GAZZUZZ:


You would need to visit people who do.

Proper workshop

GAZZUZZ:











Lori iro

Eldersege:
Good morning,

Please I want to buy Nisan Murano 2005. The price is good and the car looks ok but I have never used Nisan especially Murano before. My neighborhood requires raised vehicle due to bad muddy road .

The impression I normally get about Murano is the gear that in normally have gear issued like the 2001/4 model of Honda Odesey and how it is very expensive.

Your advice will be most appreciated.

Thanks..

quam7:
Thanks for the post sir, it was very informative.
I would also like to give my own view on this topic.
Maintaining a car is one of the best way of getting the best out if it, but the reverse is the case here in Nigeria, they always want to spend less maintaining and also get the best out of the car.
One should take his/her car for a preventive or periodic maintainance at least once in a month.
If you want to know more about cars and also want to know how to earn a lot and tons of money from cars.
Hit me up on WhatsApp; 08102802348.
I would be holding an informative class
tonight.

Eldersege:
Good morning,

Please I want to buy Nisan Murano 2005. The price is good and the car looks ok but I have never used Nisan especially Murano before. My neighborhood requires raised vehicle due to bad muddy road .

The impression I normally get about Murano is the gear that in normally have gear issued like the 2001/4 model of Honda Odesey and how it is very expensive.

Your advice will be most appreciated.

Thanks..

obidevine:
Gazzuzz . I've been doing some research on ducraft brakes

What do you think about ducraft brakes?

henryutd:
My toyota corolla 2010 automatic started popping out of transmission during motion. Work was done on it before and it stopped but it has started again. The technicians refused to tell me exactly what he did.

But I noticed the acceleration was not smooth like before after it changes from gear 1 to 2. The gear 2 viberates during motion as if you are using a lower gear.

Presently I can only use it when driving slowly on the street but can't speed up with it.
Any attempt to speed up will disengage the gear though it is on Drive. It will be firing without moving.
Good for street but bad for expressway.

What could be the problem?

DdenslordD:

If you want to use ducraft brakes make sure you buy ducraft discs also both are compactible if you buy only the pads it will damage any other disc you are using even if it is a new disc because ducraft is pure ceramic cannot go on steel discs

Okoyedavid3:
Hi Gazuuz. Nice job you are doing, having read through this trend and it's the most trend were one can find solution to persistent car issues. Thanks once again.

I use a carmy 04 model v6, 1mzfe.

Pls of recent I got my CEL on, scanned it the codes are
P0300
P0301
P0303
P0305
P0420
P0430

Have changed spark plugs, checked coils (with a multimeter they are okay, even swapped coils, since it's a V6 but I still get misfire codes in the banks 1) changed fuel filter, gotten new air filter, serviced fuel injector, at a time I swapped the fuel injector bank 1 to bank 2 and vice versa.

Still get these codes come up after covering 75Miles.

My kazeem says the car compression is okay,


I don't feel any drivability issues. It's revs well and fires well on the road. My mech even took it for s spin drive and said that the car picks very quickly and well unlike other cars he has driven.

Pls Gazuuz and other car gurus, Autologic and all
I need your help in resolving this issue as am not comfortable with these CEL codes being on.

Thanks

Attached is a pics of the CEL codes.

Codedboy95:
Hello guys, I got a Lexus gs300 last decemeber, I didn't know the car will be that low, the road that leads to my house was very bad and the car has been constantly hitting the floor. So i want to ask, can this damage anything in one month? The road has been repaired now but my car now makes a rattle sound anytime i start it, it is worse if it's the first start of the day.

Second question, the two back tyre rims have black residue on them, it even leaves the black dust on the ground, someone suggests i need to change the brake pad? Is that the case?

Third Question, I want to service my car, previous seller was using Toyota SL SAE 20w/50 ( black keg) but i can't find that same exact one here in ibadan, the closest i found is Toyota SJ SAE 20w/50 ( red keg) can i use that instead? Or can i use another oil ( your recommendation?)

Fourth Question, I did wheel alignment a month ago and since then my afs light has been on, it seems i have to make adjustments to the afs sensor? But most mech here don't really know what that is, what do i tell them to check and where? Or can someone recommend to me a good mechanic in ibadan? Thank you

P.s scanner only shows catalyst converter error code

hammedah001:
My car (Rx 350 2011) gear is not working properly so I decided to change it but my mechanic suggest I change it from 22pin to 10pin please is it advisable to change it to 10pin

GAZZUZZ:


What material is Duracraft brake disk made off?

DdenslordD:


Nissan murabo 01-05 were a mistske and were recalled by nissan in 06 so please just go for a more recent year or better still go for toyota or lex

Peppermintflav:

If I'm not wrong the car uses CVT gearbox. I'll suggest you do your research well be buying. CVT na wahala oo!

Peppermintflav:

If I'm not wrong the car uses CVT gearbox. I'll suggest you do your research well be buying. CVT na wahala oo!

DdenslordD:

[color=#770077][/color]
The catalyst on the bank 1 is eaten oit because it is behind the engine and is always heayed up so the oxygen sensor is readig eratically caisijg misfires. Your problem is your catalysts majorly the bank 1

DdenslordD:

If you want to use ducraft brakes make sure you buy ducraft discs also both are compactible if you buy only the pads it will damage any other disc you are using even if it is a new disc because ducraft is pure ceramic cannot go on steel discs

iamezekwesiri:
@Gazzuzz pls help... my 09 camry is showing P00016 upon scan. Crankshaft positioning, Correlation Bank 1 sensor...

What does this mean?
I changed the shaft for the right leg on saturday.

The only thing i notice about my car is that d movement isn't sharp, a bit lagging before picking up.

obidevine:


This is the fallacy of the year. Ducraft only manufacturers brake pads.

. As long as your disc rotors do not have scars and grooves and it’s not rusty you can use your rotors on your new ducraft ceramic brake pads. If his rotors are grooved it will eat up your ceramic brake pads

Okoyedavid3:



The DTC matter taya me. Thanks. Am planning to take it to a tech guy to resolve. Once again thank as I appreciate. Though am not ready to replace the CAT What can I do..

iamezekwesiri:
@Gazzuzz pls help... my 09 camry is showing P00016 upon scan. Crankshaft positioning, Correlation Bank 1 sensor...

What does this mean?
I changed the shaft for the right leg on saturday.

The only thing i notice about my car is that d movement isn't sharp, a bit lagging before picking up.

DdenslordD:
I
If the code came up jist after you changed the shaft my next question is what side of the shaft ? If it is the passengers side the mechanics must have hit the crankshaft sensor while fixing it please go under the car on thay side and check on the crankshaft sensor. Another common cause is a bad OCV 0016 should be on the exhaust side which is back of the engine please remove ans test with a battery if it is working then it means your engine oil is too heavy for the car change it to a synthetic 5W-20 oil.tnks

Grupo:
Car is 2007 Toyota Corolla.

Here is the issue.

If I start in the morning, it starts well immediately. No issues. Then I allow it to idle for like 30 seconds before I drive off.

It would drive well and all.

Then after driving for like 2 minutes, engine would start jerking and making some pulsing sound. If I open the bonnet, I will see the engine jerking seriously.

If I park and disengage the gear, the jerking will continue and RPM will hover slightly above 1. The car’s normal idle RPM is usually around 0.8 (or 800). If I reengage the gear while this is ongoing, the engine would go off.

If I restart it, it will start and the issues will continue. And if I match the gas, it would respond accordingly. But once I remove my leg from the gas pedal, RPM will rest above 1 and the jerking will continue until everything normalizes

This whole episode will last for a minute.

And after that, everything will return to normal again and car will drive well, with no issues again.

I have changed the spark plugs, and cleaned injectors. But this problem persists.

Please, what could be the issue?

P.S. I live in the East. The mechanics here don’t use scanner. So, I cannot run a scan for now. I have ordered a scanner from Lagos which should arrive soon. But before then, I just need to know what I can do to stop this issue.



CC. Gazzuzz
And other experts in the house.