harshimyomesk:

Thanks for your input, to answer your questions.
1. No change of any of those parts.
2.no work done on the shaft either.
3. The seal is intact, the leakages stop once the inner cv-axle is Puch back in the gearbox. And this stay ok for awhile

GAZZUZZ:


If the pic below does not solve the problem, then check next post.

GAZZUZZ:
[/color]

[color=#990000]

In 2022, I installed a very expensive transmission (over 4m) and it was having a similar issue. Everything was working well but the shaft kept shifting back and caused a leak which would eventually destroy the transmission if not sorted. Most transmissions arrive the market after very serious accidents and sometimes they display varying degrees of failure.

I remembered the Peugeot 407 axle designs, they were never fitted with retaining pins at the axle head to keep them affixed to the transmission, rather they had a coil spring inside the inner side cv axle. The coil spring created pressure and kept the axle locked to the transmission.

PS I used a valve spring as the coil spring.

Warning only message me if it works fine. Any other message you are on ya own

jceesquare:

You'll need a mechanic to physically inspect your CV axle assembly (rod, cup, head, and the likes), hub, and drive axle.

harshimyomesk:

Thanks my oga, we adjusted(alittle expansion) the retainer spring, still same thing.

Louisking:
Good morning Mr Gazzuzz.
For sometime now I notice when I rev or accelerate my kia rio 2007 model it emits blue smoke. But when on idle it doesn't smoke only when I rev it or on speed, let's say 2.5rpm above. My mechanic said I will need to ring the engine, but am suspecting my valve seal, I change my oil every 2months so am kind of doubting the rings. And I was also told by a colleague not to ring the engine, that most kia don't come out good after ringing. Plss ur opinion will be much appreciated. Thanks

jceesquare:

If you've done that and it still pops out, then I'm afraid you have a bad differential.
You might need to change the differential (good luck sourcing for one and fixing), or change the transmission as a whole.
Or do it the African way. Cut a large chunk of rubber slippers (mechanic should use his discretion) and add inside the cup, fill the cup with generous amount of grease and slap the shaft inside then you'll be good to go.

t2sco:
Good morning Mr Gazzuz. Pls my 010 Corolla did overheating, after changing the gasket, the car work is high, the rpm goes up intermittently and consume fuel badly. Kazeem claim is rewire work, rewire did his best and refer me back to mechanic.. please how do I retify it

mojounited:
Hello Gazzuzz, My 2007/2008 Lexus GS350 AWD has vibration issue when car accelerates upon switching from gear 1 to gear 2.

Also, there is check engine lights and noisy legs issues to sort.

Kindly assist. I wouldn't mind coming to you.

Many thanks

GAZZUZZ:


Unsupported vehicle

Kenosky1:
Hello Gazzuz,
My 2009 Camry vibrates when accelerating and behaves as if the tyres are wobbling. I have 4 brand new tyres and have done alignment and wheel balancing on the car yet the problem persists. Please can someone advise on how to solve this problem.

solutionboy:
Senior man.

Can you please help me interpret these codes for Toyota Corolla 2007. Recently have been having too many problems arising from this car and its quite frustrating. Ran a scan and the undermentioned popped up

P0171 System too lean
P0012 Camshaft timing over retarded
P2195 02 Sensor signal stuck lean bank1sensor1
P0138 02 Sensor sensor circuit high voltage

Atimes in traffic or at stoplights, engine will vibrate and off

Hostermipo:
Good evening Oga GAZZUZZ,

Please my steering is always very hard to turn when I am stationary while pressing break, until I lift my foot from the break or throttle a little before if functions normally again. It makes it really difficult to come turn or come out of very small space.

Please advise

GAZZUZZ:


Replace power steering pump.

solutionboy:
Good day sir. I drive a Toyota corolla 2006 and for sometime now my engine has been running rough with occasional fluctuation in rpm. It only stops when I turn on the AC but continues when its off or thermostat cuts.

I recently ran a diagnosis on it and the error codes are P0012 and P0016. I consequently ran a search on the aforementioned codes but still don't understand. Could you please point out the issue(s) to me.

Thanks a whole lot sir.

mattbass:
Good works my elders.
Please my Honda civic 2010 model keeps blinking the drive light when engaged. It doesn't stay permanent when on drive mode but other options like park when engaged doesn't blink.
My mechanic says is the gearbox and he checked but still remain and everything regarding the gear box was serviced but still no solution.
What could be the possible cause

jceesquare:

Scan the transmission with a good scanner

Freethought:
Good morning Mr gazzuz, i recently bought a naija used Hyundai Sonata 2010, the car stops while on motion after driving a few distance, brings out smoke from the oil tank in the bonnet.. When the bonnets opened, a mixture of water and oil is also noticed on the bonnet body.

My engineer is saying he needs to ring the engine.

Kindly advice

remi4ever:
Hello my honda accord doesn't brake like other cars. I have to depress it harder.

I have changed my master cylinder. I suspect the servo is bad.

jceesquare:

How do you know it's the servo and not the master cylinder?