foonshur:

do they still sell the zte mf28, does it come unlocked truly, does it really support all 4g networks including glo and have you used it personally? sorry for my many questions

abunafiu2:
This one all of una dey blow grammar..... makes me look like I never attended CCNA classes.
If Bigrovar steps in now... na to scatter d whole thing now.... with his own highTech analogies.

always nice to read some off Solar tips from you guys.
love y'all.

Uncle Dapsyra, oya contribute ya own join d matter too oooo

abunafiu2:
Dear chief GeorgeD, you were about to give us a review of your solar water heater system.
kindly do sir

Saipro:
I apologise for going off topic but I need to solve two problems and need the most efficient way to do it. My personal workaround is largely inefficient. This is the first issue:
I recently acquired a dual-band NetGear router for large homes. It accepts LAN input. I have a MiFi and a Wireless Modem but both have limited coveragein and around the building.

What I want:
A 3G/4G device which accepts a SIM and has LAN output yet won't break the bank.

You can use your netgear router only as wireless acess point to boost coverage from existing mifi - which model do you have ?

https://kb.netgear.com/20927/How-do-I-change-my-NETGEAR-router-to-AP-mode-after-I-ve-already-run-setup
The second issue:
I need a WiFi extender which can plug into the LAN sockets of my Midnite Classics. I recall having read from one or two people here using them (dapsyra comes to mind). I want to use whatever it is you've used which works.

pranil:


https:///wireless-tv-network-adapter-for-wifi-range-extender-3738753 - cheapest I found . will also need a wall plug for 5 V DC ( any of the old mobile chargers) or use dedicated Battery to 5 V converters from Aliexpress

DMerciful:
lexi28

Here is how to resolve the excessive mustpower series temperature issue by changing the position of the temperature sensor so the fan comes on at 40 degrees vs 65degrees.
step 1: Locate the temperature sensor on the heat sink(first picture)
step 2:Increase the length of the temperature sensor wire by adding additional wires so it can reach the transformer
step 3:Loose one nut of the transformer lamination holder and use a big washer to fix the temperature sensor to the transformer as shown(third picture)

whatsapp me for further clarification(see my signature)

lexi28:
I basically want to leave some circuits on solar/inverter backup when PHCN fails without the use of separate DB's.

I am trying to get the simplest way to achieve that without complex rewiring.

Barezzi:
If you already have a 3-phase DB, perfect!
Dedicate one of the phases to Inverter loads, and the other two to PHCN only loads.
Stick a caution sign on your db stating "Dual Power Source Feed", so any electrician will
know to isolate all your power sources before fiddling with ya db.

sinistrian:
Weather has not been very favourable in the last 5 days. I've had to run my (now rusting) generator for a few hours each night to make up the charge.

sinistrian:
Weather has not been very favourable in the last 5 days. I've had to run my (now rusting) generator for a few hours each night to make up the charge.

kiekie1:


Its same here in Lagos state .. Rainy / dull weather days , my gen has been laying dusty though, I just turned on last week for critical heavy loads(water pump,microwave,electric iron) ! We manage our daily loads best way possible for 50% usable out of 14400wh battery bank . Cheer's

nonoski:
Pls where can one buy 300w monocrystalline solar panels here in Port Harcourt.

Trippledots:
hello,

setup A fronius eco is connected in grid tie inverter mode to a three phase victron setup.

observation fronius eco keeps hitting 25kw production and trips off showing an error code which translates to frequency mismatch then fronius starts a cycle of booting which takes almost a minute.

request pls does anyone have experience like this or knowledge about how to tackle this?

temporary fix reduced the panel stream by one so that it doesn't hit that value, but this affects total fronius output esp when sky is overcast. kindly mention me when you advice.


thanks in advance

NoMoreTrolling:

don't know if i should call police for the niggga that sold this shhh to me

NoMoreTrolling:
my gel batteries are dead in just under a year.

talk about depressing

don't know if i should call police for the niggga that sold this shhh to me

kiekie1:
JUST OFFLOADED- CALL US NOW

Yachi 310w mono ...... N57,000
Yachi 260w mono ...... N46,000

Solar world 325w mono panels. Made in Germany
..N80,000 (9 units in bulk)

Contact :
Smartcell global services
081-350-31951

Barezzi:

Hang him from his balls, and use it for target practice!

efuro:


I mentioned about 2 years ago that batteries are the bane of RE in Nigeria.

First check if you're not the primary cause of early battery death because that same battery you claimed died under a year may yet be serving another customer much longer than 2 years.

Channel your anger towards SON and not the deallers. When a whole consignment is destroyed. Inferior batteries will gradually die out. Remember it is easier to get a replacement through SON than to save for new set of batteries which may also be substandard.

It is sad!

NoMoreTrolling:
my gel batteries are dead in just under a year.

talk about depressing

don't know if i should call police for the niggga that sold this shhh to me