Most wood-based products of whole-wood enterprises are excellent, and most of the complaints that exist are often found in installations, especially door covers. Because the installation is not in place, the joint between the door leaf and the door cover is loose, causing the door leaf to sink, which causes the switch to be unsmooth. The above problems are caused by improper installation and unreasonable.
1. Installation of the door cover (frame)

(1) Combination door frame

The door frame is the basic structure of the wooden door. The parts need to be firmly connected. The installation gap should be tight and flat. The angle between the parts should be 90 degrees to avoid misalignment. This kind of door frame can guarantee the installation quality.
(2) Reserve installation gap

The construction method of the rear plug is adopted, and the installation gap between the hole and the door frame is preferably controlled to be 8 mm to 30 mm. If the gap is too small, the door frame will not be inserted or the fixing material will not be filled. If the gap is too large, the fixing will be weak and the filling material will be wasted.

Solid wood door purchase

(3) Adjusting the verticality

The adjustment of the verticality of the front side is extremely important for the installation of wooden doors, ensuring the appearance and durability, using wooden wedges, rubber hammers, spirit levels and the like.

The installation process and specification requirements of the wooden door, I will collect it after reading it!

(4) hinge installation

Measure the position of each hinge groove on the door frame and the hinge position of the side of the door leaf. If there is any error, it should be trimmed in time. The hinge screws must be screwed in and must be fully loaded.

Wooden door installation

Solid wood door purchase

The installation process and specification requirements of the wooden door, I will collect it after reading it!

(5) Install the door leaf

Use a wooden wedge to raise the door from the bottom and adjust it to the appropriate height to close the hinge and the hinge groove on the door frame, then secure the hinge to the door frame.

Wooden door installation

(6) Door leaf adjustment

After the door leaf is installed, it is necessary to adjust the left and right sides of the door frame gap to be uniform. The specific dimensions are as follows: the door leaf and the upper frame and the side frame gap are controlled at 1.5mm~4.0mm; the door leaf and the ground gap, the inner door should be controlled at 6.0~8.0mm;

Doors and floors, toilets, etc. should be controlled at 8.0~10.0mm.

Solid wood door purchase

(7) styrofoam

Before the styrofoam is applied, it is necessary to clean up the debris left on the wall hole, such as putty, ash, etc., and the amount of glue applied is 70%~90% of the door frame and wall space after expansion and solidification. After the colloidal expansion is performed, the wooden frame is inflated, and if the sewing is less, the bonding strength between the door frame and the wall is lowered.

The foaming agent must be broken into the gap twice. The first time you hit a little bit, you must position it. Be sure to hit the iron piece joint. After the styrofoam is fixed and fixed, try again. The longer the interval between the two glues, the better. .

The installation process and specification requirements of the wooden door, I will collect it after reading it!

( Clean up

After the styrofoam is cured, the exposed gel should be removed by using a wallpaper knife. At the same time, the exposed wooden wedges before the door frame and the wall are removed, and the gap is cut straight to facilitate the installation of the face line.

Wooden door installation

Solid wood door purchase

2. Installation of the door line (door sticker)

Before installing the door cover line, clean the foreign objects inside the escape slot. When cleaning, the corners of the slot can not be damaged. Then install the door sleeve into the slot of the door cover (frame) and fix it with white glue or silicone. Leave a gap of 5mm between the bathroom line and the ground, and then hit the silicone.

The set of wires fixed on the sleeve should be as close as possible to the wall, which is based on its own vertical. It is not based on the flatness of the wall. Sealing is required at the gap.

The installation process and specification requirements of the wooden door, I will collect it after reading it!

Wooden door installation

3. Door fan installation

The gaps at each location after the door leaf is installed should conform to the values ​​specified in the table below. After the door leaf is installed, it needs to be flat and vertical. After the door leaf is closed, it is tightly combined with the sealing strip, does not swing and can switch freely.

Wood door clearance limit and test method

Solid wood door purchase

Wooden door installation requirements and tolerances

The installation process and specification requirements of the wooden door, I will collect it after reading it!

5. Hardware installation

After the hinge and the lock cover are installed, the difference between the height of the door leaf and the door frame is not more than 1 mm, and the tolerance between the notch and the hinge and the lock cover is not more than 1.5 mm.

According to the installation position of the lock, the height of the handle from the horizontal ground is 900mm~1050mm.

Wooden door installation

Generally speaking, the keyholes of the door fans are pre-opened in the factory, and some need to be opened at the site. The flatness and accuracy of the keyhole directly affect the aesthetics and accuracy of the installation of the wooden door, which will be adopted by large enterprises. The method of CNC machining opens the keyhole and keyhole at one time, in order to increase the quality of the product.