₦airaland Forum

reajen:
thank @djungle other view of the duplex, call today 08066327787

Nice design.

Still on Crackle Finish...

Continuation of Step 4.
Moisture one sponge and dip it into the polyurethane. Press and lift flattest edge of the loaded sponge against the wall. Don't brush or slide. Don't re-wet an area once you have completed your application because this may pull the existing material off of the surface and reduce the effect.

Some sagging and dripping polyurethane will enhance the appearance of your finish, but heavy, pronounced drips may prove to be too dramatic of an effect once glazed. Allow to dry over night.

Step 5A.
Mix Decorative Glaze: Once the polyurethane is dry, you are ready to mix your decorative glaze. Apply a small amout of the glaze mixture to the moistened sea sponge mitt or a rectangular cellular sponge. Coat the surface evenly using a wooden stir stick or your hand.

Step5
Glaze: Begin in an upper corner and rub the glaze on the wall using a random circular action similar to applying wax to a car. Reload the glazing mitt or sponge often, and blend the area as you move.

Once your finish is dry to touch, gently remove the low-tack tape, reset your room and enjoy your newly personalized space.

Good morning.

Good evening.

Good afternoon.

How to create a Crackle Finish.

Step 1 Apply two Base Coat Color:
Apply two coats of Interior Latex Matte paint as your base coat color, following the label directions for recommended drying and recoat times. Matte finish is required for proper results.

Step2A Caot with Metallic:
After allowing the base colour to dry completely, apply the Faux Impression Metallic. Use a brush to cut into corners and around trim.

Step3 Roll on Crackle:
The following day, roll a thin, even coat of Faux Impressions Crackle over the entire surface using your 6" and 9" premium 3/8 rollers.

Step4 Sponge on Polyurethane:
Between 1 and 4 hours after completing Step3, your walls should be dry, yet slightly tacky to the touch. At this point, you are ready to apply Waterborne Gloss.

Step 4 to 5a and 5b to be continued in our next lesson....

Good afternoon.

Crackle.

Supplies for Artisan Crackle Finish

*Roll low-tack/safe-release tape * Paint tray 9" roller frame *Two 9" Contractor Series® premium roller covers (3/8" nap) *9" Contractor Series® 1/2 nap microfiber roller covers *Nylon/polyester brush *6¼" roller frame *Two 6" Contractor Series® premium roller covers (3/8" nap) *6" Contractor Series® microfiber roller cover (1/2" nap) *Two large sea sponges Symphony by Purdy™ sea sponge glazing mitt *Latex gloves *Gallons of Interior Latex Matte paint (base coat color) *Gallon of Faux Impressions® Metallic *Quarts of Faux Impressions® Crackle *Quarts of Minwax® Polycrylic® Waterborne Polyurethane Gloss *Quart of Faux Impressions® Latex Glaze * Quart of Interior Latex Matte paint (glaze color)

Supplies for Artisan Crackle Finish

*Roll low-tack/safe-release tape * Paint tray 9" roller frame *Two 9" Contractor Series® premium roller covers (3/8" nap) *9" Contractor Series® 1/2 nap microfiber roller covers *Nylon/polyester brush *6¼" roller frame *Two 6" Contractor Series® premium roller covers (3/8" nap) *6" Contractor Series® microfiber roller cover (1/2" nap) *Two large sea sponges Symphony by Purdy™ sea sponge glazing mitt *Latex gloves *Gallons of Interior Latex Matte paint (base coat color) *Gallon of Faux Impressions® Metallic *Quarts of Faux Impressions® Crackle *Quarts of Minwax® Polycrylic® Waterborne Polyurethane Gloss *Quart of Faux Impressions® Latex Glaze * Quart of Interior Latex Matte paint (glaze color)

Artisan Impression.

This includes three application techniques for you to achieve the look and atmosphere you desire:

Crackle
Leaf
Tissue Paper

I will start with Crackle Finish.

.

Supplies available at Abumara GBL 270 Watet Front Plaza, Oniru Bustop, Ozumba, Victoria Island. Call Julia on 07063400771 for more details.

Supplies
* Roll of low-tack/safe-release tape * Paint tray * 9" roller frame * 9" Contractor Series® premium roller cover (3⁄8" nap) * Two 9" Contractor Series® 1/2 nap * microfiber roller cover * Nylon/polyester brush * 6 1/4" roller frame * 6" Contractor Series® premium roller cover (3⁄8" nap) * Latex gloves * Two gallons of Latex Matte paint (base coat color) * A gallon of Faux Impressions® Metallic * A gallon of Faux Impressions® Latex Glaze * A gallon of Interior Latex Matte paint (glaze color) * Mixing container

How to create a Brushed Metallic finish.

Step 1 Apply two Base Coat Color:
Apply two coats of Interior Latex Matte paint as your base coat color, following the label directions for recommended drying and recoat times. Matte finish is required for proper results.

Step2A Caot with Metallic:
After allowing the base colour to dry completely, apply the Faux Impression Metallic. Use a brush to cut into corners and around trim.

Step 2B Back-Brush:
While the area is still wet, hold a dry 9" microfiber 1/2" nap roller cover in your hand and lightly sweep it actossnthe wall in random, overlapping curves. You have approximately 15minutes to back-brush the Metallic before it is dry. Repeat this process across the entire wall, blending edges of each adjacent area as you go.

Once your finish is dry to touch, gently remove the low-tack tape, reset your room and enjoy your newly personalized space.u

Call today for all your painting projects.

Good evening.

A trial will convince you. Call us today, special discount awaits you.

Contact Julia for your Sherwin-Williams paint, wall patching compound, painting supplies, on 07063400771, email:chichijulia@gmail.com
or
visit our office; Abumara GBL Ventures Limited at 270 Water Front Plaza Ozumba, Oniru Bustop, VI. Ask of Julia. We deliver nationwide.

More...

Some Textured Metallic Finish.

Lots of designs available, depending on your Faux impression installer to give you an outstanding designs.

Good morning.

Good afternoon.

How to create Textured Metallic Finish.

Supplies


One roll of 2" low-tack/safe-release tape
Assorted drop cloths and rags
Paint tray
9" roller frame
9" Contractor Series® premium roller cover (3⁄8" nap)
9" Contractor Series® 1/2 nap microfiber roller covers
Nylon/polyester brush
6 1/4" roller frame
6" Contractor Series® premium roller cover (3⁄8" nap)
6" Contractor Series® microfiber roller cover (1/2" nap)
6" Symphony by Purdy™ Sea Sponge mini roller cover
Latex gloves
Two gallons of Interior Latex Matte paint (base coat color)
One gallon of Faux Impressions® Metallic
One gallon of Faux Impressions® Latex Glaze
One gallon of Interior Latex Matte paint (glaze color)
5-quart mixing container


Step 1
Interior Matte Paint - 2 coats which will be your base coat. Matte finish is required for proper results.

Step 2
After allowing the base coat to dry, apply the Faux Impression Metallic. Use brush to cut corners.

Step3. Once the wall is dry and have uniform matte sheen, you are ready to mix your decorative glaze.

Step 3
Moisten a sea sponge roller and roll it into a paint tray filled with the decorative glaze mixture. Start in an upper corner and apply the glaze using a curving motion in an overlapping pattern.

Once your finish is dry to touch, gently remove the low-tack tape, reset your room, and enjoy your newly personalized space.

As the coating industry leader, Sherwin-Williams is committed to offering the most comprehensive selection of paints that deliver maximum performance and reduced environmental impact.

Coming up soon, textured metallic.

Call for more details.

Good evening.

All items available at our store, Abumara GBL ( Source of Sherwin-Williams Paint in Nigeria). Call 07063400771 for more details.