₦airaland Forum

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to
empower Nigerians in the management of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train Nigerian graduates and students in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc)
Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)
Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)
CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to empower Nigerians in the management
of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train graduate engineers in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc).
P&ID: (Software that shows detail schematic arrangement of piping, equipment, inline components (Valves, Reducer), control instruments in a process plant), suitable for Process, Mechanical, Instrumentation engineers.

Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)

Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)

CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to
empower Nigerians in the management of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train Nigerian graduates and students in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc)
Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)
Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)
CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to
empower Nigerians in the management of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of paramount interest to train Nigerian graduates and students in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, CEASER II, SOLID WORKS, for engineering designs.
COURSES ON TRAINING
AutoCAD: (A software for all class of engineers, technologists and scientist)

PDMS: (used by mechanical engineers, piping and layout engineers, structural and civil engineers etc)
Aspen-Hysys: (used by process engineers, chemical engineers, petroleum engineers, industrial chemist etc)
Petrel: (used mostly by petroleum and gas engineers ,geologist, geo-physicist etc)
CEASER II: Use for pipe stress analysis

1.AUTOCAD
Introduction to the use of AutoCAD 2D commands
Application in designing of a simple house plan.
Application in electrical surface design and electronic circuit
Simple 2D piping design.
Piping and instrumentation (P&ID) design modeling and piping isometrics
General hatching and gradient modeling.
Introduction to 3D design modeling.
Development of 3D house plan model and roofing.
Introduction to 3D piping modeling
Modeling of mechanical parts and components.
Rendering and material modeling

2. PDMS (Plant Design Management system)
Introduction to different modules of PDMS
Application of design module
Structural design of beams/column ,walls/floor, panels/plates and access, stairs and ladder modeler.
Equipment application is ranging from pumps, distillation columns, storage vessels, exchangers etc
Pipe work routing.
HVAC design modeling, Cable tray, hangers and supports
Converting PDMS Draft and Isodraft to AUTOCAD
Introduction to PDMS project designed to various standards and layout interpretation.

3. OIL AND GAS PROCESSING DESIGN USING ASPEN HYSYS.
Introduction to process engineering and application
Flash calculation and utilities.
Propane Refrigeration loop
Refrigerated Gas Plant
NGL Fractionation Train
Oil Characterization
Gas Gathering
Two-Stage Compression
Acid Gas Sweetening with DEA
Natural Gas Dehydration with TEG
Reporting in Aspen HYSYS
4. Petrel (for sub-surface reservoir modeling and simulation studies).
Introduction and data importation
Seismic interpretation
Fault modeling
Vertical layering
Facies modeling
Petro-physical modeling
Reservoir mapping
Well correlation

Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to
empower Nigerians in the management of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of PARAMOUT INTEREST to train Nigerian graduates and students in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, SOLID WORKS, for engineering designs.
• PLANT DESIGN MANAGEMENT SYSTEM (PDMS) & PIPING AND INSTRUMENTATION DIAGRAM (P&ID).
• PDMS is a customizable, multi-user and multi-discipline, engineer controlled design software package for engineering, design and construction projects in offshore and onshore, oil and gas industry, chemical and process plants, mining, Pharmaceutical and food industry, power generation. Ken Technologies training approach sets to equip trainee industry engineer on how to use PDMS to tackle industry related problems especially in the oil and gas sector.
•
• HYSYS :
• Hysys is widely used software in process, chemical, pharmaceutical, and oil and gas industries.
• Hysys serves as the engineering platform for modeling process and cryogenic facilities, to
• Refining and chemical processes. Ken Technologies carry out professional Hysys training as
• Required by industrial application emphasizing on its unique simulation tools.

AUTOCAD (2D/3D)
AutoCAD is a software application for computer aided design (CAD) and drafting. The software
Supports both 2D and 3D formats. AutoCAD still remains standard software owing to it flexibility in usage. Widely employed in Building, Mechanical, Electrical drawings and design. Ken Technologies provide intensive on 2D and 3D modeling ranging from Building, Mechanical modeling and piping design.
Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE : 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

PROFESSIONAL OIL & GAS AND PIPING DESIGN TRAINING (AUTOCAD, PDMS, HYSYS, P&ID).
Due to the ongoing trend of things in Nigeria industries where almost all aspect of Nigerian industries is been headed and managed by expatriates due to low technical knowhow of Nigerian graduates, a local content policy had been designed by the federal government to
empower Nigerians in the management of their affairs in the absence of expatriates. To achieve this, strategic plans had been mapped out to train and re-train Nigerians to this effect.
On this note, it had been of PARAMOUT INTEREST to train Nigerian graduates and students in the use of sophisticated software like PDMS, P&ID, AUTOCAD, HYSYS, SOLID WORKS, for engineering designs.
• PLANT DESIGN MANAGEMENT SYSTEM (PDMS) & PIPING AND INSTRUMENTATION DIAGRAM (P&ID).
• PDMS is a customizable, multi-user and multi-discipline, engineer controlled design software package for engineering, design and construction projects in offshore and onshore, oil and gas industry, chemical and process plants, mining, Pharmaceutical and food industry, power generation. Ken Technologies training approach sets to equip trainee industry engineer on how to use PDMS to tackle industry related problems especially in the oil and gas sector.
•
• HYSYS :
• Hysys is widely used software in process, chemical, pharmaceutical, and oil and gas industries.
• Hysys serves as the engineering platform for modeling process and cryogenic facilities, to
• Refining and chemical processes. Ken Technologies carry out professional Hysys training as
• Required by industrial application emphasizing on its unique simulation tools.

AUTOCAD (2D/3D)
AutoCAD is a software application for computer aided design (CAD) and drafting. The software
Supports both 2D and 3D formats. AutoCAD still remains standard software owing to it flexibility in usage. Widely employed in Building, Mechanical, Electrical drawings and design. Ken Technologies provide intensive on 2D and 3D modeling ranging from Building, Mechanical modeling and piping design.
Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.
AJAH OFFICE : 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, BY DOREN HOSPITAL
AJAH, LAGOS.

Engineering Design Course on AutoCAD,
PDMS, AutoCAD P&ID, HYSYS
AUTOCAD(2D/3D) ,P & ID, & PIPING DESIGN TRAINING
IN LAGOS



Ken Technologies is an Engineering design company focusing on implementation, Training, consulting and Outsourcing. In the course of our operation we realized that most Engineering firms in and outside the country needs Engineering graduates that are well equipped in the use of the following engineering design Software (AutoCAD/AutoCAD Plant
3D, AutoCAD P & ID, PDMS).





COURSE OUTLINE: PART: A
• AutoCAD( 2D/3D) Drafting/design
• Isometric Drawing
• Isometric Dimensioning
• Converting from 2D To 3 Dimensional Environment
• Modelling of Solid objects( Complex 3 dimensional drawing)
• Application of 3 Dimensional Tools (Slice, Subtract, Extrude, Taper Faces, Union,) Etc.
•
• PART: B ( BASIC PIPING)
• Piping Systems Detail Engineering/Plant & Piping Layout Engineering/ Piping
• Drafting.
• *Basic Principles of Piping and its Components.
• * Piping Fundamentals
• * ASME Codes & Standards
• * Applying AutoCAD 3D Plant Software in Modelling Pipe Fittings(Elbow 90 and
• 45 Degree, Reducer (Concentric and Eccentric), Flanges, Plug, Valves, Tee) etc.
• * Adding Piping Supports(Hanger, Strut) to a Pipe and Piping components using
• AutoCAD 3D Plant.
•
• * Mechanical/Process Equipments
• * Flow Diagram
• Developing Piping and Instrumentation Diagram Layout.
• Adding Flow lines, Instrument lines, Inline Components(Reducer, Valves) to
• P& ID Layout.
• * Interpreting and developing P & ID Diagram and Plant Modelling.
• * Piping Specification, Piping Isometrics
• * Piping & Equipment Layout
•

PDMS COURSE MODULE
• Axis System (Piping Isometric):
• Identification of Equipment and Primitives ( Equipment and Primitives orientation)
• Creating of Equipments (Tanks, Reboiler, Heat exchanger, Column, Pumps)
• Modifying Equipment( Orientate, offset, move)
• Setting Attributes ( Height, Diameter, Position, orientation)
PIPEWORK MODELLING
Piping in PDMS: Basic Concepts
* Piping Specification: Setting the appropriate specification
* Pipe work tool bar
* Pipe creation Form
* Pipe Branch Head and Tail connected
* Creating Branch components (Pipe fittings)
*Pipe Branch Head/Tail position Explicit
* Pipe components creation form
2. Attaching fittings (Elbows, Valves, Flanges, Reducer, Tee, Cap etc) to Equipment
3. STRUCTURAL MODELLING: Designing Beams and Columns:
* Choosing specification for Beams and Columns (British Standard)
* Offsetting Beams and Columns
* Designing Plates and Panel
* Picking Plates and Panels points.





Training Schedule
Morning Session: (10 am- 1pm)
Afternoon Session: (1 am- 4 pm)
Evening Session : (4pm-6pm)
Saturdays 10am-1pm) 7 Saturdays

Fee: AutoCAD (2D/3D) = #30,000.00
P&ID (Piping and Instrumentation Diagram Design and Interpretation) = #10,000.00
Auto Plant (Pipe, Equipment Modelling) = # 20,000.00
PDMS AND P&ID (PIPING MODELING AND INSTRUMENTATION) = #30,000.00
1st Instalment (70 percent of course fee)







WHO SHOULD ATTEND?
Mechanical/Chemical/Petroleum Engineers, Geologist, Electrical/Electronics, Material/Metallurgical, Electrical, Civil/Structural engineering graduate and Undergraduate, Jobseekers, Draftsman.
Training Benefits:
- Excellent Materials Provided (Design Manual/ Chart).
- Industry leading Software used in training (Auto CAD/Auto CAD Plant 3D, PDMS, Pipe fit pro). Full Installation on Student Laptop.
- Certificate in AutoCAD, P&ID, Auto Plant, PDMS.


Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.

PIPING AND INSTRUMENTATON DESIGN (P&ID) DESIGN AND INTERPRETATION
TRAINING

Course Description :
This 3 day course will provide participants with the principles of P&ID drawings which are used in
Process industries. The course is suitable for individuals dealing with P&ID in all process industries
Including chemicals, Oil and Gas, Petrochemical, Water & waste water and Food processing industries.
A road map of P&ID during the lifetime of a design project is studied. Symbols, tagging, and basic explanations of popular items in P&ID drawings are among the topics covered and, for broader understanding, the different arrangements of each item is presented. Additionally given are some rules of thumb.
This course will cover piping, valves and control valves, tank and vessels, pumps, heat exchangers and control systems, including BPSC, SIS, and Alarm.
Each individual concept is reinforced using P&ID schematics specific to the topic.

Course Includes
Real life P&ID’s, Acronym lists, Exercises (for class activity)


Course Description
This 2-day course will provide participants with the principles of P&ID drawings which are used in process industries. This course is suitable for individuals dealing with P&ID’s in all Process industries including Chemical, Oil & Gas, Petrochemical, Water & wastewater, and Food processing industries.

A road map of P&ID during the lifetime of a design project is studied. Symbols, tagging, and basic explanations of popular items in P&ID drawings are among the topics covered and, for broader understanding, the different arrangements of each item is presented. Additionally given are some rules of thumb.

This course will cover piping, valves and control valves, tank and vessels, pumps, heat exchangers and control systems, including BPSC, SIS, and Alarm.
Each individual concept is reinforced using P&ID schematics specific to the topic.

Course Includes
Real life P&ID’s, Acronym lists, Exercises (for class activity)



Who Should Attend
This course is designed for:

• Process Engineers
• Chemical Engineers
• Graduate, Youth coopers, Jobseekers
• Automation Engineers
• Instrumentation Engineers and Technologists
• Mechanical Engineers
• Operation and Maintenance Personnel
• Piping Designers
• CADD Drafters
• HAZOP Facilitators
• Project Engineers.

Course Outline

• P&ID: Its Role, Content, and Milestones
• P&ID Anatomy & General Rules
• Provision for Ease of Maintenance
• Pipes & Fittings: Symbols, Tagging, and Arrangements
• Valves: Symbols, Tagging, and Arrangements
• Control Valves: Symbols, Tagging, and Arrangements
• Containers: Symbols, Tagging, and Arrangements
1. Tanks
2. Vessels
3. Ponds
COURSE FEE: # 15,000.00
DURATION: 3 DAYS
VENUE: 26, IKOTUN ROAD, BY DIAMOND, COLLEGE BSTOP
SUIT15, KAZAM PLAZA, IKOTUN, LAGOS.
Kento2002ng@yahoo.com, Tel: 08060360538, 08028553955.

Engineering Design Course on AutoCAD,
PDMS, AutoCAD P&ID, HYSYS
AUTOCAD(2D/3D) ,P & ID, & PIPING DESIGN TRAINING
IN LAGOS



Ken Technologies is an Engineering design company focusing on implementation, Training, consulting and Outsourcing. In the course of our operation we realized that most Engineering firms in and outside the country needs Engineering graduates that are well equipped in the use of the following engineering design Software (AutoCAD/AutoCAD Plant
3D, AutoCAD P & ID, PDMS).





COURSE OUTLINE: PART: A
• AutoCAD( 2D/3D) Drafting/design
• Isometric Drawing
• Isometric Dimensioning
• Converting from 2D To 3 Dimensional Environment
• Modelling of Solid objects( Complex 3 dimensional drawing)
• Application of 3 Dimensional Tools (Slice, Subtract, Extrude, Taper Faces, Union,) Etc.
•
• PART: B ( BASIC PIPING)
• Piping Systems Detail Engineering/Plant & Piping Layout Engineering/ Piping
• Drafting.
• *Basic Principles of Piping and its Components.
• * Piping Fundamentals
• * ASME Codes & Standards
• * Applying AutoCAD 3D Plant Software in Modelling Pipe Fittings(Elbow 90 and
• 45 Degree, Reducer (Concentric and Eccentric), Flanges, Plug, Valves, Tee) etc.
• * Adding Piping Supports(Hanger, Strut) to a Pipe and Piping components using
• AutoCAD 3D Plant.
•
• * Mechanical/Process Equipments
• * Flow Diagram
• Developing Piping and Instrumentation Diagram Layout.
• Adding Flow lines, Instrument lines, Inline Components(Reducer, Valves) to
• P& ID Layout.
• * Interpreting and developing P & ID Diagram and Plant Modelling.
• * Piping Specification, Piping Isometrics
• * Piping & Equipment Layout
•

PDMS COURSE MODULE
• Axis System (Piping Isometric):
• Identification of Equipment and Primitives ( Equipment and Primitives orientation)
• Creating of Equipments (Tanks, Reboiler, Heat exchanger, Column, Pumps)
• Modifying Equipment( Orientate, offset, move)
• Setting Attributes ( Height, Diameter, Position, orientation)
PIPEWORK MODELLING
Piping in PDMS: Basic Concepts
* Piping Specification: Setting the appropriate specification
* Pipe work tool bar
* Pipe creation Form
* Pipe Branch Head and Tail connected
* Creating Branch components (Pipe fittings)
*Pipe Branch Head/Tail position Explicit
* Pipe components creation form
2. Attaching fittings (Elbows, Valves, Flanges, Reducer, Tee, Cap etc) to Equipment
3. STRUCTURAL MODELLING: Designing Beams and Columns:
* Choosing specification for Beams and Columns (British Standard)
* Offsetting Beams and Columns
* Designing Plates and Panel
* Picking Plates and Panels points.





Training Schedule
Morning Session: (10 am- 1pm)
Afternoon Session: (1 am- 4 pm)
Evening Session : (4pm-6pm)
Saturdays 10am-1pm) 7 Saturdays

Fee: AutoCAD (2D/3D) = #30,000.00
P&ID (Piping and Instrumentation Diagram Design and Interpretation) = #10,000.00
Auto Plant (Pipe, Equipment Modelling) = # 20,000.00
PDMS AND P&ID (PIPING MODELING AND INSTRUMENTATION) = #30,000.00
1st Instalment (70 percent of course fee)







WHO SHOULD ATTEND?
Mechanical/Chemical/Petroleum Engineers, Geologist, Electrical/Electronics, Material/Metallurgical, Electrical, Civil/Structural engineering graduate and Undergraduate, Jobseekers, Draftsman.
Training Benefits:
- Excellent Materials Provided (Design Manual/ Chart).
- Industry leading Software used in training (Auto CAD/Auto CAD Plant 3D, PDMS, Pipe fit pro). Full Installation on Student Laptop.
- Certificate in AutoCAD, P&ID, Auto Plant, PDMS.


Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.

Engineering Design Course on AutoCAD,
PDMS, AutoCAD P&ID, HYSYS
AUTOCAD(2D/3D) ,P & ID, & PIPING DESIGN TRAINING
IN LAGOS



Ken Technologies is an Engineering design company focusing on implementation, Training, consulting and Outsourcing. In the course of our operation we realized that most Engineering firms in and outside the country needs Engineering graduates that are well equipped in the use of the following engineering design Software (AutoCAD/AutoCAD Plant
3D, AutoCAD P & ID, PDMS).





COURSE OUTLINE: PART: A
• AutoCAD( 2D/3D) Drafting/design
• Isometric Drawing
• Isometric Dimensioning
• Converting from 2D To 3 Dimensional Environment
• Modelling of Solid objects( Complex 3 dimensional drawing)
• Application of 3 Dimensional Tools (Slice, Subtract, Extrude, Taper Faces, Union,) Etc.
•
• PART: B ( BASIC PIPING)
• Piping Systems Detail Engineering/Plant & Piping Layout Engineering/ Piping
• Drafting.
• *Basic Principles of Piping and its Components.
• * Piping Fundamentals
• * ASME Codes & Standards
• * Applying AutoCAD 3D Plant Software in Modelling Pipe Fittings(Elbow 90 and
• 45 Degree, Reducer (Concentric and Eccentric), Flanges, Plug, Valves, Tee) etc.
• * Adding Piping Supports(Hanger, Strut) to a Pipe and Piping components using
• AutoCAD 3D Plant.
•
• * Mechanical/Process Equipments
• * Flow Diagram
• Developing Piping and Instrumentation Diagram Layout.
• Adding Flow lines, Instrument lines, Inline Components(Reducer, Valves) to
• P& ID Layout.
• * Interpreting and developing P & ID Diagram and Plant Modelling.
• * Piping Specification, Piping Isometrics
• * Piping & Equipment Layout
•

PDMS COURSE MODULE
• Axis System (Piping Isometric):
• Identification of Equipment and Primitives ( Equipment and Primitives orientation)
• Creating of Equipments (Tanks, Reboiler, Heat exchanger, Column, Pumps)
• Modifying Equipment( Orientate, offset, move)
• Setting Attributes ( Height, Diameter, Position, orientation)
PIPEWORK MODELLING
Piping in PDMS: Basic Concepts
* Piping Specification: Setting the appropriate specification
* Pipe work tool bar
* Pipe creation Form
* Pipe Branch Head and Tail connected
* Creating Branch components (Pipe fittings)
*Pipe Branch Head/Tail position Explicit
* Pipe components creation form
2. Attaching fittings (Elbows, Valves, Flanges, Reducer, Tee, Cap etc) to Equipment
3. STRUCTURAL MODELLING: Designing Beams and Columns:
* Choosing specification for Beams and Columns (British Standard)
* Offsetting Beams and Columns
* Designing Plates and Panel
* Picking Plates and Panels points.





Training Schedule
Morning Session: (10 am- 1pm)
Afternoon Session: (1 am- 4 pm)
Evening Session : (4pm-6pm)
Saturdays 10am-1pm) 7 Saturdays

Fee: AutoCAD (2D/3D) = #30,000.00
P&ID (Piping and Instrumentation Diagram Design and Interpretation) = #10,000.00
Auto Plant (Pipe, Equipment Modelling) = # 20,000.00
PDMS AND P&ID (PIPING MODELING AND INSTRUMENTATION) = #30,000.00
1st Instalment (70 percent of course fee)







WHO SHOULD ATTEND?
Mechanical/Chemical/Petroleum Engineers, Geologist, Electrical/Electronics, Material/Metallurgical, Electrical, Civil/Structural engineering graduate and Undergraduate, Jobseekers, Draftsman.
Training Benefits:
- Excellent Materials Provided (Design Manual/ Chart).
- Industry leading Software used in training (Auto CAD/Auto CAD Plant 3D, PDMS, Pipe fit pro). Full Installation on Student Laptop.
- Certificate in AutoCAD, P&ID, Auto Plant, PDMS.

Engineering Design Course on AutoCAD,
PDMS, AutoCAD P&ID, HYSYS
AUTOCAD(2D/3D) ,P & ID, & PIPING DESIGN TRAINING
IN LAGOS



Ken Technologies is an Engineering design company focusing on implementation, Training, consulting and Outsourcing. In the course of our operation we realized that most Engineering firms in and outside the country needs Engineering graduates that are well equipped in the use of the following engineering design Software (AutoCAD/AutoCAD Plant
3D, AutoCAD P & ID, PDMS).





COURSE OUTLINE: PART: A
• AutoCAD( 2D/3D) Drafting/design
• Isometric Drawing
• Isometric Dimensioning
• Converting from 2D To 3 Dimensional Environment
• Modelling of Solid objects( Complex 3 dimensional drawing)
• Application of 3 Dimensional Tools (Slice, Subtract, Extrude, Taper Faces, Union,) Etc.
•
• PART: B ( BASIC PIPING)
• Piping Systems Detail Engineering/Plant & Piping Layout Engineering/ Piping
• Drafting.
• *Basic Principles of Piping and its Components.
• * Piping Fundamentals
• * ASME Codes & Standards
• * Applying AutoCAD 3D Plant Software in Modelling Pipe Fittings(Elbow 90 and
• 45 Degree, Reducer (Concentric and Eccentric), Flanges, Plug, Valves, Tee) etc.
• * Adding Piping Supports(Hanger, Strut) to a Pipe and Piping components using
• AutoCAD 3D Plant.
•
• * Mechanical/Process Equipments
• * Flow Diagram
• Developing Piping and Instrumentation Diagram Layout.
• Adding Flow lines, Instrument lines, Inline Components(Reducer, Valves) to
• P& ID Layout.
• * Interpreting and developing P & ID Diagram and Plant Modelling.
• * Piping Specification, Piping Isometrics
• * Piping & Equipment Layout
•

PDMS COURSE MODULE
• Axis System (Piping Isometric):
• Identification of Equipment and Primitives ( Equipment and Primitives orientation)
• Creating of Equipments (Tanks, Reboiler, Heat exchanger, Column, Pumps)
• Modifying Equipment( Orientate, offset, move)
• Setting Attributes ( Height, Diameter, Position, orientation)
PIPEWORK MODELLING
Piping in PDMS: Basic Concepts
* Piping Specification: Setting the appropriate specification
* Pipe work tool bar
* Pipe creation Form
* Pipe Branch Head and Tail connected
* Creating Branch components (Pipe fittings)
*Pipe Branch Head/Tail position Explicit
* Pipe components creation form
2. Attaching fittings (Elbows, Valves, Flanges, Reducer, Tee, Cap etc) to Equipment
3. STRUCTURAL MODELLING: Designing Beams and Columns:
* Choosing specification for Beams and Columns (British Standard)
* Offsetting Beams and Columns
* Designing Plates and Panel
* Picking Plates and Panels points.





Training Schedule
Morning Session: (10 am- 1pm)
Afternoon Session: (1 am- 4 pm)
Evening Session : (4pm-6pm)
Saturdays 10am-1pm) 7 Saturdays

Fee: AutoCAD (2D/3D) = #30,000.00
P&ID (Piping and Instrumentation Diagram Design and Interpretation) = #10,000.00
Auto Plant (Pipe, Equipment Modelling) = # 20,000.00
PDMS AND P&ID (PIPING MODELING AND INSTRUMENTATION) = #30,000.00
1st Instalment (70 percent of course fee)







WHO SHOULD ATTEND?
Mechanical/Chemical/Petroleum Engineers, Geologist, Electrical/Electronics, Material/Metallurgical, Electrical, Civil/Structural engineering graduate and Undergraduate, Jobseekers, Draftsman.
Training Benefits:
- Excellent Materials Provided (Design Manual/ Chart).
- Industry leading Software used in training (Auto CAD/Auto CAD Plant 3D, PDMS, Pipe fit pro). Full Installation on Student Laptop.
- Certificate in AutoCAD, P&ID, Auto Plant, PDMS.


Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.

Engineering Design Course on AutoCAD,
PDMS, AutoCAD P&ID, HYSYS
AUTOCAD(2D/3D) ,P & ID, & PIPING DESIGN TRAINING
IN LAGOS



Ken Technologies is an Engineering design company focusing on implementation, Training, consulting and Outsourcing. In the course of our operation we realized that most Engineering firms in and outside the country needs Engineering graduates that are well equipped in the use of the following engineering design Software (AutoCAD/AutoCAD Plant
3D, AutoCAD P & ID, PDMS).





COURSE OUTLINE: PART: A
• AutoCAD( 2D/3D) Drafting/design
• Isometric Drawing
• Isometric Dimensioning
• Converting from 2D To 3 Dimensional Environment
• Modelling of Solid objects( Complex 3 dimensional drawing)
• Application of 3 Dimensional Tools (Slice, Subtract, Extrude, Taper Faces, Union,) Etc.
•
• PART: B ( BASIC PIPING)
• Piping Systems Detail Engineering/Plant & Piping Layout Engineering/ Piping
• Drafting.
• *Basic Principles of Piping and its Components.
• * Piping Fundamentals
• * ASME Codes & Standards
• * Applying AutoCAD 3D Plant Software in Modelling Pipe Fittings(Elbow 90 and
• 45 Degree, Reducer (Concentric and Eccentric), Flanges, Plug, Valves, Tee) etc.
• * Adding Piping Supports(Hanger, Strut) to a Pipe and Piping components using
• AutoCAD 3D Plant.
•
• * Mechanical/Process Equipments
• * Flow Diagram
• Developing Piping and Instrumentation Diagram Layout.
• Adding Flow lines, Instrument lines, Inline Components(Reducer, Valves) to
• P& ID Layout.
• * Interpreting and developing P & ID Diagram and Plant Modelling.
• * Piping Specification, Piping Isometrics
• * Piping & Equipment Layout
•

PDMS COURSE MODULE
• Axis System (Piping Isometric):
• Identification of Equipment and Primitives ( Equipment and Primitives orientation)
• Creating of Equipments (Tanks, Reboiler, Heat exchanger, Column, Pumps)
• Modifying Equipment( Orientate, offset, move)
• Setting Attributes ( Height, Diameter, Position, orientation)
PIPEWORK MODELLING
Piping in PDMS: Basic Concepts
* Piping Specification: Setting the appropriate specification
* Pipe work tool bar
* Pipe creation Form
* Pipe Branch Head and Tail connected
* Creating Branch components (Pipe fittings)
*Pipe Branch Head/Tail position Explicit
* Pipe components creation form
2. Attaching fittings (Elbows, Valves, Flanges, Reducer, Tee, Cap etc) to Equipment
3. STRUCTURAL MODELLING: Designing Beams and Columns:
* Choosing specification for Beams and Columns (British Standard)
* Offsetting Beams and Columns
* Designing Plates and Panel
* Picking Plates and Panels points.





Training Schedule
Morning Session: (10 am- 1pm)
Afternoon Session: (1 am- 4 pm)
Evening Session : (4pm-6pm)
Saturdays 10am-1pm) 7 Saturdays

Fee: AutoCAD (2D/3D) = #30,000.00
P&ID (Piping and Instrumentation Diagram Design and Interpretation) = #10,000.00
Auto Plant (Pipe, Equipment Modelling) = # 20,000.00
PDMS AND P&ID (PIPING MODELING AND INSTRUMENTATION) = #30,000.00
1st Instalment (70 percent of course fee)







WHO SHOULD ATTEND?
Mechanical/Chemical/Petroleum Engineers, Geologist, Electrical/Electronics, Material/Metallurgical, Electrical, Civil/Structural engineering graduate and Undergraduate, Jobseekers, Draftsman.
Training Benefits:
- Excellent Materials Provided (Design Manual/ Chart).
- Industry leading Software used in training (Auto CAD/Auto CAD Plant 3D, PDMS, Pipe fit pro). Full Installation on Student Laptop.
- Certificate in AutoCAD, P&ID, Auto Plant, PDMS.


Management: Ken Technologies
Tel: 08060360538, 08028553955
Email: kento2002ng@yahoo.com
OFFICE: 26, Ikotun Road, College College Bus Stop, By Diamond Bank.
Suite 15, Kazam Plaza.