₦airaland Forum

latest fight more are coming on v-man studios. https://youtu.be/JdauB

after soldering u will tape the solder part and cover it, add a little glue to hold the teeth to the body, now you are done, here is the circiut of Y and D hope this little tutorial work for you? Stay toon for the next see you.

Now use select your copper and start winding.

Okaakoko:
Following. What about standing fan coil rewinding?

standing fan are in runner, and 220v compatible, i don't wind that,
u can follow the brushless for, but u will have an out put of 4 after winding, the winding teeth is at the position of magnate and the shaft is at inside, having a two ball bearing, it can only work with a capacitor.

Step3 Copper size

In this project i use the same size of copper used in real brushless motor for rc, you can use 34 , 36 , 39 size. So i bring out 2 yard times 3 and join them in one before winding, see the diagram on how to wind.

Step2 Re-winding Base

the process is simple, you will have to turn cw and ccw, the photo will explain it better.

step1: Get the motor
The hard part is removing the coppers, what i use is supper glue remove, after romving the copper you may end up wounding the teeth insulator, use a paper tap to round the teeths.

Hello every one, i am your host igwe victor, today i will be teaching on how to rewind a brushless motor, rc or any brushless, here i will be teaching on D soldering wich is for thrust, but i will show u and analytic image of a Y soldering wich is for speed, with this steps you have no need of buying another expensive motor.
Lets say, i both a new motor and i have not use it for long, and it got burnt, don't throw it away u can make it better as new.

wow what software are u using? let me guess this is blender, or toonboon let me say it is swish mix, nice work, i love animation use it for presonal vfx and i green screen with them...

hi guys you cant control an experiment gliding plane, i dont build that type again i have new once check my fb page v-man innovation, i Have new for the world soon i will start posting here again...

RCDIY:
If this is a brushless motor (I can only see two wires as opposed to three for normal brushless motors), where is the speed controller?!
How do you control throttle?

Quite a confusing design

this is not a motor that is normally use for rc, this motor have an inbuild esc, and it use sensor in it, the capacity is 12v 2.50a, you can find it in electronic shops, the motor increase speed when power is in. And more over you can't control it, throw it from a cliff or mountain or hill to glide, it will glide till it power is draw, add up the elevator and glue it, so that it will be gliding facing up, and when it land it will be save, and some V dihedral on the wing, one you balance the cg very well and Vertical stabilize will do the trick and it will fly.

to buy rc tx rx click . www.aliexpress.com

uwadia79:
hi bro I know how to program pic,but I still need to know how to program Arduino.

how ps tell me

calculate

work done

going

please! understand the picture image, and what i right on it, u can use hobby motor, but i use diy motor to start this.

going

change

step 3 renovated, things has change, if u dont wana use the first step, use this.

Make sure you are straight in mersurment.

If you cant make a diy brushless motor, you can use a real 1000kv from www.aliexpress to do this project. And 30a esc

this is how to make manual rc heli fly without radio and receiver, only esc and servo test can do the job. Step 1 gose on.

matrixme:
I see you're a very creative young man. Rather than make toy helicopters, can you make these projects? I will personally help you commercialize it. Do get across. Best regards.

https://www.youtube.com/watch?v=7sLr2SY7CfQ

https://www.youtube.com/watch?v=arojsvK1xS4

yes i can make air pump is just a simple project, if the material is there.

this step will help you make your own heli fly.

this step will help you make your own heli fly.

that why i make the net 5 duble and not only dust even solid sand or object

uwadia79:
hi bro I know how to program pic,but I still need to know how to program Arduino.

tell me please

y u dy lie for africa, u will also say vigor will pass throw Jupiter, also say 12 revelation 1, 2 end virgin will bear a son on 23
these are lie no x planet, let 23 reach, stop spreding forc news to fretting pple, it has happ before in 2000 lol fear cut all mens and wombmens,

cool