₦airaland Forum

olenyi: If this doesn't work.

Then check ur connection with another mpeg 4 rx.




Regards.

blexxonmak: Try 12428H 11200-3/4 (DVB-S2 QPSK).And as you can see from the parameters you can only access the channels using an MPEG4-compliant decoder.Cheers.

olenyi: Just had a brainwave.

Are ur sure u are at Dstv position? Kindly scan that green freq on ur pix above and post the channels for us to see.

Regards.

olenyi: Now this is something. If u have access to another decoder, try connecting that one lets see what happens.


Regards.

Jackobite: is it on 12245h27500 or 12275h11200 check this frq if it pop out?then try 2 increase by tweak ur lnbf! And feedback d house

olenyi: What's ur signal level on the Dstv channels and is ur rx MPEG4 complaint?


Regards.

olenyi: Have u considered that the C-Band lnb could have gone bad? That a major possibility. If possible for u, try changing the lnb. (hope the dielectric is still intact).

Also ur dish, do u get ku stations in the west like nss7? What ur percentage? And also on intelsat 20ku (68'e) what's ur percentage?

Kindly answer all the above questions pls. This is to enable me diagnose what exactly could be the problem.

Lets get ur C-Band working once more.


Regards.

agitator: no cable connecting ur cband lnb to the receiver

agitator: your C-band is not connected from the pix its standalone no cables connected to the lnb

Bowofola213: Plz hw much is d jack use in rotating d big dish

olenyi:
Dats the good thing with ''experience''. U would have come across a whole lot of different scenario's which gives one an edge.

Will attend to your C band query later.

Regards.

olenyi: So good to hear this. Was it the west maneuver that u used. Was fulfilling being of help.

Regards.

obnelly: Is there any big deal on that sat?Idman tv has moved to azerspace1 46e.You should concentrate on that sat than turksat for now.If you are willing to enjoy free EPL with free biss.

olenyi: If it has never been able to bring the dish back and a 2.4 mesh for that matter, then something is wrong. Ur telephone wire, how genuine is it? Did u join it somewhere? How far is the positioner from the jack?

These are some of the culprits. Either u got a substandard telephone wire, or its so lenghty that their's some power loss along the line (still caused by low quality wire). Or dat u joined the wire somewhere.

Also try loosening the neck a bit (the big 24/27 inch pivot bolt). Could be too tight.

2.4 mesh dish is one of the lightest around and because of its unique neck design, can be driven by any jack.

Anyway, heavy duty jack are around 7-10k. And u might have to place an order with ur dealer if u're not in Lagos.

Regards.

olenyi: Because of wear and tear and rusting, must times after a while, jacks stop being able to bring a dish back from nss22 position. Dis is expected. Dis mostly happens if u're using a pan dish like 1.8. The solution is 1) make sure ur means outlet is supplying enough voltage to ur positioner. 2) try greasing/lessening the neck of the dish a bit. Or u could go for a heavy duty jack. Or stop going down to 22'w entirely.

If the jack can't go down even when u hand roll it, then theirs a mechanical fault somewhere. Try finding this out.

Then finally try this. Bring down the jack and using the manuel button, extend it out (Like ur driving it to the west) until it gets to some point. ( Remember to hold it so that the inner shaft doesn't go rotating). Use ur hand and roll it in about ten times. Use the manual button to drive it out again (always hold the inner shaft). Repeat this again.

Now go down like u're driving to east until it shows E2. U should notice dat it most have gone well below where it used to stop. Try rolling it in with hand now. If it sticks again, go to west and repeat the above procedure until it can go all the way in.

NB: u should only do this if the fault is not from a mechanical fault like a bent tube, etc.


Tanx boss4 ur selfless service........I am usin a 2.4m mesh dish...d jack has never been able 2 bring back my dish effectively frm nss since I bought and fix it...pls how much does a more powerful actuator cost cuz I bought this 3,000naira.........then as 4 d rotatin fault I wil try nd do what u said I shud do dis mornin and gv u feed back
Regards.

olenyi: When u roll the jack in with ur hand till it stop, just unwind it 2 times, 1, 2. And fix to ur dish. Also look at ur dish to see if anything is blocking the dish from going down near the neck.

Also use the manual button to rotate till u get ''E2'' as u might have set the number 1 button or the start point a bit high.

Ps; its hard for a jack to go down below intelsat 20. Most times if I want a sat dat is below intelsat 20, what I do is to incline the pole a bit forward to the east while casting. This also has the disadvantage of making it hard to get some ''west'' sats.

Regards.