₦airaland Forum

fuckboys:
A battery with 1.2kwh, 100ah. How bad is this battery?

Haven't even hit 50ah yet and it's at 80% dod

favouredbymercy:
Guyyyy i said i would chat you today about this, and you are already experiencing what i planned to talk to you about. Your central stabilizer is the cause. PERIOD.... Stabilizers are crazy for leakages. I know from experience. Only 2 solutions: 1. Earth your stabilizer, not to your main DB, since it is feeding the DB or 2. Tap your inverter AC input upstream to the stabilizer i.e before the stabilizer, where the stabilizer is getting its own input from.

Hope you understand?

fuckboys:
i totally understand you chief but out nepa light here is terrible and always fluctuating, I don't want it damaging my inverter so I won't bypass the central stabilizer.

What i plan doing is putting a breaker between the battery and inverter, so I'll just switch of the breaker whenever I wanna touch or access the battery since the shock is only on the battery.

maklelemakukula:
How many panels do you have. Cant you just add more and leave nepa for good

fuckboys:
i totally understand you chief but out nepa light here is terrible and always fluctuating, I don't want it damaging my inverter so I won't bypass the central stabilizer.

What i plan doing is putting a breaker between the battery and inverter, so I'll just switch of the breaker whenever I wanna touch or access the battery since the shock is only on the battery.

fuckboys:
omo you're right, they just took light and the shocking have stopped.

It's leaking from the mains. How do I trace this?

spartacus11:
Please house were can i get original jinko panel

FEGEITOK:
How much power does this shunt consume?

Does anyone know?

mctfopt:
Try running an independent earth. When you've done this, remove the "follow come earth" which most times ain't effective.

Ferdiwar:
If you're living in a rented apartment with a central earthing, disconnect it and install yours it will stop.

I had same experience and after I did that (joint 2 4ft earth rods together and drove it to the ground and linked it to my connection) it stopped.

Jonescosmos advised me then to run an independent earthing for my setup and it's been working great since then.

I later found out that an electrician looped my neighbors neutral to the earth terminal in the DB.

bbally:
Hello, what is your review on this firman / itel inverters on inductive loads and surge startup of AC compressor.

Do you have any recommendations on a 4kw/5kw hybrid inverter on 24volts?

fuckboys:
what it consumes is very insignificant. 0.45w with the screen on.

Dam5reey1:
Don't Buy Lead acid in 2025 abeg..
We just replaced a Lead acid with this

It only managed 52,369AH, approximately 261 Cycles less than 2 years e don degrade to 10% capacity

Now we have installed 3.6kwh with 1.5kva Hybrid

Dam5reey1:
Don't Buy Lead acid in 2025 abeg..
We just replaced a Lead acid with this

It only managed 52,369AH, approximately 261 Cycles less than 2 years e don degrade to 10% capacity

Now we have installed 3.6kwh with 1.5kva Hybrid

Dam5reey1:
Don't Buy Lead acid in 2025 abeg..
We just replaced a Lead acid with this

It only managed 52,369AH, approximately 261 Cycles less than 2 years e don degrade to 10% capacity

Now we have installed 3.6kwh with 1.5kva Hybrid

Dam5reey1:
Don't Buy Lead acid in 2025 abeg..
We just replaced a Lead acid with this

It only managed 52,369AH, approximately 261 Cycles less than 2 years e don degrade to 10% capacity

Now we have installed 3.6kwh with 1.5kva Hybrid

fuckboys:
i panels are well sized, total of 1680w. My 3.6kwh battery gets filled up before 11am

Oshomo12:
Why do you still charge with phcn then? Make me understand. PhCN is your weak link in the system. If you must use Nepa, get a transfer switch. Use nepa when there is light, don't charge your battery with it.

I don't like nepa with inverter system

fuckboys:
i totally understand you chief but out nepa light here is terrible and always fluctuating, I don't want it damaging my inverter so I won't bypass the central stabilizer.

What i plan doing is putting a breaker between the battery and inverter, so I'll just switch of the breaker whenever I wanna touch or access the battery since the shock is only on the battery.

Oshomo12:
Why do you still charge with phcn then? Make me understand. PhCN is your weak link in the system. If you must use Nepa, get a transfer switch. Use nepa when there is light, don't charge your battery with it.

I don't like nepa with inverter system

fuckboys:
why preset the battery at 280ah when it can pull 290ah?

mctfopt:
I have people who swore that LA is cheaper. I no dey convince anyone. They'll learn the hard way .

Oshomo12:
Why do you still charge with phcn then? Make me understand. PhCN is your weak link in the system. If you must use Nepa, get a transfer switch. Use nepa when there is light, don't charge your battery with it.

I don't like nepa with inverter system

fuckboys:
i never really charge with nepa or gen, I just have it installed in just for the convenience of it.

fuckboys:
i never really charge with nepa or gen, I just have it installed in just for the convenience of it.

Oshomo12:
Kindly disconnect it, if I must charge and solar is not enough, I use gen. Drama too much with Nepa

Though you need to rectify the earthing issue. The but is: na landlord house o

CuteMaro:
How's your battery performing Chief?

Iinnov8:
My empathies about your situation, bro. This is definitely not the right time to make any mistake in choice of renewable energy components.
I have a KL110F Coulomb meter with Bluetooth app function that does an excellent job showing your charging and discharge values. I also have a crude, but detailed video showing you how to connect it

Price: 47,000

fuckboys:
it's close to 3 weeks now of active usage and I've never drained the battery no matter how hard I try.

A Fridge and a 43" smart TV with 2 ceiling fans all night has refused to drain the battery. It's very good.