Pipedraft's Posts
Nairaland Forum › Pipedraft's Profile › Pipedraft's Posts
1 2 3 4 5 6 7 8 ... 10 11 12 13 14 15 16 17 18 (of 20 pages)
 Certification And Training Adverts › Relevant Oil/gas Software Training 4 Jobseekers by pipedraft(op): 4:54pm On Jul 07, 2017 |
Geoken Tech Services Nig Limited: is a incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are the Important software application use in the industry. Courses COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee To book for training call Geoken Tech  08060360538/08028553955)kengeotech@yahoo.com Training centres: 8, Omotayo Bello Close, Thomas Estate, Ajah Lagos Mainland Office: 26, Ikotun Rd, College Bustop, opp Domino Pizza Ikotun- Lagos |
| Career › Re: PDMS, Piping Designers And Piping Engineers: Lets Connect Here. by pipedraft: 5:09pm On Jul 06, 2017 |
In Getting PDMS AVEVA Software, as same time applying the software for Plant design, contact Geoken Tech ( 08060360538) |
| Career › Petrel Shlumberger Training In Lagos ( Siesmic/well Logging) by pipedraft(op): 3:46pm On Jul 03, 2017 |
SEISMIC & WELL LOG INTERORETATION (PETREL) COURSE MODULE office: 8, Omotayo Bello Close, Thomas Estate, Ajah/ Ikotun centre Mainland Office: 26, Ikotun Road, College Bstop/opp Domino Pizza, Suite 15, Kazam Plaza, Ikotun-Lagos. CALL: GEOKENTECH: (08060360538/08028553955) kengeotech@yahoo.com •* UNDERSTANDING OF GEOLOGY OF NIGER DELTA •* PETROLEUM SYSTEMS •* INTERPRTATION & MANUAL CORRELATION OF LOGS (GAMMA, RESISTIVITY, DENSITY, NEUTRON) •* SEISMIC SECTION MANUAL INTERPRATION •* CHECK SHOT CORRELATION (OWT VS TVD) •* FAULTS, HORIZONS PICKING MANUALY ON SEISMIC SECTION •* MAP CREATION • * DATA IMPORTATION (SEISMIC, WELL DATAS (WELL HEADS, LOGS) INTO • PETREL •* PERFORMING QA/QC ON AVAILABLE DATAS BEFORE INTERPRETATION •* WELL LOG CORRELATION WITH PETREL: ASSIGN WELL TOPS, PICKING • HORIZON * LOADING OF SEISMIC DATA INTO PETREL (SEG Y DATAS) •* PERFORMING SYNTHETIC SEISMOGRAM (SEISMIC-WELL TIE) •* FAULT & HORIZON MAPPING * GENERATING SURFACE MAP/ATTRIBUTE MAPS •* PROSPECT IDENTIFICATION • * VOLUMETRIC ANALYSIS TARGET AUDIENCE: GEOLOGIST/GEOPHYSICIST, PET ENGINEERS/RESERVOIR ENGINEERS, WELL ENGINEERS, JOBSEEKERS, NYSC MEMBERS • •
|
| Certification And Training Adverts › Training On Cad, Piping, Reservoir Simulation In Ikeja(july Batch) by pipedraft(op): 3:55pm On Jun 22, 2017 |
OIL & GAS SOFTWARE APPLICATION TRAINING IN IKEJA(JULY BATCH) Geoken Tech is organizing training in the following Engineering design, Piping & Reservoir Simulation software: 1. AUTOCAD – All field of Engineering/Sciences 2. PDMS(PLANT DESIGN MANAGEMENT SYSTEM) – for Mechanical, Chemical, Material/Metallurgical graduates, 3. PETREL(SEISMIC & WELL LOGGING)-for Geologist, Petroleum Engineers graduates/Nysc Members N.B: Software’s/EBooks’, Training manual will be given to participant. Interested participant should send Names, Phone no, Email & software of interest to 08060360538. Target Audience: Mechanical, Civil, Chemical, Petroleum Engineers, Geologist, Jobseekers, NYSC Members, CONTACT: (08060360538, 08028553955) Email:kengeotech@yahoo.com DATE: 24th - 28th July, 2017 Fee: #30,000 per course, candidate enrolling for two courses Are to pay #50,000 Training Centre/Venue: Glass House (1, ADEGBEYEM STREET, OFF ALLEN AVENUE, BEHIND ALADE MARKET, IKEJA, LAGOS. |
| Certification And Training Adverts › Oil/gas Software Training In Progress(cad, Pdms, Petrel) by pipedraft(op): 5:44pm On Jun 19, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement • Introduction to AutoCAD 2d Toolbar • Application of Tools bar( draw, modify, object snap, Properties, Status, Command) • Setting AutoCAD drawing Limits • Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc • Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) • Introduction to Isometric drawing • Drawing, dimensioning and editing Isometric drawing • Introduction to AUTOCAD 3D • AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) • Creating solid object with AutoCAD 3d tools • Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools • Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: •Introduction to Plant Equipments type •Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. •Taking coordinate/Equipments position from plant plan drawing (GAD) •Using the Primitive method to design Equipments •Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) •Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc •Piping Setting •Pipe specification in PDMS •Pipe Routing (Linking equipments with pipes) •Modifying the Head/Tail of a Pipe •Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: •Introduction to Aspen Hysys •Hysys working Environment •Adding component to workflow •Adding Fluid package •Entering Hysys Simulation Environment •Adding material and Energy stream •Building Simulation •Analyze the Property Using case Study •Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) •Equilibrium Reaction •Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: • Introduction to P&ID workspace • P&ID Tools Palette • Creating a New P&ID Project • Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space • Connecting Equipments together with Process line • Assigning Tags to Equipments and Specification to process lines • Placing control instruments to process lines, Equipments and on control valves • Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com • Training Manuals & Certificate of Completion will be issue Training Calender: AUTOCAD & PDMS: (June 26th –july 7th 2017) PETREL (SEISMIC & WELL LOGGING) ( June 29th- july 4th 2017) TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA |
| Certification And Training Adverts › Training For Job/career Oppurtunity ( Petrel, Pdms, Cad) by pipedraft(op): 4:47pm On Jun 18, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement • Introduction to AutoCAD 2d Toolbar • Application of Tools bar( draw, modify, object snap, Properties, Status, Command) • Setting AutoCAD drawing Limits • Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc • Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) • Introduction to Isometric drawing • Drawing, dimensioning and editing Isometric drawing • Introduction to AUTOCAD 3D • AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) • Creating solid object with AutoCAD 3d tools • Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools • Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: •Introduction to Plant Equipments type •Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. •Taking coordinate/Equipments position from plant plan drawing (GAD) •Using the Primitive method to design Equipments •Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) •Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc •Piping Setting •Pipe specification in PDMS •Pipe Routing (Linking equipments with pipes) •Modifying the Head/Tail of a Pipe •Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: •Introduction to Aspen Hysys •Hysys working Environment •Adding component to workflow •Adding Fluid package •Entering Hysys Simulation Environment •Adding material and Energy stream •Building Simulation •Analyze the Property Using case Study •Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) •Equilibrium Reaction •Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: • Introduction to P&ID workspace • P&ID Tools Palette • Creating a New P&ID Project • Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space • Connecting Equipments together with Process line • Assigning Tags to Equipments and Specification to process lines • Placing control instruments to process lines, Equipments and on control valves • Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com • Training Manuals & Certificate of Completion will be issue Training Calender: AUTOCAD & PDMS: (June 26th –july 7th 2017) PETREL (SEISMIC & WELL LOGGING) ( June 29th- july 4th 2017) TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA
|
| Career › Relevant Oil/gas Softwares In Oil & Gas Firms by pipedraft(op): 4:16pm On Jun 16, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement • Introduction to AutoCAD 2d Toolbar • Application of Tools bar( draw, modify, object snap, Properties, Status, Command) • Setting AutoCAD drawing Limits • Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc • Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) • Introduction to Isometric drawing • Drawing, dimensioning and editing Isometric drawing • Introduction to AUTOCAD 3D • AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) • Creating solid object with AutoCAD 3d tools • Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools • Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: •Introduction to Plant Equipments type •Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. •Taking coordinate/Equipments position from plant plan drawing (GAD) •Using the Primitive method to design Equipments •Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) •Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc •Piping Setting •Pipe specification in PDMS •Pipe Routing (Linking equipments with pipes) •Modifying the Head/Tail of a Pipe •Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: •Introduction to Aspen Hysys •Hysys working Environment •Adding component to workflow •Adding Fluid package •Entering Hysys Simulation Environment •Adding material and Energy stream •Building Simulation •Analyze the Property Using case Study •Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) •Equilibrium Reaction •Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: • Introduction to P&ID workspace • P&ID Tools Palette • Creating a New P&ID Project • Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space • Connecting Equipments together with Process line • Assigning Tags to Equipments and Specification to process lines • Placing control instruments to process lines, Equipments and on control valves • Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com • Training Manuals & Certificate of Completion will be issue Training Calender: AUTOCAD & PDMS: ( 19th - 24TH june, 2017) PETREL ( SEISMIC & WELL LOGGING) ( 26TH –30th June2017) TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA |
| Career › Acquire Relevant Oil/gas Software Training Skills by pipedraft(op): 5:34am On Jun 12, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement • Introduction to AutoCAD 2d Toolbar • Application of Tools bar( draw, modify, object snap, Properties, Status, Command) • Setting AutoCAD drawing Limits • Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc • Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) • Introduction to Isometric drawing • Drawing, dimensioning and editing Isometric drawing • Introduction to AUTOCAD 3D • AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) • Creating solid object with AutoCAD 3d tools • Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools • Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: •Introduction to Plant Equipments type •Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. •Taking coordinate/Equipments position from plant plan drawing (GAD) •Using the Primitive method to design Equipments •Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) •Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc •Piping Setting •Pipe specification in PDMS •Pipe Routing (Linking equipments with pipes) •Modifying the Head/Tail of a Pipe •Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: •Introduction to Aspen Hysys •Hysys working Environment •Adding component to workflow •Adding Fluid package •Entering Hysys Simulation Environment •Adding material and Energy stream •Building Simulation •Analyze the Property Using case Study •Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) •Equilibrium Reaction •Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: • Introduction to P&ID workspace • P&ID Tools Palette • Creating a New P&ID Project • Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space • Connecting Equipments together with Process line • Assigning Tags to Equipments and Specification to process lines • Placing control instruments to process lines, Equipments and on control valves • Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com • Training Manuals & Certificate of Completion will be issue TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA
|
| Career › Re: Proposal To Train Oil/gas & Engineering Design Staff by pipedraft: 3:29pm On Jun 09, 2017 |
40k per staff |
| Certification And Training Adverts › Oil & Gas Software & Manual Available ( Cad, Piping, Seismic, Well Logging, Hysy by pipedraft(op): 9:45am On Jun 07, 2017 |
OIL & GAS SOFTWARES & TRAINING MATERIALS AVAILABLE IN LAGOS, PH, ABUJA,WARRI, ETC THE FOLLOWING OIL & GAS SOFTWARE ARE AVAILABLE IN ANY PART OF THE COUNTRY 1. AUTOCAD (32/64BITS) 2. PDMS(PLANT DESIGN MANAGEMENT SYSTEM) 3. AUTOCAD P&ID( PIPING & INSTRUMENTATION SOFTWARE) 4. HYSYS(PROCESS DESIGN & OPTIMIZATION 5. STAADPRO ( STRUCTURAL DESIGN & REINFORNCEMENT SOFTWARE) 6. PETREL(SEISMIC RESERVOIR MODELING) 7. WINRESIST/IPIN2( GROUNDWATER EXPLORATION-GEOPHYSICAL SURVEY) 8. DRILLING, PETROPHYSIC, WELL LOGGING MANUALS & MATERIALS N.B: 1, 2, 3-------FOR MECHANICAL, CIVIL, MATERIAL & MATTERLLURGICAL ENGINEERS, PURE/APPLIED SCIENCE 2, 3, 4-----------------CHEMICAL, PROCESS ENGINEERS, CHEMISTRY GRADUATES 1, 5---------------------FOR CIVIL, STRUCTURAL ENGINEERS 6, 7, 8--------------------FOR GEOLOGIST, GEOPHYSICIST, PETROLEUM, RESERVOIR ENGINEERS, UNDERGRADUATES. THE COST OF THE SOFTWARE & TRAINING MANUALS IS #5,000 FOR INDIVIDUALS RESIDING OUTSIDE LAGOS DUE TO COST OF SHIPMENT TO LOCATIO #3,000 FOR INTERESTED WILLING TO COME TO OUR OFFICE @ 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH OR, 26, IKOTUN RD, COLLEGE BSTOP, SUIT 15, KAZAM PLAZA, BY DIAMOND BANK GEOKENTECH (08060360538, 08028553955) kengeotech@yahoo.com AC NO( DIAMOND= 0048195846), OR GTB= 0222052358( Udoh Kenneth) |
| Certification And Training Adverts › Geotechnical/geophysical Survey Training In Lagos by pipedraft(op): 3:45pm On Jun 03, 2017 |
COURSE MODULE FOR GEOTECHNICAL/GEOPHYSICAL TRAINING 1. Objective of site geotechnical site investigation 2. Reconnaissance 3. Preliminary Investigation 4. Detail (In-situ Investigation) 5. Application of Geotechnical site investigation methods (DCPT, SPT, MOISTURE CONTENT, SHEAR STRESS TEST, PERMEABILITY TEST). 6. Geophysical borehole survey- Resistivity (VES)---Software application( Win RESIST, IPin2win)----Application of 1D,2D & 3D Geophysical methods for Groundwater Exploration 7. Resistivity data Interpretation and Application( Data loading, Software program interface, data preparation and organization) 8. Basic Concept of contouring and application 9. 3D Surface mapping and application 10. On Field exposure. 11. In-situ Result analysis/Interpretation 12. Geotechnical software application. 13. PIT Testing procedures & Result interpretation. Training fee: #50,000 Who should attend: Geologist/Geotechnical, Civil Engineers, Environmental Engineers, Hydro geologist, Geophysicist. Contact: Geoken Tech Services Nig Ltd kengeotech@yahoo.com 08060360538/08028553955 Address: 26, Ikotun/Idimu Road, Opposite Domino Pizza Ikotun, Lagos |
| Certification And Training Adverts › Re: Seismic & Well Logging Training ( Manual/software) Interpretation by pipedraft(op): 8:46am On Jun 02, 2017 |
Lecture start Monday June 12th, 2017 |
| Certification And Training Adverts › Geotechnical/geophysical Survey Training In Lagos by pipedraft(op): 2:52pm On May 31, 2017 |
COURSE MODULE FOR GEOTECHNICAL/GEOPHYSICAL TRAINING 1. Objective of site geotechnical site investigation 2. Reconnaissance 3. Preliminary Investigation 4. Detail (In-situ Investigation) 5. Application of Geotechnical site investigation methods (DCPT, SPT, MOISTURE CONTENT, SHEAR STRESS TEST, PERMEABILITY TEST). 6. Geophysical borehole survey- Resistivity (VES)---Software application( Win RESIST, IPin2win)----Application of 1D,2D & 3D Geophysical methods for Groundwater Exploration 7. Resistivity data Interpretation and Application( Data loading, Software program interface, data preparation and organization) 8. Basic Concept of contouring and application 9. 3D Surface mapping and application 10. On Field exposure. 11. In-situ Result analysis/Interpretation 12. Geotechnical software application. 13. PIT Testing procedures & Result interpretation. Training fee: #50,000 Who should attend: Geologist/Geotechnical, Civil Engineers, Environmental Engineers, Hydro geologist, Geophysicist. Contact: Geoken Tech Services Nig Ltd kengeotech@yahoo.com 08060360538/08028553955 Address: 26, Ikotun/Idimu Road, Opposite Domino Pizza Ikotun, Lagos |
| Certification And Training Adverts › Seismic & Well Logging Training ( Manual/software) Interpretation by pipedraft(op): 11:44am On May 31, 2017 |
Seismic Interpretation & Well Logging Training Using Petrel Geoken Tech offering subsidized Geoscience Training on Seismic and Petrophysical interpretation using PETREL Venue: 8, Omotayo Bello Close, Thomas Estate –Ajah, Lagos State. OR 26, Ikotun Rd, College Bustop, Suite 15, Kazam Plaza. COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using checkshot data. •Calculation of petrophysical parameters •Generation of various attributes maps •Identification of prospects. Time: 10am-2pm daily NB: The softwares shall be installed during the training for all participants. Cost: #40,000 For registration and enquiry contact 08060360538 Wassap ( 08060360538)
|
| Career › Oil/gas Softwares Training Manual Up For Grabs by pipedraft(op): 11:16pm On May 30, 2017 |
OIL & GAS SOFTWARES & TRAINING MATERIALS AVAILABLE IN LAGOS, PH, ABUJA,WARRI, ETC THE FOLLOWING OIL & GAS SOFTWARE ARE AVAILABLE IN ANY PART OF THE COUNTRY 1. AUTOCAD (32/64BITS) 2. PDMS(PLANT DESIGN MANAGEMENT SYSTEM) 3. AUTOCAD P&ID( PIPING & INSTRUMENTATION SOFTWARE) 4. HYSYS(PROCESS DESIGN & OPTIMIZATION 5. STAADPRO ( STRUCTURAL DESIGN & REINFORNCEMENT SOFTWARE) 6. PETREL(SEISMIC RESERVOIR MODELING) 7. WINRESIST/IPIN2( GROUNDWATER EXPLORATION-GEOPHYSICAL SURVEY) 8. DRILLING, PETROPHYSIC, WELL LOGGING MANUALS & MATERIALS N.B: 1, 2, 3-------FOR MECHANICAL, CIVIL, MATERIAL & MATTERLLURGICAL ENGINEERS, PURE/APPLIED SCIENCE 2, 3, 4-----------------CHEMICAL, PROCESS ENGINEERS, CHEMISTRY GRADUATES 1, 5---------------------FOR CIVIL, STRUCTURAL ENGINEERS 6, 7, 8--------------------FOR GEOLOGIST, GEOPHYSICIST, PETROLEUM, RESERVOIR ENGINEERS, UNDERGRADUATES. THE COST OF THE SOFTWARE & TRAINING MANUALS IS #5,000 FOR INDIVIDUALS RESIDING OUTSIDE LAGOS DUE TO COST OF SHIPMENT TO LOCATIO #3,000 FOR INTERESTED WILLING TO COME TO OUR OFFICE @ 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH OR, 26, IKOTUN RD, COLLEGE BSTOP, SUIT 15, KAZAM PLAZA, BY DIAMOND BANK GEOKENTECH (08060360538, 08028553955) kengeotech@yahoo.com AC NO( DIAMOND= 0048195846), OR GTB= 0222052358( Udoh Kenneth) |
| Certification And Training Adverts › Re: Seismic & Well Logging Interpretation Training (petrel) by pipedraft(op): 6:34pm On May 26, 2017 |
Seismic & well logging ( Formation Evaluation) training still on contact Geoken Tech. 08060360538. |
| Career › Training For Jobseekers, Trainee/graduate Engineers by pipedraft(op): 2:59pm On May 24, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement Introduction to AutoCAD 2d Toolbar Application of Tools bar( draw, modify, object snap, Properties, Status, Command) Setting AutoCAD drawing Limits Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) Introduction to Isometric drawing Drawing, dimensioning and editing Isometric drawing Introduction to AUTOCAD 3D AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) Creating solid object with AutoCAD 3d tools Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: ·Introduction to Plant Equipments type ·Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. ·Taking coordinate/Equipments position from plant plan drawing (GAD) ·Using the Primitive method to design Equipments ·Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) ·Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc ·Piping Setting ·Pipe specification in PDMS ·Pipe Routing (Linking equipments with pipes) ·Modifying the Head/Tail of a Pipe ·Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: ·Introduction to Aspen Hysys ·Hysys working Environment ·Adding component to workflow ·Adding Fluid package ·Entering Hysys Simulation Environment ·Adding material and Energy stream ·Building Simulation ·Analyze the Property Using case Study ·Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) ·Equilibrium Reaction ·Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: Introduction to P&ID workspace P&ID Tools Palette Creating a New P&ID Project Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space Connecting Equipments together with Process line Assigning Tags to Equipments and Specification to process lines Placing control instruments to process lines, Equipments and on control valves Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com Training Manuals & Certificate of Completion will be issue TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA
|
| Career › Re: Training Calender For Autocad, Pdms, Hysys, Petrel by pipedraft(op): 10:29am On May 23, 2017 |
Hi, Aspen Hysys full version is available. 3k for Lagos residence, 5k for outside Lagos residence because of shipment fee, Thanks. |
| Certification And Training Adverts › Seismic & Well Logging Interpretation Training (petrel) by pipedraft(op): 3:14pm On May 19, 2017 |
Seismic Interpretation & Well Logging Training Using Petrel Geoken Tech offering subsidized Geoscience Training on Seismic and Petrophysical interpretation using PETREL Venue: 8, Omotayo Bello Close, Thomas Estate –Ajah, Lagos State. OR 26, Ikotun Rd, College Bustop, Suite 15, Kazam Plaza. COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using checkshot data. •Calculation of petrophysical parameters •Generation of various attributes maps •Identification of prospects. Time: 10am-2pm daily NB: The softwares shall be installed during the training for all participants. Cost: #40,000 For registration and enquiry contact 08060360538 Wassap ( 08060360538)
|
| Jobs/Vacancies › Training For Jobseekers, Nysc Members, Graduate Engineers In Ajah/lekki by pipedraft(op): 4:38pm On May 15, 2017 |
Geoken Tech Services Nig Limited: is an incorporated company, that is into training of relevant oil/gas, Engineering design software’s. Below are following courses in which we train. Course Specification: COURSE TARGET AUDIENCE 1 AUTOCAD (2D/3D) Mechanical, Electrical, Material & Metallurgical Engineers/Trainee, NYSC Members, Jobseekers 2 PIPING DESIGN (PDMS) Mechanical, Chemical, Process Engineers/Trainee, NYSC Members, Jobseekers 3 PROCESS DESIGN & OPTIMIZATION(HYSYS) Process, Chemical Engineers/Trainee Engineers, Jobseekers 4 RESERVOIR MODELING & WELL LOGGING(PETREL) Geologist, Reservoir Engineers, Geophysicist, Well Engineers Well site Geologist /Graduate trainee 5 PIPING &INSTRUMENTATION DESIGN (P&ID) Mechanical, Process, Electrical/Instrumentation Engineers/Graduate trainee COURSE MODULES ( AUTOCAD 2D/3D) Title: Engineering Design, Drafting & Modeling Overview: the course is design for student to have in depth knowledge to Engineering design and Procurement • Introduction to AutoCAD 2d Toolbar • Application of Tools bar( draw, modify, object snap, Properties, Status, Command) • Setting AutoCAD drawing Limits • Using AutoCAD tools to draw circles, Polygon, Eclipse, Rectangle etc • Modifying AutoCAD outline( using Trim, Extend, copy, move, break etc) • Introduction to Isometric drawing • Drawing, dimensioning and editing Isometric drawing • Introduction to AUTOCAD 3D • AutoCAD 3D Tools( Solid Editing, View, Modeling, View Style) • Creating solid object with AutoCAD 3d tools • Using the Extrude, Sweep, Revolve, Loft, 3D Rotate tools • Rendering of Solid objects FIG 1: AUTOCAD DRAFTING & DESIGN FIG 2: 3D MODELING 2. PETREL (SEISMIC & WELL LOGGING INTERPRETATION) COURSE MODULES •Basic theory of seismic reflection prospecting method in oil and gas. Petrel Introduction & Interface •Different types of well logs and their uses. •Loading of 3D seismic reflection data, making Surfaces & Horizon Seismic Visualization & QC •Picking of faults (Importing fault data/Fault modeling) •Loading of well logs Importing well heads, well deviation & well tops •Seismic-to-well tie using synthetic seismogram •Mapping of reservoirs tops and base • Generation of depth structures map using check shot data. •Calculation of petro physical parameters •Generation of various attributes maps •Identification of prospects. FIG 3: WELL CORRELATION, SEISMIC WELL TIE WITH PETREL 3. PIPING DESIGN & DRAFTING (PDMS) COURSE MODULE: •Introduction to Plant Equipments type •Application of PDMS in Equipment design (Vessels, Pumps, Tanks, Reboiler, Fractionating columns. •Taking coordinate/Equipments position from plant plan drawing (GAD) •Using the Primitive method to design Equipments •Modification/ sizing of Primitives (Cylinder, Nozzles, Manhole) •Application of PDMS in piping components design/Fittings (Elbows, Tee, Flange, Gasket) etc •Piping Setting •Pipe specification in PDMS •Pipe Routing (Linking equipments with pipes) •Modifying the Head/Tail of a Pipe •Supporting Plant with Structures (Beams, Columns, Slab) FIG 4: EQUIPMENT DESIGN & PIPE ROUTING WITH PDMS 4. PROCESS DESIGN & OPTIMIZATION (ASPEN HYSYS) COURSE MODULE: •Introduction to Aspen Hysys •Hysys working Environment •Adding component to workflow •Adding Fluid package •Entering Hysys Simulation Environment •Adding material and Energy stream •Building Simulation •Analyze the Property Using case Study •Modeling Unit Operator (Pumps, Compressor, Expander, Heat Exchanger, Flash Separators) •Equilibrium Reaction •Working on Hysys Project 5. PIPING & INSTRUMNETATION DESIGN/DIAGRAM (P&ID) COURSE MODULE: • Introduction to P&ID workspace • P&ID Tools Palette • Creating a New P&ID Project • Inserting Equipments (Vessels, Tanks, Heat Exchanger, Columns, Pumps) into P&ID Work space • Connecting Equipments together with Process line • Assigning Tags to Equipments and Specification to process lines • Placing control instruments to process lines, Equipments and on control valves • Checking for Errors by running validation FIG 5: PIPING & INSTRUMNETATION DETAILS OF FLOW LINES, CONTROL INSTRUMENTS For Enquiry, Contact: Geoken Tech Services Nig Ltd 08060360538, 08028553955 Email: kengeotech@yahoo.com • Training Manuals & Certificate of Completion will be issue TRAINING CENTRES: 8, OMOTAYO BELLO CLOSE, THOMAS ESTATE, AJAH-LAGOS( ALONG ABRAHAM ADESANYA RD) OUTLET( CENTRE 2): 26, IKOTUN RD, SUIT 15, KAZAM PLAZA, OPP DOMINO PIZZA
|
| Jobs/Vacancies › Vacancy For Industrial Attachmenet Student by pipedraft(op): 4:14pm On May 12, 2017 |
VACANCY: VACANCY:: VACANCY:: OND/BSC IT STUDENT)Geoken Tech: is seeking the service of an interested Industrial attachment student to undergo his/her IT in our company. Qualification: Engineering/Geology/Geophysics Background 2. Most posses a functioning Laptop 3. Residing within Ikotun/Cele Egbe, Egbeda and its Environs Interested student should forward application and indicating course of study to kengeotech@yahoo.com or call 08060360538 Resumption date: As soon as Possible |
| Certification And Training Adverts › Geotechnical/geophysical Survey Training In Lagos by pipedraft(op): 4:17pm On May 09, 2017 |
COURSE MODULE FOR GEOTECHNICAL/GEOPHYSICAL TRAINING 1. Objective of site geotechnical site investigation 2. Reconnaissance 3. Preliminary Investigation 4. Detail (In-situ Investigation) 5. Application of Geotechnical site investigation methods (DCPT, SPT, MOISTURE CONTENT, SHEAR STRESS TEST, PERMEABILITY TEST). 6. Geophysical borehole survey- Resistivity (VES)---Software application( WinRESIST, IPin2win) 7. On Field exposure. 8. In-situ Result analysis/Interpretation 9. Geotechnical software application. 10. PIT Testing procedures & Result interpretation. Who should Attend: Geologist/Geotechnical, Civil Engineers. Contact: Geoken Tech Services Nig Ltd kengeotech@yahoo.com 08060360538/08028553955 Address: 26, Ikotun/Idimu Road, Opposite Domino Pizza Ikotun, Lagos |
1 2 3 4 5 6 7 8 ... 10 11 12 13 14 15 16 17 18 (of 20 pages)