₦airaland Forum

Picture 11: Addition of pull-up resistors and switching transistors.

Picture 10: Soldering of ADCs and optocoupler.

Picture 8: Mounting of IC sockets for microcontroller, ADCs and optocoupler.

Picture 6: Addition of voltage regulators and heatsink (solder side).

Picture 4: Creation of the power section (solder side).

Hi, in this thread, I will be showing pictorially the steps involved in the making of an oven control circuit board using a dot veroboard.
I am aware the modern trend in circuit board making is the use of Printed Circuit Board (PCB). However, this project was done for fun to demonstrate that a good and presentable circuit board can be created using rudimentary, affordable and readily accessible tools.


Picture 1: The beginning: ‘Virgin’ board with only connectors mounted.

Sweet.

Please tell your panelbeater to gum that rubber above the passenger side headlight to position.

I've experienced this before. It was caused by a throttle return spring that removed in motion.

The car just went to full throttle as I approached a roundabout. Luckily, the road was not as busy as it usually is at that time. I pressed the brake pedal as the car accelerates rapidly on, the car failed to stop but was just vibrating as I tried moving towards the shoulder of the road. I put the gear in neutral and the brake was able to stop the car as the engine roared loudly. I thereafter turned off the engine and corrected the fault.

It was a scary experience.

greggng:
Thank you for that observation. I didn't even bother to respond. It is what you call your child ,he or she will answer. To me this car is a machine..,,to him is a taxi....but what matters is how the owner perceive what he has. GOD BLESS EVERYONE

Your maturity is exceptional.

greggng:
You are very correct. In have changed that tire now you just read my mind. Will remove the sticker now. I don't even know who placed it. I packed somewhere and I suspect someone placed it. It doesn't add any value

I think it's too late now that painting has been done unless you plan to replace it with a cool badge.

greggng:
Back at the painter shop to put finishing touches to the car headlight etc

Great job sir. I admire people who go all out for quality!

Just curious here, why didn't you remove that sticker beside the V6 logo?
Also, that different front rim is reducing the beauty of your car.

Why won't the car go into neutral?

What type of Total oil did you use for the oil change?

The mid region looks crooked to me.

We also wish to applaud the Captain for exhibiting the highest safety standards and handling the situation professionally.

How can you say that the captain exhibited the highest safety standard?

Sunnah1:
#YourMumuContinue

#OurMumuDonTay

Long overdue.

It helps to restart the car if your engine stalls in motion without the need to come to a complete stop.

I don't think I have. Though it is often said that some thoughts or dreams are God's way of speaking to us, with how busy my mind is and the randomness of my dreams, I don't know how to hand pick some as divine.

Disclaimer: This applies to English speaking people only for some reason which the OP owes no one.

Remote serpentine belt. Start the engine briefly to confirm the sound is not coming from it & spin other individual components in normal direction of travel by hand to verify which is the culprit.
I'm still suspecting the power steering pump.

You mean ugliest.

autojosh:
I would top it if the brake pads are not worn out, not due for change or temporarily before fixing the issue. Note: The most important thing is to determine the cause of the shortage and decide if and when it has to be fixed.

Ok. Thanks

autojosh:
Sure, you have to top it after replacing the brake pads.

Okay. But what of before replacing the pads?

Adefemiaderoju1:
I hope after his efforts the babe won't turn him down

That will be so sad.

You need a 'boot' of moral after undertaking the most rigorous part of the task?

The way people take this proposal thing is ridiculous. You guys have been in this relationship for a while na.