₦airaland Forum

And then there was 1.


Sadly the Nissan xterra came back with brake binding issues after the front wheels became so hot, there was an over flow of brake fluid from container, it droped on the exhaust and there was fire on the right wheel

We will check caliper pistons for stiffness, master cylinder for blockage, and abs pump for malfunction.

After pics engine wash accord 07

Hyundai sonata


Washed ready good to go.


When washing the engine cover the engine Ecu it's in the engine bay and exposed! (Koreans wan set me up) cover with a bag or remove b4 washing.

Prado 2012

Idle relearn procedure.

Followed all the procedures in the book, and rpm was still high (after throttle body service).


Took out the battery terminal for 1min, returned it back and the "olodo" learned!

Washed and ready to go.

Accord V6

Fluid sensor old and new(toks)

Saw a nasty tear on the front left brake lines.

Recommended change.


Note, to replace sensor, you must drain transmission fluid.

Honda accord 2006 (E0D) V6

Transmission fault

P0713 (transmission fluid temp circuit High)

Also there's a also a solenoid that had to be replaced (owners instructions), bolt was worn by previous technician.


To get to the fluid temp sensor jack front left wheel up, remove engine mounts in that area.

lomomike:
2.7L i4 used in hilux, highlander and some others. I bet this might be a manual transmission truck.
Buying truck and deleting the gas 'guzzling' eh. Erm actually, its okay acceleration wise.

It is very automatic

EagleScribes:
Thanks bro.

Oya Gazzuzz please show yourself o. My condition has been transferred to you. Pls help my emergency situation.

Thanks

08023251039 08033910382.

Accord 2007

Suspension parts assembled

Special wash on engine and suspension area.

There was a lot of grease on the suspension so a thorough cleaning was done


The after pics will be in the morning.

Prado 2012

Tyre pressure check (cold)

Front 29psi

Rear 32 (loaded) 29(unloaded)

Unfortunately all tyres were pumped to 40psi

Some people have this belief that if it is an suv it can be pumped to as high as 50psi

Tyre pressure set back to factory specs

Prado 2012

Vehicle is at 49k km so sparkplugs will not be changed.

Throttle body cleaning in pics below, please do not use hand or any tool to open butterfly, turn ignition on, have someone press throttle pedal, then spray carb cleaner and use dry rag to wipe while throttle is open.. when done peform idle re-learn procedure.

Toyota landcruiser Prado 2012 I4 engine

Work to be done.

Oil change, sparkplug cleaning, throttlebody cleaning tyre rotation/tyre pressure check.

adanny01:
25 miles so far, no CEL.

I sued to have a faulty O2 sensor that would cover 1200km without any codes

adanny01:
Guys, my car is at it again.

I had engine mount problems which led to my replacing the rear and the left engine mounts this afternoon. There was tight space to remove the bad rear mount. The mechanic had to move it repeatedly pushing stuff out of the way. Engine harness passes around there to the ECU.

All repairs finished with good result and even took it to car wash 300m away for only external wash. I left the car wash and 500m away CEL came on with D light flashing and N light staying lit. I parked, scanned and got P0705 same code from beginning of this thread. I checked to see if they pushed out any electrical connector especially one that leads to Park/neutral position switch but did find any. I cleared the cel hoping my little trouble shoot would hv accidentally solved the problem. I got the cel the next 500m. It still drives good and shifts well too. The cel keeps coming back after few minutes of driving.

I dont know if i should investigate the ECU for water like last time or what? The problem isnt exactly like before with this one less DTC's and less errors diaplayed at the instrument panel. The coincidence with all the activity around the engine harness gives me concern.

Re-adjust park neutral switch, if it does not work have it replaced.

It's on front right side near the wheel.

https://ww2.justanswer.com/uploads/rmldaytona/2012-03-24_225304_1.gif

All this winchy pickin

[quote author=jektony post=36132072][/quote]Screeching squealing could be the serpentine belt, try and adjust it.

Please stop using seahorse.

fkj950ax:
Where is your Workshop?

#3 Awe street, off Haruna street by alhaji Haruna bus stop , college rd ifako (ogba) 08023251039

mayor2013:

Mayor my man how market?

qunleajayi:
Dear Gazzus, u didnt respond to my request nau...

Your engine has a loss in compression.

Timing might be off too, but the fact that plugs are wet with water is badddd for the nation.

https://ww2.justanswer.com/uploads/indytech/2010-11-09_164014_max2.png

One thing you should understand is the paint marks on the chain should be usedto set timing.

Good luck sir.

chukel:
. my oga, are u serious. can it be bent back without breaking.

Look for a mallet and a good metal surface.

Also look for a hollow pipe of almost same diameter, when you nack am well e go pass thru with ease.

kunletexs:
PEOPLE IN THE HOUSE,

I want to buy a Honda EOD, but it has over heating issue, do I still buy it and is it a major issue.

What could be the cause of it and about how much could I prepare to repair it.

Professionals in the house, please advice.

Buy the car, subtract the cost of engine and labour, handling and logistics.

lomomike:
Check your dashboard light knob and turn it to the brightest if it doesn't work, check your fuses.

He could also give it a good slap!

If it works then there's a partial contact somwhere.

chukel:
yea, i saw the pads chopping from that upper side. the disc almost burnt my finger. thanks. that small bolt no de the whole of bayelsa o.

As e bend, bend am back

igbsam:
Hi guys, my Honda Accord does something that pisses me off.

First of all, it does this delay start. Whenever i try to turn on the engine, it wont do that, i will have to do it more than 2-4 times before it turns on.

Secondly, when it starts at times, the throttle will refuse to respond or rev. I will have to turn it off and then turn it on again, and when i try to rev it, it will respond or sometimes wont. I'll have to keep turning it on and off until it responds and then will move.

What could be the cause of this ? Mechanics are just saying all kinds of stuffs that i don't understand.

Scan but seems like and engine ecm error.

Could also be a tps error.

For a fix 08023251039 lagos

abbeYhart:
Nice job you are doing Gazzuzz..Seems that was the toyota sienna I saw at the gate of your auto workshop yesterday morning when I came to drop my car..Well done bro

Dass IT!! almost complete.

chukel:
this is exactly what i am suffering now. changed my brake pads 2 months ago as a preventive measure. afterwards i started hearing some clunking sound, grinding sound (only once in the morning when pulling out and applying brakes) then brake drag, and increased fuel consumption. then i started hearing some intermittent squeaky sound all from the same rear passenger tire. went back, we dismantled the caliper, greased the components and coupled back. symptoms lessened, then appeared with greater intensity. i came back from church on sunday, raised the car on jack and discovered tyre couldnt spin on its own (except with so much force from me). removed tyre, dismantled caliper and behold, upper caliper bolt was well bent. unfortunately couldnt get it in bayelsa. will be sourcing for it in PH tomorrow. gazzuz, is there any greater problem this might have caused to any other component?

Uneven wear on the brakepads.

Heat might have made the o rings in the caliper and piston weak. (not too likely)

Siena lower control arms down.

Now if you ever want to buy any part that has a bushing, always go with a long screwdriver, stick it in the center and tilt sideways. our brothers in the toks market like using superglue to hide cracks on bushings and paint over it, this test will catch any fraudulent part dealer.

Old and new control arms with bushings in pic below.

GAZZUZZ:
Going for a drive test on the mazda 6

Wonderful vehicle to drive

Speed demon!!!! chai! Need to get me 1 of these toys.

Meanwhile I will not be doing a customary engine wash since it's a misfire I'm trying to solve. So I'll just be doing a drycleaning.

Going for a drive test on the mazda 6

Wonderful vehicle to drive

Toyota sienna 1999

Suspension work.

Parts to be replaced.

Lower control arm

And shock absorbers.

Mazda6 2006 I4

Primary error, cylinder misfire on cylinder 1.


Sparkplugs will be replaced, injectors serviced, intake checked for leaks.

Will continue with the accord later tonight.


Next.

2011 hyundai sonata 2.4 liter GDI. Was towed to our office.

Not cranking.

Installed another battery and car started, allowed to run for 30mins and car refused to crank.

Battery was tested in another vehicle and cranks fine.

Primary fault is starter motor.

Vehicle was also scanned comprehensively and it had Evap codes (powertrain), and steering angle sensor with the anti skid warning on.

We will start by removing the starter motor whic is under the intake manifold.