₦airaland Forum

inze:
Funny enough, but the recipient may not see the sarcasm in your statement and attempt to do as stated.

zeekleo:
Hello please I just got this Honda shuttle I have experienced Honda leg pulling already and someone told me the legs can be changed to Renault and all leg problems will stop how true is this ?

Hotzone:
C as mumuness engrossed ur mentality
Chief Security Officer of the State now become civilian in ur mumu world

diportivo:
throw 'em 4-bangers outta the door bro

let psp truck do the rest

#IStandWithJagermeister

will you swear by 4cyl if I dash you this?

EgunMogaji:
Well, to each his own.

Different vehicle demands different engine.

BMW, an industry leading builder of extreme performance vehicles, have gone back to 4 cylinder engines, mostly.

I've played with a lot of cars. From 35 horsepower Austin Mini to 300 horsepower Mitsubishi Evolution.

My current sled is a MINI Cooper S with turbocharged 4 cylinders, there has never been a day that I've wished for a V6 engine in it.

So, to each his own.

LAUSUG15:
Hello, please i have a nissan altima 2005. I want to use it on uber or taxify platform. How do i go about it? Didnt even jnow how to do vehicle inspection. I need a driver as i dont have a valid driving licence. U can chat me up on 08106900128.

luvinhubby:
As i did not get your call, means those last engines are delivering maximum horse power.

leksonltd:
Good day, pls an intending uber partners/ driver. Want to know if Peugeot 307 2007 model will pass uber test.

it will pass with ease

franklin93:
Hello guys, pls I need help. I want to convert my peugeot 406 v6 phase 2, manual transmission to ew10 and I was told I need to buy a couple of things like new ew10 engine, driving shaft, gearbox, engine wire, dashboard wire, half exhaust and complete brain box. My reason for conversion is because my body is almost new and I don't want to sell it.

On the other hand, I was told that since some people replace their ew12 engine with ew10 on same gearbox that I might not need a new gearbox since v6 & ew12 uses same gearbox. However, I am not sure and I just want to hear from your guys if you know how true it could be so I can save some money. I will appreciate your replies pls.

fidet1:
UPDATE- The car has been found in Kaduna.

kingreign:
King GAZZUZZ spotted

need my limbs intact, I will be cheering you guys from the side lines, while sipping my origin

Denn:
I did not infer installation the other way round.

I said he should take account of the jiggle valve.

You can re-read my earlier post again for clarification.

Cheers

Denn:
Did the issue start after the thermostat installation?

If yes, kindly confirm if thermostat was installed properly taking into consideration the alignment of the jiggle valve.

Secondly, ensure radiator cap still seals properly.

Finally, be on the lookout for head gasket symptoms.

Cheers

princetom1:
I dey fear since GAZZUZZ dey write like a left handy (right to left) bt it's relieving now to see he is back on

thanks for reminding me

Since I start de fry my hair, all my fellow pastors de fry hair, I wan see if dem go follow type like me

connkg:
Night Watch = Watch Night. All join.
Will there be an "Open Day" so guarantors can see what and where the students learn?

_{Guarantors bring your cars...}

that ya engine oil neva due?

Specialist900:
Weld Ball joint? Abeg o

Nah secret no tell any body

realbee:
My Oga I cannot stop o, my fiancee is living there and man has to visit once in a while, except if you have another okpeke you want to dash me .

Thanks for your quick response boss. I'll probably disturb you on phone by Monday.

I hope shes on NL, you will explain ya sef

realbee:
Hi everyone, Please I need urgent advice, I drive a 2006 Honda accord (bought as Nigerian use in April this year). I changed the front left (driver side) shaft in early June and few weeks later, I started hearing some noise from that end while driving on the new Ikorodu road (at speed of around 80km/ph). I took it to my mech immediately I got home and after investigating, we discovered the hub is damaged.
There is nothing wrong with the hub before the shaft change and it was not giving any noticeable sign prior to this. I changed the complete hub on the advice of my mech.

Less than a month later (sometimes in July), I started to notice the driver side tire shakes when I accelerate, took it to mech again, we jacked it up and noticed the tire is shaking, investigated further and the hub is damaged again, I was furious because we bought a tokunbo at 13k on the advice of this guy (I'll like to add here that this is my first car, I have only used it for 5 months and hence, just getting to know and understand things about cars in depth). This time he suggested we install a new hub ring instead of buying the entire hub. We did this at a cost of 8k plus workmanship.

Yesterday I went to pick my fiancee from her Ikorodu home and again, I start to notice the vibrations again when I speed. Went to mech again, alas, the hub ring is damaged, again! after arguing back and forth. My mech just `discovered` the shaft I changed in June has a smaller head (the side that was suppose to fit into the hub ring, the green part in the sample image below) and does not fit perfectly into the hub, causing it to move and vibrate inside the hub ring and hence damaging it.

I'll need the advice of the experts in the house if this is possible as I don't trust the words of my mech again, do Honda accord shaft differ (his excuse is that the one fitted initially might be for a 04/05 accord) and can this really continuously break the hub ring? I am also open to advice and suggestions from the experts and anyone who has experienced something similar. My mech is suggesting we change the shaft as well as reinstall a new hub ring.

The lord is saying, stop goingg to ikorodu





Wrong Cv joint damaging Wheel bearing/Hub.

Replace mechanic.

naijadriva:
Honda cars are good but the major nightmare the owners face is the lower ball joint pulling off, sometimes at odd hours, U-turns, roundabouts, highways and so on. Honda also make luxury Acura versions that some have ball joint problems. Below is a list of, but not all, honda that have this problem:
1. ACCORDS and Acura equivalents.
a. Fourth generation (1990-1993): Honda “hala”
b. Fifth generation (1994-1997) Honda ”bulldog” and the European spec. Honda ”Bullet”
c. Sixth generation (1998-2002) all with N. America spec. Honda ”Baby Boy”
d. Seventh generation (2003-2007) all with N. America spec. Honda ”End of Discussion”
2. CRV’s,etc
Note that not all Hondas (e.g Civic, City etc) have this problem and it has been corrected in latest models (2009 and above).
Honda City does not also have this problem. 95% of mechanics do not have this piece of information I am sharing free of charge.
The steps are:
1. Take your car to a GOOD mechanic in your area or you can do it yourself (Like me)
2. After he loosens the hub from shock, tie rod etc,
3. Fix a new original ball joint (some recommend OEM) but for me, the one you use is ok.
4. IMPORTANT! Wait! Before he fixes the hub to the shock etc, take it to a panel beater (most mechanic workshops have one) and ask him to ‘TACK’ (weld just enough to hold it) the head of the ball joint in three equidistant points, where it attaches to the hub as illustrated in the picture as shown here》》》

https://naijadriva./2015/07/20/lasting-solution-to-honda-ball-joint-problems-2/

Marpol please Ban this kazeem from cartalk forever

gbolly707:
@greenhulk is there any special precaution to bleeding the system. I tot I bled it before I started having this issue