EcoSelect (Interior Semi-Gloss)

EcoSelect is an affordable option when budgets are tight and a zero VOC coating is preferred or required.

Ecoselect has good spatter resistance and is great for use on walls and ceilings of wallboard, primed plaster, wood, and masonry.

Semi-gloss also available in SUPER PAINT & EMERALD.

Visit our office at 270 Water Front Plaza, Oniru Bustop, Ozumba, Victoria Island, lagos. Or call 07063400771 for more details.

Next on product selection. ...(Faux Impression)

Halleluia, The Lord is risen......
May every part of our lives that needs divine touch, receive the resurrection power of the most high God.
HAPPY EASTER

Faux Impressions® Latex Glaze

The various effects available from Faux Impressions®
Latex Glaze are accomplished by applying 1 or more layers of colored glaze over a base coat.
Since the Latex Glaze is translucent (tinting creates a transparent glaze and mixing with paint creates a semi-opaque glaze), the basecoat color influences the finished appearance.
It is a recommended practice to preview color choices on a 2 ft by 2 ft practice board prior to painting your project area.


Why You'll Love It

Allows the creation of a variety of finishes on interior walls, doors, trim, and furniture.

The special effects are developed by sponging on or off, ragging on or off, and combing.

Depending on the tools used, many other imaginative effects can be made, such as faux marble and leather.

Techniques

Smooth Fresco , 
Textured Metallic , 
Crackle , 
Leaf Impressions , 
Rag Rolling, 
Sponging , 
Textured Fresco ,
Tissue Paper Impressions.

latex glaze

I will post pictures of glaze designs.

Latex glaze designs. More designs available.

Question:
Are there any issues associated with painting over a textured surface?

Answer:
A common problem with existing textured paint is that it can be water-soluble. If you use a waterborne product directly over such a surface, it may cause the existing texture to begin to soften and fall off of the surface. Test a fast-drying alkyd primer on the surface. Alkyds have the best chance of not wetting the texture paint. If the alkyd primer does not prevent the softening of the texture, then you may have to consider complete removal of the existing texture and reapplication of a new coat.Application of a fresh coat by roller may be easiest for most; however, in some cases it may not be possible to roll over texture paint as this, too, could cause it to come off. In such cases, application via airless spray may need to be considered. Test the application method over a small area prior to painting the entire surface.

For more details about the recommended alkyd primer for your texture surface, please call 07063400771 or visit our office at 270 waterFront Plaza, Oniru Bus Stop, Ozumba, Victoria Island.

Note; Special discount await any nairalander that visit our office. Simply ask of Julia for your discount.

Contact Abumara GBL for your Sherwin-Williams Products, ranging from wall paint, stucco, faux impression, industrial and commercial flooring, Marine Coating, steel paint, wood paint, patching compound, painting supplies etc.

Good morning.

Sherwin-Williams coatings enhance curb appeal with beauty and durability.
We have 15years, 25years and life time warranty paint interior and exterior.
Call for more details. 07063400771, 08098389501.

Faux Impressions® Metallic Base

Metallics are innovative, roller applied glazes with a high metallic shimmer.

Why You'll Love It

Provides several unique finish effects including Smooth Metallic, Brushed Metallic and Textured Metallic

Techniques

Smooth Metallic ,Brushed Metallic ,Textured Metallic ,Crackle , and Tissue Paper Impressions

Good morning.

Good afternoon.

A trial will convince you.

LECTURE TIME.

How to Create a Smooth Metallic Finish.

Items needed:

* Low-tack/safe-release tape
* Paint tray
* 9" roller frame
* 9" Contractor Series premium roller cover (3/8" nap)
* 9" Contractor Series microfiber roller cover (1/2" nap)
* Nylon/polyester brush
* 6 1/2" roller frame
* 6" Contractor Series premium roller cover (3/8" nap)
* 6" Contractor Series microfiber roller cover (3/8" nap)
* 1 or 2 gallons of Interior Latex Matte paint ( base coat color) depending on your wall surface to be covered.

General Preparation:
Clear the area of all decorative items and move furniture to the center of your room. Protect any adjacent surfaces such as ceilings, wood trim and baseboards by masking them with low tack tape. Properly clean and prepare all surfaces prior to applying any products.

Step1. Apply Base Coat Color:

Apply two coats of Interior Latex Matte paint in your base coat color, following the label directions for recommended drying and recoat times. Matte finish is required for proper results.

Step 2. Coat with Metallic:

After allowing the base coat to dry completely, apply the Faux Impression Metallic. Use a brush to cut into corners and around trim, but immediately blend it into the body of the wall using a 6" microfiber 1/2" nap roller. Cover the remainder of the walls using a 9" microfiber roller.

Once your finish is dry to touch, gently remove the low-tack tape, reset your room, and enjoy your newly personalized space.

Will upload pictures soon...

All items available at our store, Abumara GBL ( Source of Sherwin-Williams Paint in Nigeria). Call 07063400771 for more details.

Good evening.

Call for more details.

As the coating industry leader, Sherwin-Williams is committed to offering the most comprehensive selection of paints that deliver maximum performance and reduced environmental impact.

Coming up soon, textured metallic.

How to create Textured Metallic Finish.

Supplies


One roll of 2" low-tack/safe-release tape
Assorted drop cloths and rags
Paint tray
9" roller frame
9" Contractor Series® premium roller cover (3⁄8" nap)
9" Contractor Series® 1/2 nap microfiber roller covers
Nylon/polyester brush
6 1/4" roller frame
6" Contractor Series® premium roller cover (3⁄8" nap)
6" Contractor Series® microfiber roller cover (1/2" nap)
6" Symphony by Purdy™ Sea Sponge mini roller cover
Latex gloves
Two gallons of Interior Latex Matte paint (base coat color)
One gallon of Faux Impressions® Metallic
One gallon of Faux Impressions® Latex Glaze
One gallon of Interior Latex Matte paint (glaze color)
5-quart mixing container


Step 1
Interior Matte Paint - 2 coats which will be your base coat. Matte finish is required for proper results.

Step 2
After allowing the base coat to dry, apply the Faux Impression Metallic. Use brush to cut corners.

Step3. Once the wall is dry and have uniform matte sheen, you are ready to mix your decorative glaze.

Step 3
Moisten a sea sponge roller and roll it into a paint tray filled with the decorative glaze mixture. Start in an upper corner and apply the glaze using a curving motion in an overlapping pattern.

Once your finish is dry to touch, gently remove the low-tack tape, reset your room, and enjoy your newly personalized space.

Good afternoon.

Good morning.

Some Textured Metallic Finish.

Lots of designs available, depending on your Faux impression installer to give you an outstanding designs.

More...

Contact Julia for your Sherwin-Williams paint, wall patching compound, painting supplies, on 07063400771, email:chichijulia@gmail.com
or
visit our office; Abumara GBL Ventures Limited at 270 Water Front Plaza Ozumba, Oniru Bustop, VI. Ask of Julia. We deliver nationwide.