₦airaland Forum

I wouldn't rely completely on that scan code.

But it's possible the engine Ecu is bad.

An engine requires compression, spark and fuel in the right sequence.

When the car shuts off find out what is lacking. Also clear that error and see if it comes up again.

Corrola 05, paintwork started.

Pics later.

Accord 07, kpom sounds on the front right wheel were caused by 2 things.

1. Bad lower ball joint.

2. No anti squeal in brake pads.

Ball joint replaced.

Peugeot 406

Oil seals leaking.

Crankshaft oil seal(both)

Timing belt will be replaced

Clutchplate and disk will also be replaced.



www.nairaland.com/attachments/2966378_img20151014163629_jpeg1954795fce3e06e0442f2058f58dbb47 www.nairaland.com/attachments/2966377_img20151014163624_jpeg1a2d5de9d7c6dcf1befa8b0895155f82 [img][/img]

Pilot 2012

Paint work complete.

www.nairaland.com/attachments/2974409_img20151019081810_jpegba760392f43814b444c8a3ad2efa1fec www.nairaland.com/attachments/2974410_img20151019081826_jpeg5f18422ba0afdf7a4a71a647c904d695 www.nairaland.com/attachments/2974411_img20151019081854_jpeg52c5619ef4818feac2ab90dce18c77b8 www.nairaland.com/attachments/2974412_img20151018110951_jpeg2a30299d459d31d479bf685eac907d5e

Upholstery work complete.

Corrola 07 engine is mounted, starter mortor, clutch plate, CV joints in terrible condition.
Gear oil also has some liquid in it(milky colour)

Waiting for customer to approve supplementary budget

www.nairaland.com/attachments/2966370_img20151016152429_jpeg643d7c7c3c53f9d3f2a91947758dad20


www.nairaland.com/attachments/2966371_img20151016152440_jpeg53a29256ae072b6108e00aeda746ecdb

ukata16:
@Gazzuzz good afternoon.
I noticed that my honda accord 98 is a rust bucket cos the doors have noticable rusts, the back tire area has opened into the trunk area.
A panel beater has said the fuel tank will be removed for a thorough job to be one.
My question is this- do you also do such works? Cos I will prefer a lasting solution to this embarrassing issue.
Thanks

Rust rust rust.........

I flee from rust.

It is fixable but I avoid such jobs.

ifeanyi83:
Your mastery of automobiles is really amazing. You appear to have answers to every question. I use a Honda civic 2008 model and recently I realised that each time I put the car in drive especially early in the mornings, I hear this funny squeaky noise which stops after a short while. Kindly help with this issue. Regards.

Squeeky sounds

A lot could cause the squeekies, but my guess, based on the age of your car is, worn out brake pads or substandard brake pads.

The brake pad wear indicators could have kicked in and currently doing their job.

[img]http://t0.gstatic.com/images?q=tbn:ANd9GcQatIua0tmtn3j8qSkfQmYE_DBA2F0EqfF61Ak4prtai8NDixn_[/img]

nickxtra:
Please, my car makes one kpro kro sound when I apply breaks on start up. But in motion, it does not make the sounds. A mechanic examined it nd told me it is the break pad, which he advised me to get Yamashida break pad to change the current break pad. But I have been unable to get the Yamashida break pad type for the car(1998/1999 Nissan Primera 2.0i salon car). Also the front inner upper arms of the car makes kiti kiti sounds on motion when driving in bad or uneven roads(usually slowly), but former mechanic said it is stabiliser bushes, but I have to change the entire stabilisers, yet the sounds persist. It was later discovered by my new mechanic that it is not stabiliser problem but the two upper arms need changed completely. Please I need the guru in the house to help me confirmed the problems , the solution and cost of the upper arms nd the yamashida break pad. I have searched around Zuba spare parts market for the yamashida break pad, but did get the type for the car.

I hear a kitity kro kro sound, Ifa what can it be?
[img]http://t3.gstatic.com/images?q=tbn:ANd9GcRZOLAuLlpW29GoyV3rmZQc02IB76-8B7Y9G7orgM7Y5pKBE9kC6Q[/img]

Impressive!























Till the parts full market I no de buy am.

chukel:
I don't care how u want to do it. Just post those pics here. I'm very impatient o I believe mechanics work on Saturdays too. So we want to see appreciable work done today via pics. If e hard u, go gazzuz thread (pic dump) and dump ur pics there. We will gladly look up the pics there.

@ bolded

[img]http://t3.gstatic.com/images?q=tbn:ANd9GcS72xxSCckVoApbVAENTnDNptW5GyFzbiGsvPGXC4roufwkETa4PQ[/img]

amakasparks:
my mechanic can't actually find the leakage he said it maybe from around the shaft area, please what can be done. the gear changes fine but when the oil is down it misbehaves.

The yellow kekenappep?

It's your CV joint (shaft) seal. Remove the CV joints from the transmission and change the seals.


[img]http://t0.gstatic.com/images?q=tbn:ANd9GcQOuPR0Hu2YU9aQSggj7EMkEgkW04UHv3J2yL0buDKiQsZPMgVu[/img]

Toh you parked like and idiot.

I need more of that sticker sef to share.

marshall4:
I drive an Accord 2007 V6. When I push the brakes hard, I could feel some grinding vibration on my foot which gives a poor braking distance. The brake disc and pad have been changed. What is the cause and solution pls? Also, I haven't changed the Transmission oil yet at 71k miles..Do I need to change it? I have the ATF-Z1 at the finger tips.

Thanks

Replace/resurface brake rotors.

The bolded is palm oyel. Please use DW1

Marpol they are above 2 of them.

[img]http://t0.gstatic.com/images?q=tbn:ANd9GcQaU8BY8-FXtianjdWjzjlEgiklO0HhWP5LNpnlXK7ujYGrWJteSw[/img]

Abeg 25year ban go de ok

casid:
Hello House,

I am on the verge of buying another gear for a Honda Accord 1999( baby boy 4 cylinder). The D4 sometimes do not drive unless I put it in other gears(D3 to 2 to 1) till it picks; however, this is done randomly. This only happens whenever I have a stop but moves perfectly on the move. Someone advised that its a gear selector issue to be changed and others say I have to buy another one..

Though, its relatively cheap but mehn that money plenty on the other hand.

Please I need your view on this; if truly is to buy another gear or to fix the gear selector.

Thanks.

Gazzuz, lomomike, cardoctor, luvinhubby, et al, pls assist

Have the vehicle scanned. If there are no codes, replace the transmission.

Pilot 2012 is cooking in the spray booth, pics very soon.

Peugeot 607 engine down. (will be doing an autopsy later tonight)www.nairaland.com/attachments/2966343_img20151016123756_jpeg9ff1da2f8e0a00cec36cd22f86e3f25e www.nairaland.com/attachments/2966344_img20151016142820_jpeg7eba2b0efc30c8559e29208cf004aa21. www.nairaland.com/attachments/2966350_img20151016142802_jpegb17ba7496fccdfce5c12cda6aebf2b52

Corrola 2007 engine down.
www.nairaland.com/attachments/2966351_img20151016144133_jpega4799aeb3e7d76d9063a0a2b6fd9de20 www.nairaland.com/attachments/2966352_img20151016145053_jpegc7c8ef493a4e1bf903fe362dcf6fc3c6

www.nairaland.com/attachments/2966353_img20151016145522_jpeg355efde5f2d98d84f961e9189dbf1ed0

Corrola 2005

New A.C condenser installed, new radiator installed.

Paint works starts tomorrow.

www.nairaland.com/attachments/2966979_img20151016182950_jpeg420d5448ab7a306472b54e4dc104acf1

www.nairaland.com/attachments/2966980_img20151016182235_jpeg6bbcda8e8656d8198ce8b87b8d7f92e1

www.nairaland.com/attachments/2966978_img20151016182741_jpeg6835cc636471b6af22c86c2a91e47ee1


A.c is back to factory specs.

andresia:
I recently had a crash with my car (a baby boy 98 4plug) and one of the switch on the gearbox got broken.

Pls how can it be replaced as the switch seems to be glued together with the gearbox

Gazzuz, lomomike, cardoctor, luvinhubby, et al, pls assist

I uploaded a video for you to see how it's done on whatsapp.

If it's not clear, let me know I'll upload another in my FREE time.

Accord 2002

Gear box supplied ready for installation.

www.nairaland.com/attachments/2963654_img20151015191216_jpegd5496a33f7e6731f6a385c7b2ecdc48d

Honda accord 2002

Transmission slip. (no transmission codes)
A.c work
Noisy rear.
O2 sensor codes
Random multiple misfire
Vtec sensor not working.

Iv got 3 clients following their repairs from asia, europe and somewhere in westafrica.

Thank you for the trust and patronage.

GAZZUZZ.

08023251039

amkob:
Again, to demonstrate that I do NOT want to deliberately blackmail, de-market, dis-credit, insult or offend you...I have intentionally posted my reply on this thread instead of your repairs thread. In addition, I do not see the benefit to me, you or the client of opening another thread of issue(s).

My brother, GAZZUZZ...

Looking at your last reply, there are alot words/commentary I would have used to reply them but whats the use?
Will the words fix the issue(s) NO
Will the words make you pleased? NO

I could have told you details of how I offered and initiated a partial refund of N2,000,000 i.e. two million naira (bank receipt still exists till date) to customer after I had bought, shipped and delivered his SUV complete with original clean title documents, shipping receipts+Bill of Lading and Customs papers, just for peace and to save my name. But why bore ourselves with history?

Thus, I will try not to use too many more words.
You may not agree with my statements (and that is normal) but I believe they are clear enough.
If you had OR have any complaints with customer's conduct at any point during the work, kindly address the client directly and promptly.
No one is perfect, including me.

Right now, I will try to invest my resources in fixing my strained relationship with "your client?" arising from this work. It a relationship that has existed for years and I do not think engine, money or spare-parts can buy it...

You so called friend/client (if it's not you) is not a straight forward person.

* He has no trust
* Does not live up to agreements made on.
paper.

Please go through the paper work in his possession. It is stated clearly what he paid for, and what he didn't.

He has a scanner he scanned his vehicle he has a lean mixture code on bank 1. Pic above is that of his scanner.

A lean mix is not life threatening but unfortunately he did not pay me any diagnostic or scanning work.

He complained about a tapping noise, the noise is from the valves and they require adjustment (every 15,000miles) I did not raise the issue of the tapping because

It would require opening a tokumbor engine and after wards installing new rocke arm seals. The way (you)/your client was complain about money I didn't want to bring up more parts to the situation. As I said, before the job was completed he had already come to the workshop with a taxi to collect and sell his old engine and compressor as scrap in ladipo. I had to fore warn him to remove and keep his (throttle body, coils, injectors, coolant sensors, crank sensors cam sensors, e.t.c) as they might be useful in future.

I rent a very expensive workshop, I don't work under a tree and running round in circles for a customer that DEFRAUDS you does not make it any better.

Your friend(you) is not a good person and I am not ready to work for him any more.

I have blocked him on whatsapp and I do not pick his calls. Please since you are (him) his friend ask him if he still wants the a.c compressor?

My offer on the engine has left the building.