In modern society, stainless steel bridges are commonly used when installing bridges.

Through the use of stainless steel cable tray vendors bridge, this can effectively reduce the installation cost, at the same time can effectively prolong the life of the bridge.

However, when installing the stainless steel bridge, we also need to install it correctly according to the prescribed installation method.

So, what are the setting methods of stainless steel bridge?
Next, the editor will give you a brief introduction.

1. The installation of stainless steel bridge at the top of the cabinet, due to the particularity of the ceiling structure and the floor is too high, so usually choose the top of the cabinet for installation.
As a result, the bridging can be effectively set up while avoiding the problem of ceiling being destroyed.
When installing the top cabinet, it can be bolted and fixed without opening at the top of the cabinet.

2. When installing stainless steel bridge frame on ceiling, ceiling installation mode can also be used.
However, in such an implementation, it is recommended that the specific span be calculated according to the actual load.

3. When installing the stainless steel bridge, we usually use the ground support to install the stainless steel bridge, which usually installs not only the cable bridge but also the outdoor base station.
That is to say, when installing a stainless steel cable tray vendors, good results can be obtained as long as it is set up in the correct way.
If the setting method is wrong, it will affect the overall use of the bridge, and unnecessary failures will occur, so please pay attention to the installation.

Ned-Tech Cable Tray Ltd - We manufacturer wholesaler and supplier of cable tray, cable ladder, wire mesh etc
We supply to all countries.

Contact Us Now!
+2348061295622

Website: https://nedtray.com

Facebook page: https://facebook.com/nedtechng

Address: DD72 up alaba international market ojo Lagos, Nigeria

monastik:
In modern society, stainless steel bridges are commonly used when installing bridges.

Through the use of stainless steel cable tray vendors bridge, this can effectively reduce the installation cost, at the same time can effectively prolong the life of the bridge.

However, when installing the stainless steel bridge, we also need to install it correctly according to the prescribed installation method.

So, what are the setting methods of stainless steel bridge?
Next, the editor will give you a brief introduction.

1. The installation of stainless steel bridge at the top of the cabinet, due to the particularity of the ceiling structure and the floor is too high, so usually choose the top of the cabinet for installation.
As a result, the bridging can be effectively set up while avoiding the problem of ceiling being destroyed.
When installing the top cabinet, it can be bolted and fixed without opening at the top of the cabinet.

2. When installing stainless steel bridge frame on ceiling, ceiling installation mode can also be used.
However, in such an implementation, it is recommended that the specific span be calculated according to the actual load.

3. When installing the stainless steel bridge, we usually use the ground support to install the stainless steel bridge, which usually installs not only the cable bridge but also the outdoor base station.
That is to say, when installing a stainless steel cable tray vendors, good results can be obtained as long as it is set up in the correct way.
If the setting method is wrong, it will affect the overall use of the bridge, and unnecessary failures will occur, so please pay attention to the installation.

Ned-Tech Cable Tray Ltd - We manufacturer wholesaler and supplier of cable tray, cable ladder, wire mesh etc
We supply to all countries.

Contact Us Now!
+2348061295622

Website: https://nedtray.com

Facebook page: https://facebook.com/nedtechng

Address: DD72 up alaba international market ojo Lagos, Nigeria

Do you deal on cable Ladders? I have tried reaching you before now.

Please share active email address and phone number. I'll reach out by 8am/8:30am

Kindly contact us through this
CAll/ WhatsApp us: 08061295622
Email: Nedtechnig@gmail.com

sonofthunder:



Do you deal on cable Ladders? I have tried reaching you before now.

Please share active email address and phone number. I'll reach out by 8am/8:30am