₦airaland Forum

kingreign:
They’re not necessarily meant for older engines. They’re meant for cars which have the known defect of excessive oil burn due to defective PCV or breather valve designs. They’re meant to trap oils in the valve top which the PCV loses.

It’s beneficial to not only GDI but MPI engines too especially those with badly designed PCV and headers which can trap excessive air and vapors.

Omo, you studied mechanical engineering? The above analysis doesn’t sound like road side mech to me. No mind me sha.

Does it stop smoking by bad engines ?

Conner44:
You can create one by yourself. All you need is

A length of oil pipe/hose (the same type and size with the one running from your pcv to valve cover)

Two small pipes of similar diameter with your pcv hose fitting

Weld the pipes into a small container (vacuumed) with one sticking further into the container than the other (one pipe should be shallow and one should run half way deep)

Iron sponge (the type used in washing pots) that will be wrapped around the deeper running iron pipe inside the catch can

And hooks/hangers or a way to mount the can somewhere convenient in your engine bay (as far away from any major heat source as possible)

Also make sure the can you choose has a screw cover or you can weld a small tap/valve for emptying the contents out when it’s caught some oil.

I e done it before. I used one of all those aluminum water bottles that office workers usually carry around. On an EOD engine it caught some oil over the course of an oci and I’d recommend it to keep your valve train and intake manifold sludge free.

Can you snap a pic of one you made?
Thanks

MASTAkiLLAh:
I just watched a Scotty Kilmer video talking about this thing and how good they are for cars with older engines and also very good for cars with GDi engines.
What are your experiences ? Let's learn

Cc Egunmogaji2, Gazzuzz, Kingreign, Femtopford, diportivo et al

Nigerian consumer experience is in focus here

Most people in Nigeria are more concerned about price of petrol now...I doubt ifbyou would find many Nigerians who give a damn about installing this thing in their cars

Just do a pcv delete and you'll be good to go

kingreign:
They’re not necessarily meant for older engines. They’re meant for cars which have the known defect of excessive oil burn due to defective PCV or breather valve designs. They’re meant to trap oils in the valve top which the PCV loses.

It’s beneficial to not only GDI but MPI engines too especially those with badly designed PCV and headers which can trap excessive air and vapors.

DamnNigga!!
I hope you didn't change Our PVC to PCV ??

frowland:
Omo, you studied mechanical engineering? The above analysis doesn’t sound like road side mech to me. No mind me sha.

I’m an Environmentalist (MSc.) by qualification.
By profession, I’m an Engineer (automobiles).

BigDawsNet:
Which motor vehicle was prominently featured in the Bible?





Honda, because the apostles were all in one Accord.

Conner44:
You can create one by yourself. All you need is

A length of oil pipe/hose (the same type and size with the one running from your pcv to valve cover)

Two small pipes of similar diameter with your pcv hose fitting

Weld the pipes into a small container (vacuumed) with one sticking further into the container than the other (one pipe should be shallow and one should run half way deep)

Iron sponge (the type used in washing pots) that will be wrapped around the deeper running iron pipe inside the catch can

And hooks/hangers or a way to mount the can somewhere convenient in your engine bay (as far away from any major heat source as possible)

Also make sure the can you choose has a screw cover or you can weld a small tap/valve for emptying the contents out when it’s caught some oil.

I e done it before. I used one of all those aluminum water bottles that office workers usually carry around. On an EOD engine it caught some oil over the course of an oci and I’d recommend it to keep your valve train and intake manifold sludge free.

Chief please post a photo of the EOD engine that you installed the can for us to see

Never

Summary?

Buy a well built car

GREAT men dey here

kingreign:
I’m an Environmentalist (MSc.) by qualification.
By profession, I’m an Engineer (automobiles).

Morning

I have a friend who wants to love-vendor the interior of his IS350 i dont know if you do or know anyone who does preferred location Abuja and Lagos
Thanks

salamudeen:
Morning

I have a friend who wants to love-vendor the interior of his IS350 i dont know if you do or know anyone who does preferred location Abuja and Lagos
Thanks

I do,
Pls, contact me on 07034581213 (calls and WhatsApp)

Please boss I sent you dm about your comment on one thread like that about foodstuff exportation

SeyiJay:

foxxydude:
Chief please post a photo of the EOD engine that you installed the can for us to see

Sorry I’m not using that particular vehicle anymore if not I’d have posted one. You can google it to k is how it looks.

@Perfectbeing