₦airaland Forum

MrTony34:
How many amps

Horlaarsco:
which ones available

lykwhoishe:
Good innovation. Question though, how do you know when the battery is full while Charging and when it's low so you turn the system off

MrTony34:
Every inverter or charger nowadays are are intelligent ones when fully charged it cuts off wen battery is down it beeps. U can used battery monitor display to see battery percentage and wen battery is low to turn off

bizz:
For the UPS u talked about

I have
1 tv
1 fridge
2laptops
10 (40w) bulbs ..I can change them to reduce load
1 Decoder
1 home theatre

What size of ups and battery will be ok
How much will it cost

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
2.0 KVA two batteries

LoveThemChubby:
At what cost will the 2.0KVA be?

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Stay safe

ecosystm:
Hi, my inverter is no longer charging my battery (68ah) what could be the cause..? Its always on main

tobtap:
hi mr tony, i own an off-grid farm and i need solar solution for power. the gate house consist of 1 tv,3 light bulbs, one radio/sterio system, decoder, while the fence hold 5 bulbs, plus one 1.5hp pumping machine on d farm. these are the devices i need powered. will be grateful if i can get an estimate from u. cheers

newman0017:
Mr Tony, in one bed apartment wth a samsung 50'' smart tv, standing binatone fan, Dstv explorer, two laptops , a samsung sound bar and ps4 console, 6 energy bulbs with 4 phone chargers... I'll like to know how i can power them all using UPS as Inveter... including all i need to procure prior to installation... Plz be kind as to do the needful at the earliest.. Saludos

MrTony34:
Use 2.2 ups 24v

newman0017:
Thank you sir.. Are you located around PH City?

Baker77:
I heard ps console consumes a lot of power.please put that into consideration.

Baker77:
I heard ps console consumes a lot of power.please put that into consideration.

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7

MrTony34:
Thank you for checking for this new innovation. One thing I want you to know is that ups( uninterrupted power supply) can be used as inverter. It is what Many of us don't have the idea of on what ups can do. apart from it's short time back is known for
It can also be used as inverter for long hours back for load in the house.

Due to its good functionality and features good inverters nowadays have ups selection mode on them you can switch to, to prevent interruption when there is power failure.

UPS has many good features and merit over sachet /pocket inverters.
1. It regulates voltage during fluctuation
2. It provides quality power to load
3. It provides constant voltage
4 it serves as isolation btw mains and load
5 it protects loads from over voltage

How to turn it into inverter for use
Step 1
Carefully locate and Unscrew the ups casing

Step2
Locate the internal connected battery(ies) and disconnect it

Step3
Those two wires of black and red disconnected from the battery(ies) are your positive and negative wire. Cut the tip and Strip the insulation part to be used

Step 5
Get a flex conductor wire of black and red and connect them together. Black to balack and red to red and tape it properly

Step 6
Get any inverter battery of your choice. There are 45ah,75ah, 100ah, 200ah as u can afford. Then connect wires to the battery terminals as indicated red to red and black to black and tighten well

Step 7
Get a battery charger. There are 10a, 30a, 30a, 40a etc. Clip charger crocodile clip on the battery terminal and get the charger power cord plugged on the wall socket to charge the battery with power supply

Step 8
Connect your load at the back of your ups to power your load in the house

Below is a picture of mine. It is what i am using for 2yrs as my inverter

This can save cost of inverter of high cost because It is cheap and affordable. Cost of UPS range from 4k based on capacity u require for your load ( we have ups of 650va, 1.5kva , 1.2kva, 2.0kva, 2.5kva etc)

based on limited capacitt it is Suitable for a room , a room self contained , mini flat and 2bedroom flat.
.
The total of cost of doing this cannot cost you more than 40k, 50k, 60k,70k depending your battery choice of capacity.

HOW TO KNOW THE CAPACITY OF INVERTER/UPS TO CARRY YOUR LOAD
To do that you will need to know first the total load in your house.
Supposed you have:
1. TV 50"....60w
2. Decoder ...25w
3.fan 62".....80w
4. 10 lights each 25w.x10=250w

Total power ...415w
What is the capacity of ups/inverter to carry the load (415w)

We divide the the power load (415w) by
one of the standardd power factor (0.8, 0.7,0.6)
That will give us ...415/0.7 =519va

Therefore we will need 600va or 650va inverter/ups to carry the load.

Note that It is recommended to chose inverter/ ups bigger than the one we need.

HOW TO CALCULATE BATTERY BACKUP TIME.
supposed we have 2 batteries of 200ah/12v and a total load 415w. How many hours will the battery last?

Firstly multiply the battery voltage by the amp hour.
200ah x 12v =2400wh x2 =4800wh
Divide by the load ..4800wh/415w =11hrs.5min

Our backup time will 11hrs.5min but due to the battery can not drop to 0% to prolong the battery lifesspan we will maintain the battery DOD to 50% that will give us 6hrs.


HOE TO CALCULATE INVERTER /UPS CHARGING CURRENT.

Firstly find out the inverter vdc(voltage direct current) which is usually ranges from 12vdc-180vdc above

If my inverter/ ups is a 12v ( that is for one 12v battery) the charging current will be 10% of the battery ah. That is 10/100 =0.1
0.1x 200 = 20a..
Therefore a 12v inverter of any given capacity charging 200ah battery has about 20a charging current.

HOW TO CALCULATE CHARGING TIME
that will be battery ah divide by charging current.

200ah/20a = 10hrs

HOW TO CALCULATE NO OF SOLAR PANEL FOR YOUR BATTERY
suppose you have one 200ah/12v battery and u need solar to charge in the absent of power supply.
It is simple. First know your battery charging current as calculated above 200ah battery charging current is 20a and the battery is 12v.

Power is v x a i.e 12 x 20 =240w

We need 240w solar panel to charge our battery
Note it is recommended we use panel bigger than the one we need in this case we will need 480w panel for proper charging .

Tonytech services
Providing you quality services at all time

Our services include installation, sales and maintenance of all kinds of
1 inverter
2 solar panel
3 cctv
4 electrical
5 solar street light etc

Call an expert today
WhatsApp 0.8.1.8.0.7.2.9.6.1.2.,
Call 0.7.0.1.0.4.2.3.3.3.7