₦airaland Forum

Nafizzey:
and Nigcomsat can easily be added to the set up on top right?

Nigcomsat degree difference from 16E is far about 26.5° which will make it difficult or impossible to get. But if you are good in installation you can use 28.2°E as primary, 16°E below and 42.5°E (Nigcomsat) above. Or else you need another dish for 33°E and 42.5°E while 16°E, 28.2°E and 7°E will be on one dish.

Nafizzey:
Thank you, that's a 90cm dish right? and the Lnbf skew from the picture for 16°E is 7 o clock right?

It's 90cm but you can equally use 60cm. The primary Lnb is 7 O'clock, 28.2E is 8 O'clock, 7E is 8 O'clock.

Nafizzey:
please can I see the picture of 16°E set up as primary?

I don't have a clearer picture but I think I have posted clearer picture in the past on this thread those days, but you can use this picture as a guide.

mahkanjuh:
Please, house, easiest way to attach 16east to multi tv, 28east is the primary

Set 16e as primary and then 28e about 3 to 4inches above the primary Lnb to the left while facing the dish and Lnb position at 7 O'clock for 16e and 8 O'clock for the attachment.

Pidivine:
This set up is not that easy. I think it depends on the location. There was a location I went to in Abuja and to my surprise I wanted to get 28 east and ended up get the two satellites position with a single LNBF i.e New MYTV and JOYTV showing at this same time with a single LNBF.

I moved a bit to another house in that same location and used 28 east as Primary and just dropped the second second LNBF on the 28 east and got 16 east no stress.

This set up will only be easy if you use 12525V30000 for 28 east

How true or possibly for a satellite of far degree apart to be received on a single lnb if not motorized. Or I don't understand what you mean? 51.5e and 28.2e are 23.3° apart so both can work as an attachment or the dish is motorized.

sunene1:
Inverto ultra black proofed once again to be one of the best LNB by delivering all cosmote channels even difficult cosmone 1&2 come up at a particular time of d day and dissapear at a particular time also on 9e on a 2.4m dish location Abuja-Nigeria.I think I will upgrade my dish to 3m upwards because of DSTV.

Please where did you get the lnb?

Spy360:
Howdo you track Abs 3w using 28e as reference. Who knows abeg talk. Thanks.

Abs3 is 3w, so from 28e move your dish as if you are going backward

lamtam0:
I just bought dual way stargold lnb original one last week #9500 from one of trusted guru and is perform on both V and H on my 3m both on 9e and 13e and mind u to differentiate between original and fake stargold is difficult so don't just buy any one. is this forum I met on guy that sell 4way stargold fake for me if not d customer believe in me I will pay d money back.

Can we chat on WhatsApp.
080 six 7 six 5 two 6 three 9 is my number.

jovial4real:
Ok, thanks
How about GTMEDIA Satellite finder, can you recommend any store were I can get it.
I guess it is expensive trying to buy from Aliexpress.

I am using it, it is very good and effective. I bought mine from AliExpress but I hard someone in this forum saying that it can be gotten from Lagos also.

lamtam0:
technomate av single way is around 7k upward but no double way in d market for now.

Thanks

GeorgeD1:
I'm not aware of any satellite outlet selling that LNB for now except you want to order it direct
from Ebay. However, you can consider using technomate 4-way lnb (TM4) as someone already
suggested. Stargold 4 way lnb is also good.

Thanks. Is the technomate or not having single way? And what is the price range?

lamtam0:
why not go for technomate or star gold original

What is their signal conversation rate?

@GeorgeD1 and the house, where can I get Inverto black ultra lnb to improve my weak signal reception.

Ifeanyi4491:
do you have wifi stick

Are you living in Abuja for the Wi-fi stick.

harizonal123:
Pls how is this device used

It's used with phone, it's very effective but must be used with power bank that supplies at least 2.1A and above or phone charger of 2A and above. That is what I have been using since 2018.

Good morning all. Happy Easter celebration! Please anyone with strong 4950 patch software should help and send it to my WhatsApp number at 080-6765-two-6-three-9.

zeanslim:
Not reachargable, DC fan

From the spec of your fan, it is around 19.2watt

spartacus11:
Come and build for me oga. Lets talk i love ur set up

Call me on 080-six-7-six-52-six-three-9.

godspeed:
Please enlighten me more on this

Every charge controller has a maximum power it can handle. In your case you have 4x150=600 watts already and is 12v system which I think is maximum your charge controller can handle. If you are adding another panel, change or add another charge controller.

solasola:
l use the exact pwm cc u have. from what I see, it records just PV Ah input only. I have 4 12v/150w panel in parallel. I use my system for 24hrs. I mean inverter for 13hrs for charging business and run off Dc loads through the night. my 2 100ah in parallel never drops below 50%dod. my harvest has not been impressive though. I get a least above 50ah on less sunny days and abt 150Ah on very sunny days. Ideally, that for me is too low. I would be adding at least two more panels asap.

Remember that you have 600watts panel already! Check the maximum your charge controller can handle or add another charge controller or increase the capacity of your charge controller.

funshyboi:
But I'm currently using the mtn 80watts solar panel directly on thesame battery for the past 13months and the battery is still intact

I believe the battery you are joking with is lithium phosphate battery. It can explode at any time.

Veniscy:
I'm in sun city galadimawa

Contact: 08067652639

Veniscy:
edakun any installer in Abuja that can help with my nigcomsat that is showing no signal for close to a month after paying someone to do it for me it worked for only week. please help a sister.

Which side of Abuja are you? Am in Nyanya axis, Jikwoyi.

unikazzy:
Thank u so much -----God bless

Don't go for collective because;
1. Sometimes you may not even be able to show the three matches you anticipated cos they may air matches on channels that are paired on a particular decoder. I have a friend who is suffering from that right now.
2. You will not have any other channels again except sports
3. You can't change back to extra view unless they confirmed that you no longer operates the viewing center.
4. Apart from champions League and during Christmas period you hardly have three important matches air simultaneously because of TV broadcast right.
My suggestion is for to buy another decoder and subscribe compact when you need it. Or if you have stable data connection in your area buy android decoder that is compatible with D*TV now app and activate for the third view when ever you need it buy small data and use for that day.

Donsco:
I didn't know this Lifepo4 batteries can be connected in series.
I know this battery is rated 5a 14.6v but how come you use 40a Charge controller. Abeg abi novice o. Wanna understand.

My panel is just 250watts only so can not deliver up to 40a, is just an oversized.

Topmost11:
My current pwm cc has 3 terminals viz: PV, battery and load which I don't use since load is connected via inverter to battery.

This new mppt cc also has 3 terminals: pv, battery and load.

What do I connect to the load of the new cc? Do I ignore as before or connect load to it. I think the terminal is for direct DC loads but I need clarification/confirmation.
Pix attached is the result of my tinkering at about 6.45 this morning but I have reverted to the pwm cc pending response to my queries. It started with 12.7v 0a and moved to 15.1v 0a and was indicating panel is charging before I disconnected it. Thanks.

The load connection is just for light like street light, which I used mine as under voltage cutoff.
Your system is 12volt system that is why it's indicated 15.1 volt for over voltage cutoff but I will advise you to check your battery maximum charging voltage and reset the 15.1v, that 12.7v should not boarder you because you are not using the load terminals it is for under voltage reconnection.

mank1234:
Putting up a disconnect switch for an ac to come on when battery voltage reaches 54V and disconnects when it drains to 50V.

Are you using solar charge controller? Then you can use the charge controller with relay

mank1234:
Saw SSR but limited to 32V. Trying to see if I can eliminate the need for buck down converter. The clients setup is 48V.

For what purpose is is it for?

mank1234:
Hi guys,

Anyone with a link on aliexpress for a contactor with following specification:
-DC control coil of 48V
-Normally open (NO) 220V 63A
?

Thanks in advance.

Check out this!
NGN 3,187.36 5%OFF | TOCT1 2P 63A 220V/230V 50/60HZ Din rail Household ac Modular contactor 2NO or 2NC or 1NO 1NC
https://s.click.aliexpress.com/e/B5uEyDBE and
NGN 4,284.71 5%OFF | TOCT1 4P 63A 220V 400V~ 50/60HZ Din rail Household ac Modular contactor 4NO 2NO 2NC 4NC
https://s.click.aliexpress.com/e/E9DGGLTw

mank1234:
Hi guys,

Anyone with a link on aliexpress for a contactor with following specification:
-DC control coil of 48V
-Normally open (NO) 220V 63A
?

Thanks in advance.

What I see is 3-32DVC, 220volt 10-120A
NGN 1,447.49 11%OFF | SSR -120DD DC control DC SSR 120a dd relay miniature Single phase protection Solid state relay
https://s.click.aliexpress.com/e/o8mXLrVI

Saipro:
I'd like to buy a few units. Any help/link?

I think some one in the forum posted where to buy it, and the cost is #28,000 For the 40AH.

ceaser:
He mentioned having Lithium Polymer batteries. I think that calls for more stringent charging conditions which that SCC may not provide, except if the charging parameters are user customisable.

I think he should avail the forum the voltage of his lithium battery, if it has in built BMS and also if his SCC is customisable.

His batteries are lithium phosphate battery and has BMS in them rated 11-14.6volt
His charging is designed for external using SCC program for over voltage cutoff of 14.6v