video #10 on this series.


https://www.youtube.com/watch?v=apYfPOtISKI

The Outseal Arduino PLC is programmed and scaled to reading the analog values of a potentiometer, LM35 temperature sensor and a 4-20mA temperature transmitter through a 4-20mA current to voltage converter module. the value of the potentiometer operates for relay outputs of the PLC. The converter module zero and span calibration was carried out before being connected to a temperature controller circuit.


https://www.youtube.com/watch?v=qxcVWX-BqUo

The compare instructions in Outseal Studio are equal, not equal, greater than or equal, greater than, less than or equal, less than, limit, Tmatch and Dmatch. They are used to compare two or more variables or constants to determine a required action. This video demonstrates how to use them to sequentially turn on indicator lamps.


https://www.youtube.com/watch?v=nJiiKCTnZ_Q

The control program for the Outseal Studio water tank simulation from video #5 was improved with a timer and a counter to create a sequence of self-starting and stopping of the pump once initiated.


https://www.youtube.com/watch?v=3rMAXLh_VHs

This video demonstrates the use of the Counter Up and the Count Down instructions with an Arduino Nano Outseal Programmable Logic Controller, push-button switches and indicator lamps. They can be used together to operate a single variable to either count up or count down.


https://www.youtube.com/watch?v=DNm4d7PnlVs

Using Retriggerable One-Shot Timer On and Software Pulse Width Modulation

https://www.youtube.com/watch?v=UMZlqwXPTIA

Programming delay timers


https://www.youtube.com/watch?v=dskZPJIwc2Q

Outseal Studio has in its simulation window a want tank with a pump, level switches, ON/OFF button and indicators. Ladder logic is put up to control the pump to fill up the water tank both with manual control and automatic control.


https://www.youtube.com/watch?v=Cby_XrZTpWY

The latch(set), unlatch(reset), flip on rising and the flip on falling instructions are output instructions that are explained in this video using the Outseal Studio simulation of a ladder diagram and online mode demonstration with the Arduino Nano PLC circuit connection.



https://www.youtube.com/watch?v=eGGqIujq3Ys

How to Interface Industrial Sensors with Arduino Nano


https://www.youtube.com/watch?v=leZOo8hbLpo

Contact are inputs instructions in a ladder diagram. While relays or coils are output instructions. The normally open contact, normally close contact, normal coil and inverse coil are explained in this video using the Outseal Studio simulation of a ladder diagram and online mode demonstration with the Arduino Nano PLC circuit connection.


https://www.youtube.com/watch?v=q6HpgXXAgzA

Arduino Nano wirelessly connects to a mobile phone app - Roboremo with DT-06 WiFi module.


https://www.youtube.com/watch?v=g__zlR6ar48

Studio Overview is the second video in the series of How to Program Outseal Arduino PLC.
It is an overview of Outseal Studio that includes hardware selections and settings, a description of some program elements, data variables and selection. How the different features of the studio are used to write and simulate a ladder diagram.


https://www.youtube.com/watch?v=YjbdqDTThmM

How to Program Outseal Arduino PLC - Getting Started is the first tutorial in a series that will introduce you to the programming of Outseal PLC with a ladder diagram. Outseal PLC is open-source hardware that is programmed with ladder logic in Outseal studio. Arduino Nano is used with other modules and components in the practical demonstration of the different instruction blocks.


https://www.youtube.com/watch?v=FRJ3o5aj9EA

Arduino Nano wirelessly connects to a mobile phone app - Roboremo with ESP-01 WiFi module.


https://www.youtube.com/watch?v=VHPNcWJ23aw

Real-Time Clock timer base Start-Stop Controller

https://www.youtube.com/watch?v=CFwJpHDYJDc

Program Arduino Boards without the IDE using AVRDUDESS


https://www.youtube.com/watch?v=rIM_MqW729U

You need Arduino Mega2560 when you are running out of inputs/outputs and memory in your project.


https://www.youtube.com/watch?v=jRJ-DItW3FE

I am sure you can get it from Jumia.com

LM35 Temperature Controller and DS3231 Real-Time Clock display on an I2C LCD


https://www.youtube.com/watch?v=Tr6mZwcGyh8

A new series on building your own PLC with Arduino nano and programming it with LDmicro has begun.

https://youtube.com/playlist?list=PLjkzNLFcHTFDEdMaHeJVP2nJ7NE33N00K

Navigate the menu structure of the Temperature Controller with an Incremental Rotary Encoder


https://www.youtube.com/watch?v=gz8GNsL21nA

Build a Global Positioning System (GPS) Alarm Clock for Accurate timekeeping.

https://www.youtube.com/watch?v=RxUBoHtY6t8

Here are some tricks in editing ladder logic


https://www.youtube.com/watch?v=zKEY-NVEBhQ

telim:
Really like this thread my elder bro son will learn alot from you

Sure! The software & knowledge is open source.

Now you can also display temperature and set alarm function in addition to displaying the date and time all organized by a menu function.


https://www.youtube.com/watch?v=vbq3zlObp7c

Real-Time Clock with PIC16F876 Microcontroller, demonstration of C mode programming in LDmicro.


https://www.youtube.com/watch?v=55Bk0BAX8P8