₦airaland Forum

ishayaauta:
Location is Katsina State

I am in Kaduna. Call/Chat me 08033735359

fuckboys:
ah this is 1150w on microwave

1150 na theory. Practical check the model I send well. Max 1000w. Then you can set it in front from 200 - 1000 to microwave. It is settable. I practically run it and confirm on the inverter. Even on the 1000 set, when the oven hot it reduced to 902w on inverter. The thing make sense.

Brightk - mind sharing the model pls

fuckboys:
do you know the model of this inverter or a picture of it?

LG Microwave model MS2535GIS

fuckboys:
Omo who have recommendations for a low wattage microwave wave Biko. Imagine my microwave stated for 700w pulling over 1kw.

LG microwave, new type that you can set the load from 200w - 1,000w. The system I installed in a restaurant is using this type

opt2:
Good afternoon everyone pls am about buying this solar battery is it good

I have installed Next 12v 3.84kwh lithium batteries and they're performing. I installed one on 2kva hybrid, pump water 0.5hp, run fridge, blender, washing machine alternately day time, run no sweat. The good thing is it can deliver high current on demand and receive high current charge. Small but big engine. Where my Zobo, I de come first😀

Nobody is demarketing Victron. You came, you asked, and you receive genuine answer. If you know you don't ask, if you ask you don't know. This is a classroom, let us, those that know and those that don't know, calm down and learn. Make I go drink my Zobo biko😀

FEGEITOK:
My generator was ok until some stupid repair guy altered some settings and while it can charge my Schneider inverter, the SRNE inverter does not like the frequency.

What is the solution to getting the frequency of the generator back to normal?

Is it to change the AVR or is it to use a screwdriver to reset those altered settings? It is Thermocool generator?

Thanks

Call d gen guy to come and help u reset the voltage and d frequency. But they use to tell person straight to buy AVR

Fremlin:
So I am done putting together my 4.2kwh battery and 3.5kva inverter together, but here's the problem, I have been trying to charge with grid, it just won't charge.

It show that there is voltage, but for whatever reason current remains zero, but only spikes to 0.2 at intervals.


I have tried connecting the inverter directly to the grid without breakers and metres, it's still thesame thing.

Who have experienced this before?

From experience, program ur system from SBU to USB then off solar and NEPA breaker then power first NEPA breaker wait like 1minute, power solar breaker.

Also if on NEPA okay but if na generator pls check d gen frequency o. All d best

kristien4:
i have successfully done 440v on a 450v max voc. It worked. Then i did 468v on 450v, hoping the very long wire will probably sag the voltage to 440v, didn't work. Inverter displayed 448 to 455v. And an awful sound was coming from inside the inverter. I had to remove one panel before it stabilised. Verdict : you can get close to the max voc, but dont cross it.

Thanks for the response. This expected setup will likely hit 490v for the 500v max VOC Welion inverter.

With experience on hybrid inverters with 500v max, has anyone try close to 480v or more VOC panel installation?

Good evening my people. Pls who de sell and price:
1. Qasa standing fan 18" QSF-18R with remote.
2. Qasa dry Iron 300w
Thank you

Bruteality1:
Thanks man. Already Installed this 4.2kva and two 230ah Luminous Tubular Batteries with 550wx4 panels and i must confess the experience is so amazing. It's been less than 48 hours it was installed. Will be looking to upgrade in the future to lithium battery.

Enjoy you money my broda. Receive charge to upgrade soon

Good afternoon. Please how much is:
1. Qasa ac/dc 18" standing fan
2. Qasa inverter dry iron 300w

Thank you

Bruteality1:
Good afternoon Beautiful people. I recently got tired of Nepa ish and decided to get a solar system for my small home. 1 freezer, 1 console, 1 TV, 2 fans. I contacted someone who after talking to him we agreed on 4kva which he said will carry my non inverter 1 hp Hisense AC. We agreed on 1.8 and he'll be using 400w panels x 4. I want to know if it's a good deal on my part or if the panels is not enough for that. He sent me some tubular batteries which I'll post below. I'm just new to this and don't want to get burnt. Country hard

Its good that you are here. You already saw the reactions of my people. See u can get something better with ur N1.8m or with just small addition. Now let's recommend solution:
1. Where is ur location?
2. You could go for 2kw panels, 4.2kw Welion inverter, Valto 3.5kw LFP, protective devices, installation. If na me be u, if I go for this, I will ditch the a/c and go for Qasa 18' standing fan jeje de enjoy my life. Tinubu no send anybody o. All d best

Darey00:
Good morning wonderful people.

I stumbled on this thread and its been educative even though i no understand most of the big terms thrown around lol

So i have a small problem or should I say dilema.

My setup:
⁠Battery: Tubular 200Ah, 12V (new) -- Brand is Kartel
Inverter: 1500W, 12V (Sukam Falcon, Pure sine wave)
Solar Panels: 2 × 300W (600W total).

I dont know much about the charge controller but I will attach a picture to help guide whomever is answering.

Load:
Fan - 125 W
TV - 60 W
Laptop - 39W
5 LED bulb lights


I used the battery from Friday evening to Sunday early morning cos our light wasn't good (low voltage). Throughout Saturday from morning till about 5pm i was using TV and the fan whilst charging via solar. At night i used the fan alone till morning.

The battery was low (11.0v) and started charging again via solar around 8am. I plugged a phone and the fan before unplugging everything around 12pm. By 3.30 pm I plugged the fan and lights before unplugging at 5pm. I powered it on by 7pm and within 15 minutes I got a battery low notification to reduce load at 14%. TV and fan plugged. The voltage had dropped from 11.9 to 11.5v too.

I had to switch off the TV and maintained a 003% load to use 11.3v till the morning. On Monday when I got home around 6.30pm I found that it's just 12v on the controller and sure enough, after plugging the TV, it started screaming after 30 minutes.

Now my question is: is there something wrong with the setup?

I got the setup last December and I'm sure of the battery's performance with PHCN for at least 16 hours with average load. Also, my compound borders a storey building that casts a shadwo around 3.30pm so I'm sure that also counts.


Someone suggested i got an mppt controller. Help me guys. I'm fine with normal battery charge but i feel I'm not getting the best out of my solar setup.

Attached is the controller

In addition to other advise, I want to ask about that fan taking 125w or so. If it is one single fan, pls change the fan to lower consuming ones like 20 - 60w. Add 2 more panels, change CC to MPPT where you may connect panels all in series or 2S2P depending on CC volt limit and you are good to go.

Good evening. Pls anyone have used, install or have experience on Prag Triac 20kva single phase wall mount stabilizer? Is it a servo? Thank you

Good evening house. Pls anyone have used, install or have experience on Prag Triac 20kva stabilizer? Is it a servo? Thank you

Good morning. Compliment of the season. Pls help with direct link to AEDunamis and phone. Thanks

jidobaba:
Good morning house.
I have jinko 435w(3pcs) and 555w(2pcs)
Plus a 24v 3kw Inverter and 60A mppt cc.

How can I combine the panels to give best results please?

If the CC max limit can accommodate the 5panels then our consideration is d max VOC then:
1. Parallel 2pcs of the 435 then series it with d third 435 and the 2pcs 555.
2. Either sell off d 3pcs 435w and get more of 555 or vices versa.
Make I go drink my kunu

How much be Powmr MPPT CC 60a

Good afternoon. @OdinmbaNnamdi ur wasap line make we talk.

Good afternoon. @OdinmbaNnamdi ur wasap line make we talk

Good afternoon. @OdinmbsNnamdi ur wasap line make we talk

Good morning my people. Pls who get neatly used 5kva 48v inverter for sale? Wasap 08033735359 now

swagifted:
Like MTN,.... Its everywhere you go... Felicity got nigeria on lockhold...in a house i came to install whole house audio.....imagine having this in a street where the voltage from the grid is less than 130v....thats the situation here.

Wow nepa 119v. Like what I got on one site here in KD. Infact I was getting 110, 108v. Site steady on 220v now. Na servo boost am o. Jordy-ele servo, na Zeestone run am

Good afternoon. Pls on Sako hybrid inverter 3.5kw 24v is the battery LVD settable? Thanks

Chaiii see better soup. We no de close, I for run wire tap small. Enjoy

jonescosmos:
How my set up looks now.

Its true. Installed recently about a month plus now. Impressed with d low voltage handling, compactness and quietness.

Xanderone:
Thanks. How long has it been in use by the client?

I need to take my time on this stab issue and critically weigh my choice before taking the plunge. That LG AC mis-purchase is still giving me PTSD.

@Xanderone I have installed Jordy-Ele 15kva wall mount supplied by @Zeestone for a client working okay. Infact, the client NEPA supply na bad one sometimes 90v - 110v but stabilize 220v to inverter without shaking

idsolarpower@gmail.com

@Swagifted. Ur phone or wasap line make we talk iro of green cars - Toyota.

Good morning. Pls who have used or using Jordy-Ele servo stabilizer. Are they good and true to claim? Thanks