Speed bumps are raised devices, parabolic in shape, placed across the road to slow traffic.. The sloped design over a 7 or 14 foot length of space encourages cars to slow down without coming to a halt. Often considered the most traditional physical traffic calming solutions, speed humps calm traffic more gradually then speed bumps, although less so than speed tables. They are ideal for residential roads and are generally used to bring speeds to between 10-20 mph.

Speed bumps should ideally be installed in a series to create ongoing traffic calming. They are best placed mid-intersection on roads with low speed limits. Hiphen Solutions speed bumps are available in heights of 3 or 4 inches. Often used in lengths of 7 and 14 feet, the humps can be customized to any length and to the width of your roads in increments of 18.

bump3

Installation Tools

Chalk
Measuring tape
Impact or hammer drills. We recommend that you have two heavy duty hammer drills (Preferrably spline drills).
High speed drills. We recommend that you have two electric drills.
Drill bits carbide tip, at least two 9/16″ dia. , 10-12″ long
3lb Hammer
10lb Sledge hammer (for final adjustment)
11/16″ drive socket with a 12″ extension
Street broom
Utility knife or a hack saw (used for trimming the rubber as needed)
Crow bars, gooseneck wrecking bars
Portable air compressor able to maintain 120psi (used to blow out the debris after the holes are drilled)
Generator and extension cords to run all four drills
One 24″ 2″X4″ piece of wood (used to know the panels in place)
Appropriate signage in accordance to ITE’s State of the Practice on Traffic Calming, as well as ITE’s Manual on Uniformed Traffic Control Devices (MUTCD)

Installation Process

Step 1. Clean the surrounding installation area by using the street broom.

Step 2. Using the Chalk, mark a line parallel to the curb and one that is perpendicular to the road. Use these lines to square up your Traffic Calming Product.
Specifications
Dimensions of the modules:

Width:18” (+/- 1/16”)
Length: 42” (+/- 1/8”)
Thickness: 3” (+/- 1/8”)
Dimensions of the Speed Humps/Tables: (width and length of speed hump are adjustable)

Width: from 7’ up, by 3.5’ increments
Length: according to a street width, from 6’ by 1.5’ increments
Height: 3” or 4”
Standard dimensions of the Speed Humps/Tables:

Width: 7’, 14’, 21’
Length: according to a street width
Height: 3” or 4”
Entrance and exit gradient: 1:15
Side gradient: 1:3
Material: Compression molded 100% recycled synthetic and natural rubber composite
Physical properties:

Tensile strength: minimum 500 psi
Shore hardness: minimum 70A
Specific gravity: 1.1

Marking: rubber modules are available in black or black with yellow or white reflective tape

Material: 100% recycled synthetic and natural rubber composite

WE CAN INSTALL IN ANYWHERE IN NIGERIA

Speed bumps are raised devices, parabolic in shape, placed across the road to slow traffic.. The sloped design over a 7 or 14 foot length of space encourages cars to slow down without coming to a halt. Often considered the most traditional physical traffic calming solutions, speed humps calm traffic more gradually then speed bumps, although less so than speed tables. They are ideal for residential roads and are generally used to bring speeds to between 10-20 mph.

Speed bumps should ideally be installed in a series to create ongoing traffic calming. They are best placed mid-intersection on roads with low speed limits. Hiphen Solutions speed bumps are available in heights of 3 or 4 inches. Often used in lengths of 7 and 14 feet, the humps can be customized to any length and to the width of your roads in increments of 18.

bump3

Installation Tools

Chalk
Measuring tape
Impact or hammer drills. We recommend that you have two heavy duty hammer drills (Preferrably spline drills).
High speed drills. We recommend that you have two electric drills.
Drill bits carbide tip, at least two 9/16″ dia. , 10-12″ long
3lb Hammer
10lb Sledge hammer (for final adjustment)
11/16″ drive socket with a 12″ extension
Street broom
Utility knife or a hack saw (used for trimming the rubber as needed)
Crow bars, gooseneck wrecking bars
Portable air compressor able to maintain 120psi (used to blow out the debris after the holes are drilled)
Generator and extension cords to run all four drills
One 24″ 2″X4″ piece of wood (used to know the panels in place)
Appropriate signage in accordance to ITE’s State of the Practice on Traffic Calming, as well as ITE’s Manual on Uniformed Traffic Control Devices (MUTCD)

Installation Process

Step 1. Clean the surrounding installation area by using the street broom.

Step 2. Using the Chalk, mark a line parallel to the curb and one that is perpendicular to the road. Use these lines to square up your Traffic Calming Product.
Specifications
Dimensions of the modules:

Width:18” (+/- 1/16”)
Length: 42” (+/- 1/8”)
Thickness: 3” (+/- 1/8”)
Dimensions of the Speed Humps/Tables: (width and length of speed hump are adjustable)

Width: from 7’ up, by 3.5’ increments
Length: according to a street width, from 6’ by 1.5’ increments
Height: 3” or 4”
Standard dimensions of the Speed Humps/Tables:

Width: 7’, 14’, 21’
Length: according to a street width
Height: 3” or 4”
Entrance and exit gradient: 1:15
Side gradient: 1:3
Material: Compression molded 100% recycled synthetic and natural rubber composite
Physical properties:

Tensile strength: minimum 500 psi
Shore hardness: minimum 70A
Specific gravity: 1.1

Marking: rubber modules are available in black or black with yellow or white reflective tape

Material: 100% recycled synthetic and natural rubber composite

WE CAN INSTALL IN ANYWHERE IN NIGERIA

HIPHEN SOLUTIONS SERVICES LIMITED

Please CALL: 0703-514-6988, 0807-779-7562, 0802-589-7223, 0818-116-0990
Email: info@hiphensolutions.com
Web: www.hiphensolutions.com/products