₦airaland Forum

glambo:
Had done that now.

Even DD at your place
The blue big daddy guy

What I did of recent is checking the plugs and coil, then firing the nozzles. And check for broken or leaking air hoses. Finally changing the charcoal cannister

Hustling from sunrise to sunset does not guarantee not lacking, stacking hours by grinding is not a recipe for success. So pls drivers on board chill a little and move again.

Like I always say; Hustling don't kill people, Stress kill people.

Fedrams:
Pls help me check this vin no Jtdbr32e160077848

VIN number check is kinda of pay to get sir.

Chat me up on WhatsApp

B-Automobile Nigeria Limited
08055347947

U0100 - Lost Communication With Engine Control Module/Powertrain Control Module

Let's talk about U0100 fault code and how serious this could be.

The PCM/ECU also know as the BRAINBOX, communicate with all other sensitive part of a car architecture to achieve a maximum output.
The ECU/PCM have programmed information about what messages are needed to be exchanged on the serial data circuits.
There two dedicated wires for communication namely CAN High and CAN low, which Carrie's 2.5V and as high as 3.75V. Any interruption between this set standard causes total failure.

Possible Causes

◇ Check for more codes
◇Faulty Engine Control Module (ECM) / Powertrain
Control Module (PCM)
◇ECM/PCM harness is open or shorted
◇ ECM/PCM circuit poor electrical connection

Possible Symptoms

■ Vehicle not starting
■ Check Engine light.

Possible Solutions

When you car throw up this fault code, first inspect the ECM/PCM wiring for any breach, check the connectors. If all is in order remove the ECM/PCM check the pin for bent or rusty pin.
The solution if all is good is to replace the ECM/PCM.

B-Automobile Nigeria Limited
08055347947

U0100 - Lost Communication With Engine Control Module/Powertrain Control Module

Let's talk about U0100 fault code and how serious this could be.

The PCM/ECU also know as the BRAINBOX, communicate with all other sensitive part of a car architecture to achieve a maximum output.
The ECU/PCM have programmed information about what messages are needed to be exchanged on the serial data circuits.
There two dedicated wires for communication namely CAN High and CAN low, which Carrie's 2.5V and as high as 3.75V. Any interruption between this set standard causes total failure.

Possible Causes

◇ Check for more codes
◇Faulty Engine Control Module (ECM) / Powertrain
Control Module (PCM)
◇ECM/PCM harness is open or shorted
◇ ECM/PCM circuit poor electrical connection

Possible Symptoms

■ Vehicle not starting
■ Check Engine light.

Possible Solutions

When you car throw up this fault code, first inspect the ECM/PCM wiring for any breach, check the connectors. If all is in order remove the ECM/PCM check the pin for bent or rusty pin.
The solution if all is good is to replace the ECM/PCM.

B-Automobile Nigeria Limited
08055347947

Wonder where that bae that was active during the locked down was.

Miss her CIA stuff here

izzou:
You won't make heaven, hope you know

Izzou you reach here?

nonhuman:
ok thank you boss, is the solonoid located inside the gear

They are outside the tranny. About two of them and couple of sensors

nonhuman:
My Honda civic 8generation delays to engage revers sometimes, it takes longer till I turn of engine and on again some tines it takes seconds sometimes it will engage normal, but the drive selects and drive well, transmission fluid guaged very well and I am using the recommended Dw1 what could be the problem

Run diagnosis boss, it can be the Solenoid for that.

shollywendy1:
" bishop nwa mama" thumb up

Boss man I still never bring my gift ooo...

shollywendy1:
He said "buy and drive" . He didn't say buy and reverse since the reverse is faulty. Lol

Naso the matter take be now.

gbemsone:
drop ur number to call u or whatsapp me 07066661158

i want to buy the hardex

B-Automobile Nigeria Limited
08055347947

Fedrams:
Good day chairman, pls find below the code I got when I scan my toyota camry
Car Scanner ELM OBD2
DTC report
Selected brand: Toyota

============1==============
P0500
Raw code: 0500
ECU: 10
Status: Confirmed
OBDII: Vehicle speed sensor (VSS) - circuit malfunction
Toyota: Vehicle Speed Sensor Circuit Malfunction
============2==============
P0401
Raw code: 0401
ECU: 10
Status: Confirmed
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============3==============
P0120
Raw code: 0120
ECU: 10
Status: Confirmed
OBDII: Throttle position (TP) switch A/accelerator pedal position (APP) switch A - circuit malfunction
Toyota: Accelerator Pedal Position Sensor / Throttle Position Sensor A Circuit Malfunction
============4==============
P0105
Raw code: 0105
ECU: 10
Status: Confirmed
OBDII: Manifold absolute pressure (MAP) sensor/barometric pressure (BARO) sensor - circuit malfunction
Toyota: Manifold Absolute Pressure / Barometric Air Pressure Sensor Circuit Malfunction
============5==============
P0401
Raw code: 0401
ECU: 10
Status: Pending
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============6==============
P0500
Raw code: 0500
ECU: 10
Status: Confirmed
OBDII: Vehicle speed sensor (VSS) - circuit malfunction
Toyota: Vehicle Speed Sensor Circuit Malfunction
============7==============
P0401
Raw code: 0401
ECU: 10
Status: Confirmed
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============8==============
P0120
Raw code: 0120
ECU: 10
Status: Confirmed
OBDII: Throttle position (TP) switch A/accelerator pedal position (APP) switch A - circuit malfunction
Toyota: Accelerator Pedal Position Sensor / Throttle Position Sensor A Circuit Malfunction
============9==============
P0105
Raw code: 0105
ECU: 10
Status: Confirmed
OBDII: Manifold absolute pressure (MAP) sensor/barometric pressure (BARO) sensor - circuit malfunction
Toyota: Manifold Absolute Pressure / Barometric Air Pressure Sensor Circuit Malfunction

P0500 - Vehicle Speed Sensor - Your Speedometer won't function, erratic transmission shifting.
It is located on the transmission.

P0401 - Exhaust Gas Recirculation -
EGR passage clogged
Faulty EGR Vacuum Modulator Valve
Faulty EGR Valve
Faulty EGR solenoid valve
EGR solenoid valve harness is open or shorted
EGR solenoid valve circuit poor electrical connection
Dead (Weak) battery
Faulty EGR temperature sensor and circuit
Exhaust gas leaks.

It can make the car hesitate or stall.

P0120 - Throttle Position Sensor
Erratic rpm.
Just change the Throttle body.

P0105 - Manifold Absolute Pressure Sensor
Change the MAP Sensor.

If you have any more questions pls get in touch with me on WhatsApp.

B-Automobile Nigeria Limited
08055347947

Fedrams:
I wish but am in Akure.

Ok sir, what do you want me to do sir?

Fedrams:
Good day chairman, pls find below the code I got when I scan my toyota camry
Car Scanner ELM OBD2
DTC report
Selected brand: Toyota

============1==============
P0500
Raw code: 0500
ECU: 10
Status: Confirmed
OBDII: Vehicle speed sensor (VSS) - circuit malfunction
Toyota: Vehicle Speed Sensor Circuit Malfunction
============2==============
P0401
Raw code: 0401
ECU: 10
Status: Confirmed
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============3==============
P0120
Raw code: 0120
ECU: 10
Status: Confirmed
OBDII: Throttle position (TP) switch A/accelerator pedal position (APP) switch A - circuit malfunction
Toyota: Accelerator Pedal Position Sensor / Throttle Position Sensor A Circuit Malfunction
============4==============
P0105
Raw code: 0105
ECU: 10
Status: Confirmed
OBDII: Manifold absolute pressure (MAP) sensor/barometric pressure (BARO) sensor - circuit malfunction
Toyota: Manifold Absolute Pressure / Barometric Air Pressure Sensor Circuit Malfunction
============5==============
P0401
Raw code: 0401
ECU: 10
Status: Pending
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============6==============
P0500
Raw code: 0500
ECU: 10
Status: Confirmed
OBDII: Vehicle speed sensor (VSS) - circuit malfunction
Toyota: Vehicle Speed Sensor Circuit Malfunction
============7==============
P0401
Raw code: 0401
ECU: 10
Status: Confirmed
OBDII: Exhaust gas recirculation (EGR) system - insufficient flow detected
Toyota: Exhaust Gas Recirculation Flow Insufficient
============8==============
P0120
Raw code: 0120
ECU: 10
Status: Confirmed
OBDII: Throttle position (TP) switch A/accelerator pedal position (APP) switch A - circuit malfunction
Toyota: Accelerator Pedal Position Sensor / Throttle Position Sensor A Circuit Malfunction
============9==============
P0105
Raw code: 0105
ECU: 10
Status: Confirmed
OBDII: Manifold absolute pressure (MAP) sensor/barometric pressure (BARO) sensor - circuit malfunction
Toyota: Manifold Absolute Pressure / Barometric Air Pressure Sensor Circuit Malfunction

Got it sir.

It's more explanatory sir... Do you want to fix sir?

chijioke17:
I've contacted him before via WhatsApp, he didn't respond, only read the message, tried the number but it's not reachable

Maybe I will get in touch with him

chijioke17:
Blackbishop, please do you have an idea of the cost of honda civic passenger side air vent and where I can get it please

Call Luvinhubby 08099451504

pope191:
Kaz Baba! More grease from d other side

Just going by d logic of how I read newspaper, I start from sport.

Cool logic

nonhuman:
a scan was ran on the car it showed that the knock sensor is faulty that was what was displayed on the screen

Symptoms of a bad knock Sensor differs from what you posted as the problem. Knock Sensor reduces the engine capacity and the rest.

But from my experience when you have such issue the likely problem is your Throttle body. Do you mind bring it for diagnosis

nonhuman:
Please help my Honda Civic is not idling, it increases acceleration on its own without my input, please help breaking finds it dificult to catch

Run diagnosis first and run Freeze frame as well

radautoworks:
no, I said you are a better option than wasting money on a kazeem or spending "extravagant" amounts at my shop. Why would you even think that's what I said Have you ever seen me just come out and start abusing someone who was jejely minding their business??

Ma'am I will never insinuate that. Was trying to clarify people the read towards a direction and understand upside down now.

radautoworks:
Very well said.

Also, anything we fix we WARRANTY. even when you bring your own parts, our labor is still warrantied for 90 days. And guess what? As more shops open up, any of them will cover your warranty. Break down in ibadan? Covered. Port Harcourt? Covered. Mainland? Covered. Will kazeem do that? You get what you pay for. You haven't even seen the tip of what I'm up to yet.

It's unfortunate some false narratives keep being put out but those who use us have tried the cheap alternative and they know why they come to us. Like one or two people pointed out, no be by force to come. That is why I offered free diagnosis so at least you will know what is wrong before someone tells you rubbish. You are free to fix your car wherever works for you.

When I opened up shop I was very clear this was not about opening a single shop. If that was the case I could have opened something way smaller that cost way less. This was about getting the entire industry to change which required a LOT of noise and we already have. Some dealers have been adjusting their pricing because of us, even some of the techs on NL are now offering guarantees and adjusting how they do things because of us. Kazeems sef are starting to realize customers aren't as gullible as they used to be. That's what I want. A complete shift in the whole industry. What I'm looking at is way bigger than a few shocks here and there. Education. So whoever has an issue with me, please fix your car wherever makes you happy and those who see value in what I'm offering will still come to me.

ENOUGH of mechanics taking advantage of people.

P.S any tech we let go of is a way better option than kazeem. You want their info, ask. Or go to blackbishop. He seems to be doing his thing.

Pls in quote clarify ma? Are you saying am Kazeem

gbemsone:
how much is the semi synthetic oil

20W-50,
Castrol 8k
Hardex 5k
It depends sir on the product you choose to use.

gbemsone:
Boss,

I have a honda accord 2003,i need to do servicing on it what type of oil will u recommend

I forgot to ask the previous owner and presently his line not going thru

Please i need ur help

Boss first since you dont know the oil the previous owner was using then just go for semi synthetic oil sir.

glambo:
Please what dd you do

Scan it first.

Nowadays everybody has got something to say, but when they type you see the gibberish they punch out, like they forgot about sense.

Pls let's go back to the purpose of the forum.

P0016 TOYOTA - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor 'A'

P0016 Toyota Description

The Engine Control Module (ECM) controls the Oil Control Valve (OCV) to regulate the intake camshaft angle. As a result of the angle change, the engine timing is advance or slowpoke. Optimizing engine timing will help the engine improve torque and fuel economy, and the exhaust emissions decrease under overall driving conditions. The Variable Valve Timing (VVT) system includes the Oil Control Valve (OCV) and VVT controller. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control.

Possible Causes

▪︎ Dirty Oil
▪︎ Faulty Variable Valve Timing (VVT) sensor
▪︎ Variable Valve Timing (VVT) sensor circuit is open or shorted
▪︎ Variable Valve Timing (VVT) sensor poor electrical connection
▪︎ Faulty Engine Control Module (ECM)

Possible Symptoms

¤ Loss or Lack of Power.
¤ Rough Idling
¤ And most importantly Check Engine Light.

Possible Solutions

Change the engine oil, and rescan if not change the Variable Valve Timing Sensor. But before changing check the wiring.

B-Automobile Nigeria Limited
08055347947

P0016 TOYOTA - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor 'A'

P0016 Toyota Description

The Engine Control Module (ECM) controls the Oil Control Valve (OCV) to regulate the intake camshaft angle. As a result of the angle change, the engine timing is advance or retard. Optimizing engine timing will help the engine improve torque and fuel economy, and the exhaust emissions decrease under overall driving conditions. The Variable Valve Timing (VVT) system includes the Oil Control Valve (OCV) and VVT controller. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control.

Possible Causes

▪︎ Dirty Oil
▪︎ Faulty Variable Valve Timing (VVT) sensor
▪︎ Variable Valve Timing (VVT) sensor circuit is open or shorted
▪︎ Variable Valve Timing (VVT) sensor poor electrical connection
▪︎ Faulty Engine Control Module (ECM)

Possible Symptoms

¤ Loss or Lack of Power.
¤ Rough Idling
¤ And most importantly Check Engine Light.

Possible Solutions

Change the engine oil, and rescan if not change the Variable Valve Timing Sensor. But before changing check the wiring.

B-Automobile Nigeria Limited
08055347947

Hybrid600:
CC:
dru23

Honda DW-1 original

nwizu042:
Wetin I no go see today.. got a trip, pick up was Allan balogun off agungi road. Got there o. Next thing a big speaker was loaded in my back seat.. I just de look them. Then some other electronics in the boot.. when he was ready , I just kindly informed him that to addo road is 3k5 he laughed and said why na,Shei no b app we go use..?. this time na my turn to laugh..
I just tell am make he call him guys to offload.. na riders I de pick. No b kabu kabu be this...
Mtscheew...

I love this bro

izzou:
[color=royalblue]Be gone, for thy anointing has been taken away from thee

For thou hast begun to dwell with the daughters of Africa lane, the maidservants of Adeola Hopewell, even the sisters of Wumengo

Thy bishoprick has thou lost, and thou shalt no longer stand in the gap for thy brethren.

[/color]

Why has thou misconstruct my name?

mosesbola:
I asked them to charge me to court...

I was later released to go...

Someone need to be bold in this Lagos

Wow I just have to go back to understand where you are coming from. Those guys are toothless and barbaric.

I was to deliver a customer's car to him last week saturday, so I have to take 3md then link clinic road to face Ajah, toward the end of clinic road to link yaba, there is one dysfunctional traffic light there, a car was in front of me who waited for some folks crossing, immediately those guys successfully navigated their way across the road the vehicle in front of me moved which I followed suit.

Out of no where they just jumped in front me like say them don see prey. Within me I just laff say you go buy market wey no be your own now now. All the drama I no open door nor do I look concerned, the more they talk, the more I dey match my pedal dey move. When they see say I no send and am not ready to yield na dem comot my front.

In a nutshell for an instance you need to be bold and face them gallantly. Until proven guilty, you will remain innocent. Na just fear and I dont want them to delay me dey kill people