What should I pay attention to when using 105*1.2*16 cutting disc?
I have briefly introduced some of the precautions for the use of the 105*1.2*16 cutting disc , but some users will still encounter such problems when they use them. Today, the aurora abrasives will be introduced to you in detail. Here are some questions you should be aware of when using 105*1.2*16 cutting disc.
1. During the process of using the cutting piece, the room temperature should be kept, and the cutting product should not be stained with water to avoid slipping.
2. The cutting piece has certain wear and tear requirements, and the wear must be replaced to a certain extent. It is not possible to use it beyond the wear requirements in order to save material. This is a very unsafe violation.
3. During the grinding process, the cutting product should be kept parallel with the working water level. Secondly, the user should master the strength and should not be neglected.
4. The use of the cutting disk as much as possible to choose an indoor operation, indoor environment without clutter. In use, you should pay attention to your concentration and not be half-hearted to avoid accidents. If you use it in an outdoor environment, try to choose a quiet environment.
The above are some of the problems that should be paid attention to when using the cutting piece. I hope to help you better use the cutting piece equipment.

What types of super thin 115mm cutting disc are commonly used?
Cutting sheets are widely used in industry, especially when processing high-precision or low-roughness parts or particularly hard parts. Cutting sheets are indispensable. In actual production, the types of cutting sheets commonly used are artificial emery, Emery, corundum, diatomaceous earth, quartz sand, and pumice. The following are some common types of super thin 115 cutting disc that is explained by Aurora Abrasives.
The commonly used types of super thin 115mm cutting disc generally have the following three types:
(1) Oxide abrasives, powdered and lumpy, mainly used for grinding carbon tool steel, alloy tool steel, high-speed steel, and cast iron.
(2) Carbide abrasives, which are powdery and have a higher hardness than oxide abrasives. They are often used to grind high hardness materials that cannot be ground by oxide abrasives, such as cemented carbide, ceramics, and hard chrome.
(3) Diamond abrasives, both artificial and natural, have higher cutting ability than oxide carbonate abrasives, and good eye mask quality, but because of the high price, they are usually only used for grinding cemented carbide, synthetic diamond, hard chrome. And a variety of high hardness materials.

What role does the 4 inches China grinding disc factory play?
In the abrasives industry, the 4-inch Chinese grinding disc plays an important role. Now it has become a kind of grinding tool equipment that many users will choose. With the continuous expansion of the market, there are more and more Chinese grinding disc merchants on the market. So what is the role of the[url= https://www.auroraabrasive.com/4-inches-abrasive-grinding-disc-tools/] 4 inches China grinding disc factory [/url]in today's abrasives industry?
Among the many discs, the 4-inch Chinese grinding disc is the rarest equipment and the most popular equipment for users. The mill can process dozens of materials, and the processing skill can be adjusted between 80-325 mesh.
In the course of the 4-inch Chinese grinding disc, the analyzer has an indirect effect on the fineness of the finished product. Outside the analysis electromechanical, there is a high-speed rotating impeller installation, and the fine powder material ground in the grinding chamber will enter the analysis electromechanical under the action of the circulating wind generated by the blower, and the materials required for the fineness will be installed by the impeller rotating at a high speed. Maintaining a reasonably stable rotational speed of the analytical machine is the crux of achieving a high quality finished product.
In order to protect the fineness of the 4-inch Chinese grinding disc, the fineness of the finished product is inspected in time, the speed of the analytical machine is adjusted, and corresponding records are made to prevent the speed of the self-adjusting analyzer from inducing the fineness of the 4-inch Chinese grinding disc equipment. Uneven.

China grinding disc manufacturer are accelerating their pace of independent innovation
The development of grinding discs has made more and more disc manufacturers in the market, and the market competitiveness has gradually increased. In order to occupy a place in the fierce market competition, China grinding disc manufacturer must constantly innovate products to continuously Pre-development.
According to reports, at the press conference on the operation of the grinding disc in the first half of the China Machine Industry Association, it was pointed out that the independent innovation of China's grinding discs is continuously advancing to the depth level. The pace of independent innovation of some key components and special high-quality raw materials that have been subject to import for a long time is constantly increasing. accelerate.
Since the beginning of this year, China's grinding disc independent innovation activities are being pushed from the host level to the key supporting parts. For example, Northern Heavy Industries relied on a self-made 36,000 tons of ferrous metal vertical extruder to successfully develop large-diameter thick-walled seamless steel tubes that are urgently needed for the production of supercritical boilers.
At the same time, the independent innovation of the high-end equipment of the grinding disc has continuously achieved new results, and the self-sufficiency rate of high-end equipment has been continuously improved. Among them, the world's first positive and negative 800 kV Yunguang UHVDC transmission project completed and the first domestic four-axis CNC precision grinding machine, domestic The birth of the first 1100 MW nuclear power half-speed rotor shows the improvement of China's grinding disc independent innovation capability.
Although the current independent innovation of grinding discs has made certain breakthroughs and gratifying progress, compared with the world's advanced level, there is still a big gap in China's grinding discs, which cannot fully meet the needs of national economic development. This requires enterprises to follow the fundamentals of improving efficiency and quality. Request to continue research and development and production.

What causes the unstable quality of the 115*1*22 cutting disc?
115*1*22 cutting disc is convenient and easy to use. It is one of the grinding tools commonly used in the abrasive industry. However, there are many quality problems in the production process of the cutting piece. The material is multidisciplinary, so the reasons are complex and numerous. Below, I will analyze why the quality of the 115*1*22 cutting disc is unstable:
1. Cutting sheet manufacturing process problems
The manufacture of the dicing sheet is a highly technical industrial product. If there is a quality problem, it can be found in the process of compounding, molding, hardening, and processing.
2, raw materials
Abrasive quality is uneven, and the binder particle size is too coarse, which will affect the hardness and strength of the cutting piece.
3. Inspection equipment problems
Raw material inspection, process inspection and factory inspection are important contents for the implementation of effective inspection and control of cutting sheet production enterprises, but there are few production enterprises that truly standardize management and standardization management. The main problems are incomplete systems, unimplemented functions, lax management, short control of inspection equipment, and poor quality of inspection personnel.
4, equipment problems
The equipment of the enterprise is not complete, the lack of good mixing machine, the tonnage specification of the hydraulic press is too small, and the maintenance of the equipment is poor, and the product quality is not easy to guarantee.

China abrasive tools for metal material spill control method?
China abrasive tools for metal are used as grinding equipment commonly used on the market today, using automated control systems. Not only can it optimize operation, avoid misoperation, but also stabilize the height of the layer, reduce vibration and increase production. However, even the best equipment will also have certain mistakes. For example, the equipment will overflow after a period of use. How to solve this problem when faced with this problem? The following Aurora abrasive tools will come to summarize Control the material spillage of China abrasive tools for metal .
1. In order to ensure that the overflow cannot be too large, the following two gaps should be checked and adjusted before grinding:
a. The gap between the grinding disc and the ventilation ring should not exceed 10mm, otherwise, the airflow speed required to pass through the ventilation ring should be greater than 25m/s.
b. The gap between the grinding roller and the grinding disc is kept 5~10mm. The stones and metal larger than this size are dropped from the grinding disc into the forced air system which is forcibly bulged and scraped by the rotating scraper through the slipper that can lock the air leakage. When the overflow amount is more than 2% of the grinding feed amount, it may be because the grinding roll gap has been greater than 15 mm.
2. Correctly control the total exhaust and power of the mill, the pressure of the grinding roller and the ring of the grinding disc to circulate in the mill, and will not become the overflow material, so that the amount of material overflowing becomes smaller. At this time, use the grinding equipment to stop the time to reduce the friction ring, or temporarily reduce the wind, or adjust the pressure of the roller. Conversely, for small exhaust and resisting rings, the circulating load in the grinding tool will be very low. At this time, if the feeding amount is constant, the overflowing material will increase, resulting in a significant reduction in the efficiency of the grinding tool.

China cut off disc
is a kind of electric tool that is commonly used in our daily life. It can cut the metal flat tube and angle iron. Because the grinding wheel of the cutting disc is brittle and the rotation speed is high, there is a certain danger in use. Therefore, it is necessary to master some knowledge of the correct use of cutting discs in order to better serve the cutting discs.
Use of cutting discs:
1. The cutting disc should be placed on stable ground, away from flammable materials, and the power cord should be connected to the leakage protection device.
Second, the cutting disc should be installed as required, and the test start operation should be stable before starting work.
Third, the clamping device should be safe and reliable to prevent accidents caused by loose workpieces.
4. When cutting, the operator should evenly cut and avoid the front side of the cutting piece to prevent accidents caused by improper operation of the cutting piece.
5. After the work is finished, the surface dust of the grinding wheel cutting machine should be wiped and the workplace should be cleaned. The open storage should be protected from rain.
Before using the cutting disc, carefully check whether the power cord, switch, motor, protective cover, clamp, belt, etc. are intact, whether the screws of each part are loose, whether the grinding wheel has cracks, whether the metal casing and the power cord are leaking. If the problem is found to be repaired or replaced in time, it can be used.

China abrasive tools for metal is a cutting tool widely used in stone cutting, concrete cutting, prefabricated board cutting, processing of hard and brittle materials such as new and old road cutting, engraving, slotting, etc. It is now widely used in industrial production.
The grinding tool is mainly composed of two parts; the base body and the cutter head. The base body is the main support part of the bonding cutter head, and the cutter head is the part which is cut during use, and the cutter head is continuously consumed in use. The base body does not. The reason why the cutter head can cut is because it contains diamond. Diamond is the currently hard material. It rubs and cuts the object to be processed in the cutter head. The diamond particles are wrapped in metal by the cutter head. internal. Today, Aurora Abrasives will share with you the specific classification of Chinese metal grinding tools.
1. Continuous edge metal grinding tool: continuous sawtooth road cutting piece, generally made by sintering method. Commonly used bronze bonding agent as the base carcass material, water must be added during cutting to ensure the cutting effect, and the type of slit is cut by the laser.
2. Tool-type metal grinding tool: The saw tooth is broken, the cutting speed is fast, and it is suitable for dry and wet cutting methods.
3. Turbine-type metal grinding tool: Combining the advantages of the first two and the second, the sawtooth continuously presents a turbine-like uniform convex and concave, which improves the cutting speed and increases the service life.

China cut off disc
are widely used in many industries for their unique performances such as efficiency, convenience, and economy. However, many people have neglected to make reasonable choices of Chinese cutting discs according to the occasions they use. Henan Aurora Abrasives is based on the experience of cutting disc production and sales for many years to share with you the correct selection and use of cutting discs.
First, the occasion of the use of China cut off disc
First, choose according to the occasion of the use of the cutting disc. The performance requirements of the cutting piece are different for different occasions, so it is important to choose a cutting disc reasonably. We have to choose the cutting disc according to the occasion we use, which can increase the safety factor, improve work efficiency and reduce our use cost.
Second, the choice of ordinary cutting discs when using
Ordinary cutting discs usually refer to fixed cutting machines, cutting machines with a power of <3 kW and a rotational speed of 2900 rpm. Ordinary cutting discs typically cut workpieces less than 50 mm in diameter. However, since the cutting power is small in order to reduce the radial frictional resistance, we usually choose a cutting disc with a thickness of 3.2 mm. The cutting disc is thinner and has a certain elasticity, and it feels sharper when cutting.

The high-quality cutting disc feed speed is the feed rate of the sawed stone. Its size affects the sawing rate. The force of the saw blade and the heat dissipation of the sawing area. Its value should be based on the nature of the stone being sawed. In general, sawing the softer stone, such as marble, can increase the feed speed appropriately. If the feed speed is too low, it is more conducive to improve the sawing rate. Today's high quality cutting disc for sale by manufacturers Aurora. Abrasives to introduce you to the use of cutting discs.
Sawing fine-grained structure. Comparing homogeneous granite, it can increase the feed speed appropriately. If the feed speed is too low, the diamond blade is easy to be flattened. However, the coarse-grained structure and the hard and uneven granite are sawed. When the stone is used, the cutting speed of the cutting piece should be reduced, otherwise, the vibration of the saw blade will cause the diamond to break and reduce the sawing rate. The cutting speed of the sawing granite is generally selected within the range of 9m~12m/min.
Periodically applying the surface of the grinding wheel with a certain pressure with polyfluoromethane or molybdenum sulfide can form a film with a low coefficient of friction on the contact surface to improve the grinding state. This type of material can be seen as a solid lubricant or as another form of wheel filling.

[url=https://www.auroraabrasive.com/115-mm-golden-star-cutting-disc/]Super thin 115 cutting disc[/ur]is made of resin as a bonding agent, combined with a variety of materials, especially for alloy steel, stainless steel and other difficult to cut materials, cutting performance is particularly significant. The ultra-thin cutting piece of Henan Aurora Abrasives is made of resin as a bonding agent, combined with white corundum, Ming corundum, green silicon carbide, single crystal corundum, and other materials, and uses advanced production technology to produce ultra-thin cutting blades. The degree is several times that of other factories at present. This is a lot of comparison tests, no doubt. At the same time, our ultra-thin cutting piece has high flatness and the cutting error is less than 0.02mm. Now let us introduce this ultra-thin cutting piece.
Super thin 115mm cutting disc product features and advantages:
Super thin 115mm cutting disc is made of resin as a bonding agent, combined with a variety of materials, especially for alloy steel, stainless steel and other difficult to cut materials, cutting performance is particularly significant. Dry and wet cutting methods make the cutting precision more stable. At the same time, the choice of material and hardness of the cutting piece can greatly improve your cutting efficiency and save your production cost. The cutting piece is widely used in developed countries such as Europe, America, and Russia, and is highly praised by customers. Users who need it are welcome to come and buy.

4 1/2 super thin cutting disc selection skills?
Now 4 1/2 super thin cutting disc have become the type of cutting commonly used by users, but for some novice users, the choice of cutting blades is also very important, so what are the skills of 4 1/2 super thin cutting disc when choosing? Come and summarize it for everyone today.
For the selection of the cutting piece on a common machine, the cutting piece on the cutting machine usually refers to a fixed cutting table, a cutting machine with a power of <3 KW and a rotation speed of 2900 rpm. Conventional cutters typically cut workpieces that are less than 50 mm in diameter. However, due to the small cutting power in order to reduce the radial frictional resistance, we usually choose a cutting piece with a thickness of 3.2 mm. The cut piece is thinner and has a certain elasticity, and it feels sharper when cut.
Although it is a small cutting piece, it has a lot of attention. In daily life and work, we must strictly select according to the operating standards, otherwise it may bring serious consequences. Henan Aurora Abrasives Co., Ltd., a major engaged in Zhengzhou cutting film, professional manufacturer of polishing sheet production and sales, we use the most advanced cutting instruments, our products are strictly in accordance with the operating standards, product quality has been recognized by the majority of consumers, is your most intimate partner.

What are the advantages of China grinding disc manufacturer?
For [url= https://www.auroraabrasive.com/4-inches-abrasive-grinding-disc-tools/] China grinding disc manufacturer [/url], energy efficiency and inventory management need to be improved. This section is relatively poor for Chinese companies. Many companies do not think about energy management concepts, including equipment management concepts, from the perspective of energy efficiency. For example, we recently did an energy efficiency improvement project for a central enterprise and found that when maintaining equipment. Their goal is that this equipment can operate normally, without stopping, without failure, without affecting production.
In terms of energy efficiency, many specific parameters do not meet energy efficiency requirements. Some parameters of the grinding disc can be maintained by the equipment, which can make it reach the best operating state, but the actual operating state and the best state are even worse than 20%. In fact, as long as some small changes, it can greatly improve energy efficiency.
As for inventory management, as long as you are determined to control, it is easy to do it through hard work in a relatively short period of time. It is more difficult to change the concept and ability of all front-line employees, including middle-level managers, in real manufacturing. Difficult, it is very important.

How to correctly use 105*1.2*16 cutting disc?
With the development of the cutting blade industry, there are more and more users who use 105*1.2*16 cutting disc , but for some users, when using cutting blades, the cutting blades are always damaged. Why? What happened? How do users use the cutting disc correctly?
1. When the flatness of the cutting piece is poor, the cutting surface is curved. As the cutting depth increases, the cutting piece is subjected to lateral stress increase. When the round trip is repeated, the grinding wheel will be cracked and cause "soft film". rupture.
2. When the cutting piece is unevenly organized, with the torque force, thermal stress, tremor and other factors of the cutting process, the stress will accumulate in the weak tissue, leading to cracking.
3. When the hardness of the cutting piece is high, the radial torque force of the cutting piece will increase. Since the thickness of the cutting piece is usually less than 4mm, the cutting piece will be broken.
4. When the cutting piece resin lacks toughness, since the grinding wheel piece is always in a negative pressure state during the cutting process, lateral stress is inevitably generated, and when the cutting piece cannot resist the lateral force, the grinding wheel piece will be broken.