₦airaland Forum

My elevator and rudde built, elevator here produce our pitch and the rudder here produce our yaw by the help of dihedral effect or dihedral force.

thank u.

here is some tip of vedio, soon i shall send the flight vedio..

pleace do waitch the vedio, Run is the name, cause it is dangerous lol, they dont fly they are just crazy, that's why i need ur help @kinzzzzzzzz

Here!?

so here is how i made the rc heli.
Step1: the body is circuit board, drill a hole.
Step2: get a tube add ur bearings.
Step3: add ur brush motor and the tube.
Step4: add ur gears and shaft:
Step5: add landing gears and tail .
Step6: add ur tail motor,
Step7; i use circuit board for the rotor head.
Step8: i made my blade with aluminum and wood,
Step9: i balance the blade both tail and main blade.
Step10: power it with 24v two lead acid battery.
Thank u for helping.

so here is how i made the rc heli.
Step1: the body is circuit board, drill a hole.
Step2: get a tube add ur bearings.
Step3: add ur brush motor and the tube.
Step4: add ur gears and shaft:
Step5: add landing gears and tail .
Step6: add ur tail motor,
Step7; i use circuit board for the rotor head.
Step8: i made my blade with aluminum and wood,
Step9: i balance the blade both tail and main blade.
Step10: power it with 24v two lead acid battery.
Thank u for helping.

am from anambra state onitsha.

Vedio.


whatapp me, 09032292949

how my mini homamade heli crash when i power it using 18v.

hi my name is igwevictor, i made this heli , and power it with 24v lead acid battery, need ur help to make it fly @ kingzzz, they always crash and crash.

kings i di too much, i love ur work

were did u both ur parts?? I love ur work..

waw that a nice work, brother were did u both ur parts??

waw thats a nice work, Brother were did u both ur parts, were do u risite?

step 10: finish
H a v e a s a v e f l i g h t , h o p e u u n d e r s t a n d s o m e t h i n g , i w i l l b e w a i t i n g f o r y o u r q u e s t i o n , h a v e a n i c e b u i l t , t h a n k y o u f o r r e a d i n g a n d t h a n k m e f o r p o s t i n g , t h a n k G o d f or w is d o m .

step9: balancing
After intalling every thing, is now balancing it, why balancing make sure that the nose is more heaver than the tail as the picture show, if tail is heavey add weight on the front, any thing can serve just use ur brain, the nose should not be tomuch haever, look at the hand that's the cg...

step 8: electronics
Now we install,, i use 1000kv brushless motor and 30a esc, i use lithium ion battery, for long flight interval, 11.1v 5000mah 3p3s if you can understand, i pack it my self and make the charger, but lithium polyma is more powerfull than lithium ion, but the time is shot, add you battery at ur cg, motor to esc, esc to battery, esc long wire to receiver (throttle), i use four servo, two servo for ailerons using servo Y cable, gose to ail in your rx(receiver), one servo to rudder, gose to rudd in ur rx, and elevator to elev, and you are done, add ur prop as well.

step7: high wing traner
Now that you plane has stand, it is ready for installation, note: there will be two tiny long iron's that u will add it help to hold ur wing by robber band, so that u can change your battery etc, next is that you will map out ur centre gravity (cg), and point of lift, balance your plane from there.

step6: kite
Kite is a bird, a kite has no airfoil, but it stay's in the air because the wing deflects off of the kite's body, the kite strings keep the kite angled into the wind so that the deflected wing will hold it up, and kite fly with the angle of attack.

step5: lern airfoil wing's
There are many airfoild shap, flat bottom the one am using, symmetrical, semi-symmetrical etc, In rc plane it isn't absolutely necessay for the wing to have airfoil shape to fly, the flat wing can generate lift if it is in clined, upward into the air, Some lift will be generated by air going over the top of the wing, while a lot of lift will come from air being deflected off the bottom of the wing.

step4:wheel's
This one will be funny, i use my mum's travelling bag whel's, two is ok, get wheel holder e.g shaft and hold the wheel to the body, from ground to the motor point is 4inch, i for get were you motor should be add a wood there in a quear shape and a desipline wood to hold it, make a pillar's using carton to hold the bodie's together.

step3: wing
I made my plane wing in a flat airfoild shap, install the shap in an open carborad of 30cm long and 14 cm wide, add the airfoild shap(using tarod wood or join carton by 3) in the open carton and fold it with a eposy gum, add you aileron's (flaparon's), they are 12 cm each, they help ur plane to roll.

step 2: installing ur rudder and elevetor.
ur elevetor should be 12cm * 4.5 +4.5 and wite is 3.5cm, note in a triangle form, your rudder should be 10cm +2.2 and 11cm at the yaw.

step1: the body
cut out any shape u want to use for ur plane, 40cm or 36cm long and 7cm wide inside, and duplicate with it, to form a room for ur housing parts.

Hello every one, my name is victorigwe, i will be teaching you how to make a carboard airplane from scratch build, at ur home it will not cost you up to $50, is true this is my second plane and it work well, dont mind the design, u can make a better one, if you follow this step,' my first plane that i build, was a balsa wood plane, but i distroy it cause it was heavey, and i can't make an airfoild shap with wood, then i deside to build it with carboard.

StreetTV:
You are right. Government should at least help I'm with more training or get him a job in a car manufacturing company. He has the passion.

i sorpot u

waw

waw that was cool
I made someting like that
Trullly nigeria is now inventors
We need sorport from our government, if they help by next 10 to 15 years we will be more than china.
But i dont think that this can fly, or move in water oo lol.

[quote author=victorigwe post=55378062][/quote]

sweet building, dont forget balanceing ur heli, victorigwe on fb..

pic problem