somehow:


My sheet are from Johnytech.

Please can you share contact of the supplier

Thanks

mufutau55:


I have always use Johnytec and have recommended them to several people here

Do you have a contact that can supply and install this Johnytec?

Thanks I await your reply.

michlins:
pay me and I will do it for you in Lagos. Two weeks from start to finish.

But first,why do you need 40ft tank stand. What's the height of your building

The building can’t be more than 12m including roof
It is 3 floors.

Can you drop a competitive quote ?

Thanks

KolaShangOne:


Personally I had a nasty leak issue with it about 4 years ago. Hajj Mufutau55 knew about it. Since then, I only do longspan and steptiles except client can pay for Tower Aluminum.

Tower as of today for long span
0.45 - 3,937
0.55 - 5,382

Only for the deeper pockets

Good day house,

After much deliberation a tank stanchion has been decided.

My welder quoted for a 40ft stand and the price sent shockwaves down my spine.

Please help look at the quote, I believe it can be achieved for less. And I know @michlins isn’t based in lagos, I would have contacted him for the job.

How do we book?
Happy new year sir... will you be available for a site visit to take physical measurements

Thanks

Dennis3D:
We have now installed the sheets of this project.
We used Aluminum long span.55 guage for a budget of 1.3m for (sheets, accessories and installation)

Happy new year bros !! More projects in 2022 by Gods Grace.

Quick question about the colour of this roof, doesn’t black absorb more heat into the space, I understand the most likely POP will be used for the ceiling?

Also I’m at the roofing stage of my project as well, 1st thing on my list to do this year. If you don’t mind can you share contact of the supplier of the long span , I have about 265sqm to roof.

Thanks

Dubemcapital1:



Sharp sand is 7 buckets, gum sand is 3 buckets. So total of 10 buckets for one bag of cement.

Thanks a lot I will use this mix and showcase results

Dennis3D:
Some magnificent photos of properties here so it will give you a taste of what we are about doing here.

I’m loving these cantilevered buildings.

Better cantilever na money kill am.

Well done Dennis3D ...

Edit:
Do you have a painter you can recommend for a living room make over

Dubemcapital1:
Let's take a closer look

Well done.

I’m at the plastering stage for a project, what mix did you use to achieve this smoothness ?

Thanks

Thanks Oga Spyder. Kindly help with cost of the woody tan per sqm

spyder880:
Still more to choose from......

Hi sir ,

Do you offer consultation services, I’m project managing a site and the client wants to purchase paint for the building. We are at lintel level.

How long do your paints last in storage ?

Lagos, lekki is the location

Thanks

michlins:
this level of rust under two years is basically cause of inferior choice of materials.

As it is now, I will suggest that you cut off the area that has been affected,use angle bar to frame it all round and then spray anti-rust paint first before proceeding further to paint it completely.

These paints goes for about 4500 each cup and the volume is just 1.5l. There are other brands like Sharon and Dulux depending on your funds

Okay noted.
I will contact you if the person wants to fix/replace the gate.

Thanks

michlins:
it can be salvaged. You have to replace the pipes at the bottom part with slopping pan. That way it doesn't retain water at all. If you're doing a gate in and around Lagos, kindly ensure that you don't use pipes at the bottom. Where if it's important to use pipes, cover it with angle iron of at least 4mm thick. That way, the effects of rusting will be delayed as much as possible.


See what I did here, instead of welding directly on the pipe, I got another stronger material to take the heat

@michlins thank for your input. I believe the cause for this level of rust just after 2 years of installation is the salt in the air in that area. In fact I observed other using an iron frame and wood to construct their gate in that area.

Can nothing be done to prevent rust?

Do you have any experience using anti rust paint/spray on your gate fabs?

I also noticed these hand railings didn’t rust. Pics:

In other news. I was asked to give advice on a gate that has been damaged due to the nature of the surrounding environment.

I gave my honest opinion to replace the gate, but there might be better solutions from experts here. What say ye?

Pics:

Chibaba247:
Pls good people, I am at the roofing stage of my building, I want to know if it will be OK using a steptile or metcoppo or any other type aside a stone coated sheet, as I am embarking on a flat roof design.
Thanks and God bless u all

I will love to hear the opinions of the house on this.

My opinion on the roof design or style should complement the house design. Meaning a modern contemporary house might have a flat roof

Dennis3D:


thank you sir for always coming through.
I know Oga Hajj will soon come with his seat soon.

In this estate they don't allow anything like semi Detached houses. It must be fully Detached or nothing.

With time, I will be sharing some houses being built here. They are really massive.

Starting with the one am sharing below...

That’s interesting, the kind of estate I like. Rules and regulations must be followed.

That means they would even allow luxury flats?

Following this development. Class is in session

Dennis3D:


We used 295 bags of Cement.
2.5 tons of 16mm
3.5 tons of 12mm
1 Ton of 10mm
4 roles of binding wire
2.5 Trips of granite of 30 Tons each.
2.5 Trips of Sharp Sand or 30 Tons each.
Marine board 80 Pieces
1x12x12 - 150 pieces
4 Bags of Nail.
And so on.
Bamboo lengths 380 Pieces

We casted 90% of work on the casting day and finished the remaining 10% of the next day.

Wow this is a really big job.

How much did you pay the casting crew? I’m looking for a “caster man” for an up coming job

GAZZUZZ:
Stolen catalytic converter? Burnt out catalyst?

No issues.

This device will clear your pending P0420 or P0430 codes on your vehicle.

It is a specially designed O2 sensor spacer with catalytic converter inside.

No need buying catalytic converters any more, just install this device and code will not come back.

As usual our products come with money back guarantees (beat that)

What the product looks like.


https://www.youtube.com/watch?v=QVZ54HIKbkc

Sample instalation

Rx330/350 2004-2009 Bank1 instalation


https://www.youtube.com/watch?v=fcwTD-m4cpg



https://www.youtube.com/watch?v=SsRVYdQnka4



https://www.youtube.com/watch?v=Gj1yMvcwoPA



https://www.youtube.com/watch?v=_JqW0RCWz8c





Nation wide delivery.

Contact 08033910382

Shop location, ogba lagos

WhatsApp Message Gazzuzz Autos on WhatsApp. https:///message/CNJWRUBB775EK1

Good morning do you have this solution for 2009 Honda Accord?

Dennis3D:
Second Decking concrete work day
Our routine is Beams and Staircase First.
Our vibrator machine is equally and routinely at work with us.

Nice work. More grease to your elbow.

I’m very interested in the casting aspect(cost) of this slab. Do you mind sharing cost breakdown of the labor? And where you able to finish before dark (6/7pm)

Thanks

KolaShangOne:


It's achievable. That's one of the ways we can achieve balance and control greedy capitalist middlemen / retailers.

But Nigeria is a free market".

If only we can cap cement at say 3200. If you sell more, they lock up your shop!

If we have a govt controlled pricinh on granite supply. Iron supply, etc..

Let Govt. also control percentages paid to Engineers / contractors..

It will add a bit of stability to every industry.

I’m not a fan of government intervention is business because it’s requires a responsible government for it to work and most are not especially not Nigeria. People will still take advantage of the system e.g Fuel subsidy, Fertilizer.

I bought 12.5kg gas for 9,000 yesterday. A 100% increase from 1 year ago.

Nigerians which way forward.

twinskenny:
For your electrical supplies
Pipes
Knock out boxes
Havels distribution board
Switches and socket
General electrical fittings

Location is not a barrier but trust me quality delivery await you.

I have some quote on electrical supplies, can you help with prices location is Igboefon I will handle delivery cost

1. 3 by 3 eight packets
2. 3 by 6 six packets
3. 20mm malebush three packets
4. 20mm coupler four packets
5. 25mm malebush one packet
6. 25mm coupler two packets

Thanks

n3xt:


Very far but I can ask one of my guys to bring it down next week.

Please note, they might have to remove the stones too.

Okay. Removing the stone will definitely require more hands involved.

Okay then I look forward to next week. Kindly drop your contact so I can text you.

Thank you very much.

n3xt:


I have mine. I can lend you if your location is not too far from me.

https://instagram.com/p/CSA9gYLqQmE/

I watched the video, exactly the end result I’m hoping to achieve.

Sure I would appreciate your gesture. Location needed is Maroko area in lekki.

Do let me know if this is not too far from you.

Very nice.

Pressure washing might be the best option. I’m sure it might be more efficient that pouring chemicals and brushing manually.

@next did you rent or buy the pressure washing machine.

n3xt:


I did one recently in one of my big bro’s house. We removed the interlock stones, pressure wash them and lay them back.

I’ll see if I can share video of the cleanings process.

Good morning house,

What can one use to get rid of green algae on interlocking floors and fence? The look is becoming unsightly. Thanks

Dubemcapital1:


As at the time we fabricated the steel doors, it was 67,000 each for 4ft x 7ft door (spacification: 1.2mm or complete18 gauge flat sheet for the door frame and 1.5mm or 16 gauge flat sheet for the door panel)

And

45,000 each for 3ft x 7ft doors ( same spacification)

Thanks boss, info will be helpful when the time comes