Hello! for those of you that builds rc plane at home and you are have difficulties checking your CG on your airplane click on this video --
https://www.youtube.com/watch?v=SMV_HwsKb5s

here are the swashplate components..an aluminium ball, rod end set/plastic tube,upper plate and lower plate.the lower plate is the antirotating part while the upper plate is the rotating part

i can't upload pictures earlier but I think I can now,first i got an aluminium ball

pics

a mini plastic tube attached to the lower plate,the ball will have to sit freely in the tube then the upper plate will sit on the tube

the first i did was to get an aluminium ball

I will be posting a few steps on how to make your own made swashplate but first what's a swashplate and how it works
A swashplate is a device that controls the direction of a helicopter rotor blades,it consists of two parts the rotating part and anti rotating part............there's a linkage. rods attached to the rotor blades from the upper swashplate and the lower plates linkage rods to the servo
Note:the lower plate and upper plate are connected together by a ball...enough of explanation let's start making

my email is holuwatomiwa96@gmail.com and Whatsapp 09030693116

sign up and open a blog

yea am in nigeria

if i were to test the flight am sure that all what i did is acurate the only tin is d tx and rx servo esc

hello,i just built up my helicopter and it is in good condition.All part was fabricated by me including the swashplate,frame,tail system,rotor head,landing gear etc.the part i need now are the electronic parts which are gyro,tx and rx,servos,lipo battery,esc and battery chargers.if you need to know how i make each parts just post the problem you are having with your helicopter.

If you building a cyclic control heli the swashplate must have bearing in the middle so as to control the heli rotor head right,left,forward,backward etc

Here is how i built it.it depend on what you have,i used belt gear drive of two pieces big and small and i insert a plastic straw into the big belt gear,the smaller gear hole has to be bigger than the big gear so as to move freely then i add a some metal rod to it

It's simple if you are planning to build.The swashplate has no bearing

@you who called me
THE SWASHPLATE
The swashplate i made has no bearing in the middle,it can only create up and movement when it recieve command from the servo.
Here is how i make it,in full details-but first this is how it works.it contains to plastic,one can rotate freely while the other one cannot.
I got the two plastic from a dvd and a tape player.if you check your dvd i mean a spoilt one those gear used to control the open and close of the dvd exactly the one that uses belt drive(the motor has a mini belt gear connected to the bigger belt gear with the black belt)the bigger one in the dvd is the i used as the rotating part.
As for the non rotating part,it is similar to the one gotten frm the dvd but a little bit bigger than it.it perform the same function in a dvd but you can hardly find it in a dvd instead you can get it in your tape
Note- once the two belt gears are ready,you have to put them together.i used a viju straw and i cut it then put it inside the hole of the bigger belt gear and glued then i put the smaller belt gear into the straw because it was a little wider than the straw,so the cause the small gear to move freely while the big gear doesnt.The shaft you would be using should be able to enter the straw.
I melt three hole at angle 180 each on the big belt gear with a tiny metal rod and fold it like a pedal,i did the three times at angle 180 of the big gear.I melt two holes on the smaller on with the rod at angle 90 straight but make sure you didnt melt it through the straw.THE pic Should explain better.

The thread@ www.nairaland.com/2971455/homemade-flybarless-rc-helicopter-nigeria#43492888.
A new nigerian boy who actually build a radio controll helicopter on his,there are lot of talented people we have in Nigeria.GOD BLESS NIGERIA

I spin the heli up but it is not stable due to lack of servo

That Navy Must Be Brave.......Well Please Check This Thread Science/technology Homemade Flybarless Rc Helicopter Nigeria And Pleasf Let Me See Ur Reply

check this thread out at homemade flybarless rc helicopter nigeria and please i want to recieve reply

The pics

Light generator while i was surfing through the internet and just decide to search for a light generator without the use of battery.it is simple!
All you have to do is gett a magnetic wire as long as you want the volt to be,then wind it arouna a metal bar closely with each windings and move a strong magnet close to it and start rotating the magnet round it.
It possible to charge your phone with light.
Note:it depend on the woundings of the coil.

Take a look at this pictures

Episode 2
While on their search their father suddenly appeared and help them in hunting demons and vampires.The demon were looking fop was right in their fathers body,so he was screaming that shout me but sam could not do it instead he shot him in the leg and the demon escape his body.While on their way ,driving they were hit by a truck controlled by a demon and they all faint only dean was in coma,now all the winchester had a terrible accidents WHAT NEXT....

Supernatural an ameria movie.it invovle two main characters brothers sam winchester and dean winchester.Dean was 4 years older than sam,when dean was 4 their mother was killed by a demon Azazel,she interrupted when Azayel was trying to feed sam demon blood and was later rescued by the father john winchester.
After 6years their father went missing and they were in search of him and while doing that they were hunting demons,vampire etc and looking for the demon that kill their mother.To be continued in episode 2.............

i knw na 1-1 dey go play

sorry,you be mugu o sorry,you be mugu o

I just built a rc helicopter and i require a blade for it.so i decided to build my mine.To build your own get these materials: pencil,saw,tyrod(a flat one atleast as a normal heli blade),ruler,knife and sand paper.I documented every details on how i build it check@ homemade flybarless rc helicopter nigeria.

HOW I MAKE MY WOODEN BLADE
My blade was gotten from a tyrod that is used for ceiling.Now you are going to get a tiny one atleast i tinyas a normal rc helicopter blade,i was lucky to get one.
Now,you measure your prefered and suitable length my was 20cm long and 0.9inch wide,use a pencil and rulerto rule the line of the length and width then cut with the saw gently to avoid any damage.After you are done doing that cut the ruled line now you will be having two parts which are the 0.9inch and a small piece.cut the 0.9inch of 20cm wood into two now,you will be having two pieces of 10cm.Balance each wood equally on a weighing balance.shave the two pieces of wood into an airfoil shape with your knife and sand paper smoothly.

Main rotor head pictures