Here is a request

Hi Sir, please I have a client who is ready to buy a land rig.

Details as follows:

1.Type of Rig? Land Rig

2. HP 3000HP

3. Psi 15,000PSI

4. Jettison Pressure

5. Drilling depth 35,000ft

6. Drilling pipe 5", 12 stand of 9" drill collars

7. Pulling Capacity 2,100,000lb

8. Mud tank Mud Pumps :
i. Three (3) "New" Gardner Denver PZ-11 Mud Pumps, 1600 HP, Liners 6¼" x 12", 643 gpm
each at 3200 psi driven by 6 each GE-752, 1000 hp
traction motors, furnished with:
1. Unitized on a two-runner oilfield type skid with loading hitches on
both ends for tailboarding.
2. Steel traction motor subbase with two (2) adjustable motor base
plates.
3. Two (2) "New" 752 Series wound DC traction motors. Each motor
to include a 15 HP Blower and junction box with lock out switch.
4. High pressure pulsation dampener, 5000 psi.
5. 3" Relief Valve, manual reset, 1500-5000 PSI with flange
connection.
6. SPM meter (0-200)
7. Pressure gauge, 0-5000 PSI range with flange connection.
8. Pressure and Suction Manifold
9. Discharge strainer block.
10. Suction Strainer.
11. Centrifugal charging pump 5 x 6 with mechanical seal and hard
iron material, all mounted on a mission fabricated steel base with
woods style coupling, OSHA type coupling guard and a 75 HP
1750 RPM, 3 PH, 230/460 Volt, 60 Hz explosion proof electric
motor.

9. Stock

10. Diesel tank

11. How many Generators
C. Engine/Generator Package :
Engine/Generators - Five (5) New Mustang/Caterpillar Model 3512C with Direct
Injection Turbocharged and Separate Circuit After cooled Land Electric Diesel
Engine, Rated 1476 H.P. at 1200 R.P.M. 2007 EPA Non-Road Emission Certified,
with the following standard attachments as listed below :
- Air Inlet System
- Aftercooler core, corrosion resistant
- Air cleaner, regular duty, with soot filter
- Service indicators
- Control System
- ADEM II or US Equivalent Electronic engine control, left hand.
- Requires 24V DC 10 AMP continuous, 20 AMP intermittent, clean
electrical power.
- Radiator Cooled Land Based:
- Outlet controlled thermostat and housing
- Jacket water pump gear driven
- Dual outlet
- Aftercooler fresh water cooling pump (SCAC), gear driven centrifugal.
- SCAC pump circuit contains a thermostat to keep the aftercooler
coolant from falling below 30 deg C (85 F).
- Exhaust System
- Exhaust fittings, flexible, 203 mm (8 in)
- Exhaust flange, weldable, 356 mm (12 in)
- Exhaust manifolds, dry
- Dual turbochargers with w/c bearings
- Flywheels and Flywheel Housings
- Flywheel, SAE No. 00
- Flywheel housing, SAE No. 00
- SAE standard rotation
- Fuel System
- Fuel filter
- Fuel transfer pump
- Flexible fuel lines
- Fuel priming pump, left hand
- Electronically controlled unit injectors
- Instrumentation
- Electronic Instrument Panel, left hand
- Analog gauges with digital display data for:
- Engine oil pressure gauge
- Engine water temperature gauge
- Fuel pressure gauge
- System DC voltage gauge
- Air inlet restriction gauge
- Exhaust temperature (prior to turbochargers) gauge
- Fuel filter differential pressure gauge
- Oil filter differential pressure gauge
- Service meter (digital display only)
- Tachometer (digital display only)
- Instantaneous fuel consumption (digital display only)
- Total fuel consumed (digital display only)
- Engine start-stop (off, auto start, manual start, cooldown timer)
- Lube System
- Crankcase breather, Oil cooler, Oil filter, Shallow oil pan
- Oil pan drain valve, 2' NPT female connection
- Lubricating oil, SAE 10W30, Caterpillar DEO (CG4) 643L or
equivalent.
- Mounting System
- Rails, mounting, floor type, 254 mm (10 in)
- Power Take-Offs
- Accessory Drives
- Upper RH, Lower left-hand Front (available for PTO usage)
- Front Housing, Two-sided
- Protection System
- ADEM II or Equivalent monitoring system provides engine de-ration,
alarm, or shutdown strategies to protect against adverse operating
conditions. Selected parameters are customer programmable.
- Status available on engine-mounted instrument panel and can be
broadcast through the optional customer communications module or
programmable relay control modules(s). Initially set as follows :
- Safety shutoff protection, electrical - oil pressure, water
temperature, overspeed, crankcase pressure, and aftercooler
temperature.
- Air inlet shutoff, activated on overspeed or emergency stop.
- Alarms, electrical - ECM voltage, oil pressure, water
temperature (low and high), overspeed, crankcase pressure,
aftercooler temperature, low water level (sensor is optional
attachment), air inlet restriction, exhaust stack temperature,
filter differential pressure (oil and fuel).
- Derate, electrical:
- High water temperature, Crankcase pressure, Aftercooler
temperature, Air inlet restriction, Altitude, Exhaust
temperature.
- Emergency stop push button, located on instrument panel.
- Alarm switches (oil pressure and water temperature) for
connection to customer supplied alarm panel. Unwired.
- Starting System
- Air starting motor, right hand, 620 to 1034 kPa (90 to 150 psi),
left hand control.
- Air silencer
- General
- Paint, Caterpillar Yellow
- Vibration damper and guard
- Lifting eyes
 
b. Generator - Caterpillar SR4B 1750 KVA or Volvo generator, two bearing,
1225 KW, 867 frame, .7 PF, 600 volt complete with Stator RTD' s, Space
heater, Bus bar and cable access box.
c. Radiators - Conventional style Split Core Radiator (56 sq. ft.) with two
circuits for engine jacket water and after-cooler. Includes: 78" Blower fan, fan
drive, fan pulleys, belt guard, fan guard, fuel cooler and Water connections.
d. Master Skids - Five (5) Two-runner oilfield type skids (40' x 10' -0" x
18" with loading hitches on both ends for tail boarding. Skids to
consist of the following:
- Completely covered with ." check plate
- Drilled and tapped plates for removable arched type roof
connections.
- Drilled and tapped plates for removal of engine pony skid.
e. Roofs - Removable arched type roofs (38' -0" x 10' -0" x 12". Roofs
to consist of the following:
- Six (6) T.S. 4" x 4" x ¼" support legs with bolt hole patterns to
fit tapped holes on skids. Leg supports complete with square
tubing diagonal supports for stabilization.
- Two (2) hinged channel running the length of the roof to
prevent rain run off. Channels cut in 5' -0" sections for easy
handling and located between each engine package.
 

12. Year of Manufacture: 2003 upwards..

13. Manual /Automatic- Automatic

14. Mechanism type, Top Drive, etc SCR System (5 Bay) :
One (1) International Electric Company SCR House. The I- Drive System is
manufactured by IEC Systems LLC and designed and equipped to control and power
the following loads:
- Five (5) A/C Engine/generator sets
- One (1) 3000HP Drawworks, driven by three (3) x 1000 hp (Series) DC Motor
- Three (3) x 1600 hp Mud Pumps, each driven by two (2) x 1000 hp (Series)
DC Motors
- One (1) 1000 HP Independent Rotary Drive
- Top Drive Feeder
15. One (1) 500 bbl Water Tank
Material and labor to fabricate one (1) 500 bbl water tank as per our conversation.
Tanks fabricated on oilfield type skids with loading hitches on both ends for
tailboarding. Skid ends to be covered with ¼" check plate. Tanks complete with the
following :
- Two (2) 3 x 2 x 11 Centrifugal pumps with 25 HP Motors
- Suction and Discharge Piping.
- Two (2) ladder rung to top of tank (In and Out)
- 4" Fill cap
- 2" Outlet
- 1" Drain

16. Drawworks :
- Model - "Rebuilt" National 1625 UE
- Rated Horsepower - 3000
- Drilling Line - 1-5/8"
- Sand Line - Not Required
- Auxiliary Brake - Baylor 7838
- Crown Protection - Crown-0-Matic
- Power - Three (3) DC Motors GE 752 (1000 HP each intermittent, 750 HP
continuous)
- Brake Radiator - Heat Exchangers & Brake
- EZ-Torque Type -1
- Circulation Tank
- Automatic Driller - Martin Decker Satellite.
BruceOnuga

Let's talk on WhatsApp. Kindly check my signature

Mide3367:
Here is a request

Hi Sir, please I have a client who is ready to buy a land rig.

Details as follows:

1.Type of Rig? Land Rig

2. HP 3000HP

3. Psi 15,000PSI

4. Jettison Pressure

5. Drilling depth 35,000ft

6. Drilling pipe 5", 12 stand of 9" drill collars

7. Pulling Capacity 2,100,000lb

8. Mud tank Mud Pumps :
i. Three (3) "New" Gardner Denver PZ-11 Mud Pumps, 1600 HP, Liners 6¼" x 12", 643 gpm
each at 3200 psi driven by 6 each GE-752, 1000 hp
traction motors, furnished with:
1. Unitized on a two-runner oilfield type skid with loading hitches on
both ends for tailboarding.
2. Steel traction motor subbase with two (2) adjustable motor base
plates.
3. Two (2) "New" 752 Series wound DC traction motors. Each motor
to include a 15 HP Blower and junction box with lock out switch.
4. High pressure pulsation dampener, 5000 psi.
5. 3" Relief Valve, manual reset, 1500-5000 PSI with flange
connection.
6. SPM meter (0-200)
7. Pressure gauge, 0-5000 PSI range with flange connection.
8. Pressure and Suction Manifold
9. Discharge strainer block.
10. Suction Strainer.
11. Centrifugal charging pump 5 x 6 with mechanical seal and hard
iron material, all mounted on a mission fabricated steel base with
woods style coupling, OSHA type coupling guard and a 75 HP
1750 RPM, 3 PH, 230/460 Volt, 60 Hz explosion proof electric
motor.

9. Stock

10. Diesel tank

11. How many Generators
C. Engine/Generator Package :
Engine/Generators - Five (5) New Mustang/Caterpillar Model 3512C with Direct
Injection Turbocharged and Separate Circuit After cooled Land Electric Diesel
Engine, Rated 1476 H.P. at 1200 R.P.M. 2007 EPA Non-Road Emission Certified,
with the following standard attachments as listed below :
- Air Inlet System
- Aftercooler core, corrosion resistant
- Air cleaner, regular duty, with soot filter
- Service indicators
- Control System
- ADEM II or US Equivalent Electronic engine control, left hand.
- Requires 24V DC 10 AMP continuous, 20 AMP intermittent, clean
electrical power.
- Radiator Cooled Land Based:
- Outlet controlled thermostat and housing
- Jacket water pump gear driven
- Dual outlet
- Aftercooler fresh water cooling pump (SCAC), gear driven centrifugal.
- SCAC pump circuit contains a thermostat to keep the aftercooler
coolant from falling below 30 deg C (85 F).
- Exhaust System
- Exhaust fittings, flexible, 203 mm (8 in)
- Exhaust flange, weldable, 356 mm (12 in)
- Exhaust manifolds, dry
- Dual turbochargers with w/c bearings
- Flywheels and Flywheel Housings
- Flywheel, SAE No. 00
- Flywheel housing, SAE No. 00
- SAE standard rotation
- Fuel System
- Fuel filter
- Fuel transfer pump
- Flexible fuel lines
- Fuel priming pump, left hand
- Electronically controlled unit injectors
- Instrumentation
- Electronic Instrument Panel, left hand
- Analog gauges with digital display data for:
- Engine oil pressure gauge
- Engine water temperature gauge
- Fuel pressure gauge
- System DC voltage gauge
- Air inlet restriction gauge
- Exhaust temperature (prior to turbochargers) gauge
- Fuel filter differential pressure gauge
- Oil filter differential pressure gauge
- Service meter (digital display only)
- Tachometer (digital display only)
- Instantaneous fuel consumption (digital display only)
- Total fuel consumed (digital display only)
- Engine start-stop (off, auto start, manual start, cooldown timer)
- Lube System
- Crankcase breather, Oil cooler, Oil filter, Shallow oil pan
- Oil pan drain valve, 2' NPT female connection
- Lubricating oil, SAE 10W30, Caterpillar DEO (CG4) 643L or
equivalent.
- Mounting System
- Rails, mounting, floor type, 254 mm (10 in)
- Power Take-Offs
- Accessory Drives
- Upper RH, Lower left-hand Front (available for PTO usage)
- Front Housing, Two-sided
- Protection System
- ADEM II or Equivalent monitoring system provides engine de-ration,
alarm, or shutdown strategies to protect against adverse operating
conditions. Selected parameters are customer programmable.
- Status available on engine-mounted instrument panel and can be
broadcast through the optional customer communications module or
programmable relay control modules(s). Initially set as follows :
- Safety shutoff protection, electrical - oil pressure, water
temperature, overspeed, crankcase pressure, and aftercooler
temperature.
- Air inlet shutoff, activated on overspeed or emergency stop.
- Alarms, electrical - ECM voltage, oil pressure, water
temperature (low and high), overspeed, crankcase pressure,
aftercooler temperature, low water level (sensor is optional
attachment), air inlet restriction, exhaust stack temperature,
filter differential pressure (oil and fuel).
- Derate, electrical:
- High water temperature, Crankcase pressure, Aftercooler
temperature, Air inlet restriction, Altitude, Exhaust
temperature.
- Emergency stop push button, located on instrument panel.
- Alarm switches (oil pressure and water temperature) for
connection to customer supplied alarm panel. Unwired.
- Starting System
- Air starting motor, right hand, 620 to 1034 kPa (90 to 150 psi),
left hand control.
- Air silencer
- General
- Paint, Caterpillar Yellow
- Vibration damper and guard
- Lifting eyes
 
b. Generator - Caterpillar SR4B 1750 KVA or Volvo generator, two bearing,
1225 KW, 867 frame, .7 PF, 600 volt complete with Stator RTD' s, Space
heater, Bus bar and cable access box.
c. Radiators - Conventional style Split Core Radiator (56 sq. ft.) with two
circuits for engine jacket water and after-cooler. Includes: 78" Blower fan, fan
drive, fan pulleys, belt guard, fan guard, fuel cooler and Water connections.
d. Master Skids - Five (5) Two-runner oilfield type skids (40' x 10' -0" x
18" with loading hitches on both ends for tail boarding. Skids to
consist of the following:
- Completely covered with ." check plate
- Drilled and tapped plates for removable arched type roof
connections.
- Drilled and tapped plates for removal of engine pony skid.
e. Roofs - Removable arched type roofs (38' -0" x 10' -0" x 12". Roofs
to consist of the following:
- Six (6) T.S. 4" x 4" x ¼" support legs with bolt hole patterns to
fit tapped holes on skids. Leg supports complete with square
tubing diagonal supports for stabilization.
- Two (2) hinged channel running the length of the roof to
prevent rain run off. Channels cut in 5' -0" sections for easy
handling and located between each engine package.
 

12. Year of Manufacture: 2003 upwards..

13. Manual /Automatic- Automatic

14. Mechanism type, Top Drive, etc SCR System (5 Bay) :
One (1) International Electric Company SCR House. The I- Drive System is
manufactured by IEC Systems LLC and designed and equipped to control and power
the following loads:
- Five (5) A/C Engine/generator sets
- One (1) 3000HP Drawworks, driven by three (3) x 1000 hp (Series) DC Motor
- Three (3) x 1600 hp Mud Pumps, each driven by two (2) x 1000 hp (Series)
DC Motors
- One (1) 1000 HP Independent Rotary Drive
- Top Drive Feeder
15. One (1) 500 bbl Water Tank
Material and labor to fabricate one (1) 500 bbl water tank as per our conversation.
Tanks fabricated on oilfield type skids with loading hitches on both ends for
tailboarding. Skid ends to be covered with ¼" check plate. Tanks complete with the
following :
- Two (2) 3 x 2 x 11 Centrifugal pumps with 25 HP Motors
- Suction and Discharge Piping.
- Two (2) ladder rung to top of tank (In and Out)
- 4" Fill cap
- 2" Outlet
- 1" Drain

16. Drawworks :
- Model - "Rebuilt" National 1625 UE
- Rated Horsepower - 3000
- Drilling Line - 1-5/8"
- Sand Line - Not Required
- Auxiliary Brake - Baylor 7838
- Crown Protection - Crown-0-Matic
- Power - Three (3) DC Motors GE 752 (1000 HP each intermittent, 750 HP
continuous)
- Brake Radiator - Heat Exchangers & Brake
- EZ-Torque Type -1
- Circulation Tank
- Automatic Driller - Martin Decker Satellite.
BruceOnuga

Middleman business no dey get head.

SocialJustice:
Middleman business no dey get head.

na true but who knows? It may work out

Mide3367:
na true but who knows? It may work out

Lol, oya try na. Lol.