[size=15pt][center]What is a Solar Cell?  [/center]

[b]

A solar cell or photovoltaic cell is a device, which generates electricity directly from visible light by means of the photovoltaic effect. In order to generate useful power, it is necessary to connect a number of cells together to form a solar panel, also known as a photovoltaic module. There is more about the different types of solar cell here. The nominal output voltage of a solar panel is usually 12 Volts, and they may be used singly or wired together into an array. The available light determines the number and size required and the amount of energy required. 

PHOTOVOLTAICS: SOLAR ELECTRICITY AND
SOLAR CELLS IN THEORY AND PRACTICE
The word Photovoltaic is a combination of the Greek word for Light and the name of the physicist Allesandro Volta. It identifies the direct conversion of sunlight into energy by means of solar cells. The conversion process is based on the photoelectric effect discovered by Alexander Bequerel in 1839. The photoelectric effect describes the release of positive and negative charge carriers in a solid state when light strikes its surface.

HOW DOES A SOLAR CELL WORK?
Solar cells are composed of various semiconducting materials. Semiconductors are materials, which become electrically conductive when supplied with light or heat, but which operate as insulators at low temperatures.
Over 95% of all the solar cells produced worldwide are composed of the semiconductor material Silicon (Si). As the second most abundant element in earth`s crust, silicon has the advantage, of being available in sufficient quantities, and additionally processing the material does not burden the environment. 

To produce a solar cell, the semiconductor is contaminated or "doped". "Doping" is the intentional introduction of chemical elements, with which one can obtain a surplus of either positive charge carriers (p-conducting semiconductor layer) or negative charge carriers (n-conducting semiconductor layer) from the semiconductor material. If two differently contaminated semiconductor layers are combined, then a so-called p-n-junction results on the boundary of the layers

DRAWING ON E-MANUAL

At this junction, an interior electric field is built up which leads to the separation of the charge carriers that are released by light. Through metal contacts, an electric charge can be tapped. 
If the outer circuit is closed, meaning a consumer is connected, then direct current flows. 
Silicon cells are approximately 10 cm by 10 cm large (recently also 15 cm by 15 cm). A transparent anti-reflection film protects the cell and decreases reflective loss on the cell surface



CHARACTERISTICS OF A SOLAR CELL
The usable voltage from solar cells depends on the semiconductor material. In silicon it amounts to approximately 0.5 V. Terminal voltages is only weakly dependent on light radiation, while the current intensity increases with higher luminosity. A 100 cm² silicon cell, for example, reaches a maximum current intensity of approximately 2 A when radiated by 1000 W/m².

 
Current-voltage line of a si-solar cell

The output (product of electricity and voltage) of a solar cell is temperature dependent. Higher cell temperatures lead to lower output, and hence to lower efficiency. The level of efficiency indicates how much of the radiated quantity of light is converted into useable electrical energy.

DIFFERENT CELL TYPESOne can distinguish three cell types according to the type of crystal: 

1.	Monocrystalline
2.	Polycrystalline and 
3.	Amorphous. 

1. To produce a Monocrystalline silicon cell, absolutely pure semi conducting material is necessary. Monocrystalline rods are extracted from melted silicon and then sawed into thin plates. This production process guarantees a relatively high level of efficiency            . 

2. The production of Polycrystalline cells is more cost-efficient. In this process, liquid silicon is poured into blocks that are subsequently sawed into plates. During solidification of the material, crystal structures of varying sizes are formed, at whose borders defects emerge. As a result of this crystal defect, the solar cell is less efficient.   
             . 
3. If a silicon film is deposited on glass or another substrate material, this is a so-called amorphous or thin layer cell. The layer thickness amounts to less than 1µm (thickness of a human hair: 50-100 µm), so the production costs are lower due to the low material costs. 

Note: However, the efficiency of amorphous cells is much lower than that of the other two cell types. Because of this, they are primarily used in low power equipment (watches, pocket calculators) or as facade elements.


Material 	Level of efficiency in % Lab 	Level of efficiency in % Production 
Monocrystalline Silicon 	Approx. 24 	14 to17 
Polycrystalline Silicon 	Approx. 18	13 to15 
Amorphous Silicon 	Approx. 13 	5 to7 

From the Cell to the Module

In order to make the appropriate voltages and outputs available for different applications, single solar cells are interconnected to form larger units. Cells connected in series have a higher voltage, while those connected in parallel produce more electric current. The interconnected solar cells are usually embedded in transparent Ethyl-Vinyl-Acetate, fitted with an aluminum or stainless steel frame and covered with transparent glass on the front side. 
The typical power ratings of such solar modules are between 10 Wpeak and 100 Wpeak. The characteristic data refer to the standard test conditions of 1000 W/m² solar radiation at a cell temperature of 25° Celsius. The manufacturer's standard warranty of ten or more years is quite long and shows the high quality standards and life expectancy of today's products

NATURAL LIMITS OF EFFICIENCY

In addition to optimizing the production processes, work is also being done to increase the level of efficiency, in order to lower the costs of solar cells. However, different loss mechanisms are setting limits on these plans. Basically, the different semiconductor materials or combinations are suited only for specific spectral ranges. Therefore a specific portion of the radiant energy cannot be used, because the light quanta (photons) do not have enough energy to "activate" the charge carriers. On the other hand, a certain amount of surplus photon energy is transformed into heat rather than into electrical energy. In addition to that, there are optical losses, such as the shadowing of the cell surface through contact with the glass surface or reflection of incoming rays on the cell surface. 

Other loss mechanisms are electrical resistance losses in the semiconductor and the connecting cable. The disrupting influence of material contamination, surface effects and crystal defects, however, are also significant. 

Single loss mechanisms (photons with too little energy are not absorbed, surplus photon energy is transformed into heat) cannot be further improved because of inherent physical limits imposed by the materials themselves. This leads to a theoretical maximum level of efficiency, i.e. approximately 28% for crystal silicon.
 
Theoretical maximum levels of efficiency of various solar cells at standard conditions

New Directions

Surface structuring to reduce reflection loss: for example, construction of the cell surface in a pyramid structure, so that incoming light hits the surface several times. New material: for example, gallium arsenide (GaAs), cadmium telluride (CdTe) or copper indium selenide (CuInSe²).

Tandem or stacked cells: in order to be able to use a wide spectrum of radiation, different semiconductor materials, which are suited for different spectral ranges, will be arranged one on top of the other.
Concentrator cells: A higher light intensity will be focussed on the solar cells by the use of mirror and lens systems. This system tracks the sun, always using direct radiation.
MIS Inversion Layer cells: the inner electrical field are not produced by a p-n junction, but by the junction of a thin oxide layer to a semiconductor.
Grätzel cells: Electrochemical liquid cells with titanium dioxide as electrolytes and dye to improve light absorption

Basics of Solar Power

What is a solar cell and how does solar power work? Here you will find a simple introduction to the technology for the uninitiated. 

What is a Solar Cell?

A solar cell or photovoltaic cell is a device which generates electricity directly from visible light by means of the photovoltaic effect. In order to generate useful power, it is necessary to connect a number of cells together to form a solar panel, also known as a photovoltaic module. There is more about the the different types of solar cell here. The nominal output voltage of a solar panel is usually 12 Volts, and they may be used singly or wired together into an array. The number and size required is determined by the available light and the amount of energy required. 
Can the power be stored?

The amount of power generated by solar cells is determined by the amount of light falling on them, which is in turn determined by the weather and time of day. In the majority of cases some form of energy storage will be necessary. 
It is possible to connect an array of solar panels to the mains to assist when the power required is greater than that being generated. The cost of this is offset by selling surplus power back to the electricity company when it is available. 

In this type of system the usual choice for energy storage is the lead-acid battery. The number and type of batteries is dependent on the amount of energy storage needed

. [/b] [/size]

[size=17pt]

[center]

BUY COMPLETE MANUAL ON SOLAR POWER TECHNOLOGY

THIS E-MANUAL IS 750 PAGES

IT CONTAIN ALL YOU NEED TO KNOW ABOUT SOLAR TECHNOLOGY

THIS IS THE E-MANUAL YOU NEED

PAY #1,000:00 FOR COMPLETE 700 PAGES

OF THIS SOLAR TECHNOLOGY E-MANUAL

[/center] [/size]

[center][size=18pt]
DOWNLOAD FREE MANUAL AND ACCOUNT PAYMENT

DETAILS

CALL DANIEL ON: 07027255961, 01-4748802
[/size][/center]