fbtowner:



If by “Is your ABS and traction control on” u mean if my abs light is on, the answer is no.

I change the 4 brake pads 3 months ago also.

Thanks I will check all that you mentioned and I will also remove the rubber they used to raise it


What is the best way to raise the car just slightly?

If you must alter the suspension height of your car higher to enable you drive it, pls sell it off and get an SUV.

kingreign:

Yes, the glass alone. E be like you no know wetin dey sup yet for your car.
The non BSM is 50-70k a set.


Your front logo, becareful too, that logo is 25k.

Some people don't know the value of the cars they drive.

Please tell them some side mirrors cost over 1million.

Side mirror for ordinary Peugeot 508 is over 500k.

AutoConsult:

Some people don't know the value of the cars they drive.

Please tell them some side mirrors cost over 1million.

Side mirror for ordinary Peugeot 508 is over 500k.

They don't know.

The 06 Infiniti I drive, had an exhaust leak, I decided rather than go weld it, to get a replacement from the Y pipe down to the muffler tip, guess what?
It cost 180k.
I kuku humble myself, go weld am back.

kingreign:


They don't know.

The 06 Infiniti I drive, had an exhaust leak, I decided rather than go weld it, to get a replacement from the Y pipe down to the muffler tip, guess what?
It cost 180k.
I kuku humble myself, go weld am back.

🤣🤣🤣

You can imagine. Had to do it the Nigerian way.

kingreign:


If you must alter the suspension height of your car higher to enable you drive it, pls sell it off and get an SUV.

Thanks a lot. I will remove all the rubber used in raising it and test drive again

AutoConsult:

🤣🤣🤣

You can imagine. Had to do it the Nigerian way.

Baba, dem no dey tell blind man say rain dey fall. 🤣🤣🤣

It'll be thoroughly worth it, I assure you

Hello bosses, my Camry 2003 V4 have Abs issue. It was only the abs light that was blinking yesterday but it has been showing brake light alongside it and stays like that. My rewire pull the abs module out to check and he said it was not communicating that I need to replace it. I don’t know what he means by not communicating.
Pls help me out with what I need to do. Thanks 🙏🏾

Greetings guys, please I need help.
My Toyota Corolla S 2003 model consumes fuel a lot.
I've replaced both catalyst and plugs yet no solution.

I noticed that the idle air control valve is not working and I've replaced it more than 3 yet this idle air valve refuse to work.

I also noticed that my fuel pump is connected directly to ignition

I also noticed that my thermostat has been removed and the fan is on direct ignition. Please somebody should help me

abiolag:
Hello bosses, my Camry 2003 V4 have Abs issue. It was only the abs light that was blinking yesterday but it has been showing brake light alongside it and stays like that. My rewire pull the abs module out to check and he said it was not communicating that I need to replace it. I don’t know what he means by not communicating.
Pls help me out with what I need to do. Thanks 🙏🏾

Tell your rewire to reinstall whatsoever he pulled out. When he reinstall it back, flee from him, go elsewhere and scan it then post codes.

Hello guys, any idea on genuity of Masuma parts being sold in Nigeria?

I have changed my brake discs to tokunbo and then to a brand new one but I'm still getting steering judder when braking on highway speeds (100-140KMh).

I'm thinking on buying an 'oem' or at least legitimate quality as I've changed almost everything (discs, pads, calipers, tierod ends, ball joints, control arm and stabilizer bar bushings, wheel bearings, shaft, tokunbo tires, shock absorbers, even rotated tires) on my front end except the hub itself but I keep, getting the ridiculous vibrations when I dare brake.

Or is there anything I should be looking at? What's the possibility of a tokunbo and brand new brake discs being out of round?

masciv:
Hello guys, any idea on genuity of Masuma parts being sold in Nigeria?

I have changed my brake discs to tokunbo and then to a brand new one but I'm still getting steering judder when braking on highway speeds (100-140KMh)

I'm thinking on buying an 'oem' or at least legitimate quality as I've changed almost everything (discs, pads, calipers, tierod ends, ball joints, control arm and stabilizer bar bushings, wheel bearings, shaft, tokunbo tires, shock absorbers, even rotated tires) on my front end except the hub itself but I keep, getting the ridiculous vibrations when I dare brake.

Or is there anything I should be looking at? What's the possibility of a tokunbo and brand new brake discs being out of round?

Replace the Hub ASSY.

kingreign:


Tell your rewire to reinstall whatsoever he pulled out. When he reinstall it back, flee from him, go elsewhere and scan it then post codes.

He has already put it back and scan but claimed the machine could not read it

abiolag:

He has already put it back and scan but claimed the machine could not read it

Take it elsewhere, scan with a competent scan tool.

kingreign:

Check if your car has been bled properly after water pump replacement, check if water still stay at same level after driving for some time.
As for the sluggish pick up after slowing down, have your car scanned and post codes here.
Undo the rubbish contraption cut and join rubber that mechanic did.
Finally, change mechanic

Many thanks my brother

AutoConsult:

This is strange.

Firstly, Toyota Siena does not use a fan belt. Secondly, there's no way the hub can rest on the serpentine belt and the vehicle will still be mobile.

Now, I don't know what your mechanic did to your shaft. If truly he changed it, there's no way it'll still be making noise, except what is making that sound is actually not the shaft.

Ordinarily, shaft would only make noise during turns, but for It to be making noise while you are moving at 40km/h, that's weird. The shaft must be completely gone, which now brings us back to if your mechanic truly changed the shaft or not.

Some mechanics I know only add lots of grease to reduce the noise - they don't change it.

Now, concerning the steering issues, it's difficult to diagnose steering issues over the phone. It can be tricky at times. You'll probably have to approach a different mechanic to help you check it again. Prepare to change both the pump and the rack at worst.

Generally, I wish you could get a sincere person to help you perform a thorough check on your vehicle's suspensions. Something seems to be bent down there, putting too much pressure on your tire, hence the smelly tire you perceived earlier.

when i said my hub broke and rested on the belt, i was talking about the engine belt. The mechanic worked on the shaft twice and it was still the same. So i believe it might not be the shaft, my guess in ball joit or lower arm go bad due to the imapact i had in the pot hole.
As for the steering i really don't know what to say because it was never there pior to when my hub happened.

24dro:


when i said my hub broke and rested on the belt, i was talking about the engine belt. The mechanic worked on the shaft twice and it was still the same. So i believe it might not be the shaft, my guess in ball joit or lower arm go bad due to the imapact i had in the pot hole.
As for the steering i really don't know what to say because it was never there pior to when my hub happened.

Well diagnosing a vehicle over the phone is not really easy when it requires hearing the sounds it gives.

Only the sound can give a first hint.

AutoConsult:

Well diagnosing a vehicle over the phone is not really easy when it requires hearing the sounds it gives.

Only the sound can give a first hint.

I would be more than happy if you could recommend a good techian for me, stay on the mainland.

I saw this k&n cold intake for lexus es350 and it promises additional 12HP and 13TQ when fitted. I want to add it to my 2010 lexus es350. Is this advisable? Will there be downsides? Can any mechanic help in fixing this for me here in abuja or help me source for it locally here in naija?

kingreign:


Take it elsewhere, scan with a competent scan tool.

Thanks for your input 🙏🏾
I started the car in the afternoon and noticed the abs and brake light were not showing again but door light and cruise light started blinking with airbag light 😀
I called another Rewire who could not even say anything reasonable. I decided to drive the car for like 30 minutes around without Ac and when I put on the Ac after like 45 minutes the car just went off. I start it again and all lights were gone and it became normal again.
I drove for another 2 hours and no light.
Though I washed the engine a day earlier maybe that could be the reason for the malfunctions

24dro:
I would be more than happy if you could recommend a good techian for me, stay on the mainland.

Kindly call 07089030689 for further assistance

abiolag:

Thanks for your input 🙏🏾
I started the car in the afternoon and noticed the abs and brake light were not showing again but door light and cruise light started blinking with airbag light 😀
I called another Rewire who could not even say anything reasonable. I decided to drive the car for like 30 minutes around without Ac and when I put on the Ac after like 45 minutes the car just went off. I start it again and all lights were gone and it became normal again.
I drove for another 2 hours and no light.
Though I washed the engine a day earlier maybe that could be the reason for the malfunctions

You've solved the mystery.

jceesquare:

You've solved the mystery.

Miraculously 😀

abiolag:


Miraculously 😀

You've found out that water is a poor conductor.

abiolag:

Thanks for your input 🙏🏾
I started the car in the afternoon and noticed the abs and brake light were not showing again but door light and cruise light started blinking with airbag light 😀
I called another Rewire who could not even say anything reasonable. I decided to drive the car for like 30 minutes around without Ac and when I put on the Ac after like 45 minutes the car just went off. I start it again and all lights were gone and it became normal again.
I drove for another 2 hours and no light.
Though I washed the engine a day earlier maybe that could be the reason for the malfunctions

It's normal with 1975 TransAm.

jceesquare:

You've found out that water is a poor conductor.

I’ve learnt my lessons. I will only blow my radiator henceforth because that was what I wanted to do but decided to wash the whole engine since is too dirty

abiolag:

I’ve learnt my lessons. I will only blow my radiator henceforth because that was what I wanted to do but decided to wash the whole engine since is too dirty

Just clean the engine with wet rag, that will do.

Good evening everyone, I am having issues with my Camry 2002 v4.
I have been going from one rewire to another. The complain I gave to them is that when I accelerate, sometimes it moves smooth and sometimes it's sluggish.
Coil has been changed, plug changed, engine oil replaced, gear oil replaced, air flow metre replace. But the issue still persists.
Now one of the rewire told me it's not fuel pump, that i will need to change the brain box.

I need help!!

Milestogo:
Good evening everyone, I am having issues with my Camry 2002 v4.
I have been going from one rewire to another. The complain I gave to them is that when I accelerate, sometimes it moves smooth and sometimes it's sluggish.
Coil has been changed, plug changed, engine oil replaced, gear oil replaced, air flow metre replace. But the issue still persists.
Now one of the rewire told me it's not fuel pump, that i will need to change the brain box.

I need help!!

Have you scanned this car?

vivalavida:


Have you scanned this car?

Yes I have,
Like 4 rewires have done that for me. And this same issue continue..
Funniest part is after scanning it will work fine for some days, and comes back again

The engine light also goes off after scanning but after some days when the issue persist again, the engine light comes up.

Milestogo:


Yes I have,
Like 4 rewires have done that for me. And this same issue continue..
Funniest part is after scanning it will work fine for some days, and comes back again

The engine light also goes off after scanning but after some days when the issue persist again, the engine light comes up.

Dem scan ya motor and dem no tell you codes wey dey?

kingreign:


Dem scan ya motor and dem no tell you codes wey dey?

Some say, coil, misfire, airflow metre. Apart from all this, nothing..
And all the coil was changed, airflow metre.

Except for one rewire that told me I need to change the brain box.