₦airaland Forum

Welcome, Guest: Join Nairaland / LOGIN! / Trending / Recent / New
Stats: 1,927,493 members, 3,968,085 topics. Date: Thursday, 14 December 2017 at 05:13 AM

T's Garage (landrover And Cars) - Car Talk (3) - Nairaland

Nairaland Forum / Nairaland / General / Car Talk / T's Garage (landrover And Cars) (24634 Views)

Question Of The Day.. Whose Garage Is This? / Countries And Cars They Produce / Photos: This Is Someone's Garage In Abuja (1) (2) (3) (4)

(0) (1) (2) (3) (4) (5) (6) (7) (8) (9) ... (12) (Reply) (Go Down)

Re: T's Garage (landrover And Cars) by erico2k2(m): 12:18am On Jul 12, 2016
LeJeun3:





Please send me a mail, with parts you have purchased and we can see whats good. Chat me up on whtsapp if possible.

WEll here goes
parts Im getting
LHD dashboard,complete, upper and under
Steering rack
Pedal box
Door cards
Ac lines
wiper motor assembly
Brake lines
Wiring looms.

1 Like 1 Share

Re: T's Garage (landrover And Cars) by LeJeun3: 9:30pm On Jul 14, 2016
erico2k2:

WEll here goes
parts Im getting
LHD dashboard,complete, upper and under
Steering rack
Pedal box
Door cards
Ac lines
wiper motor assembly
Brake lines
Wiring looms.



Nice.... Chat me up on whatsapp!


Re: T's Garage (landrover And Cars) by LeJeun3: 9:16am On Jul 23, 2016




Will be right back................ with many stories.
Re: T's Garage (landrover And Cars) by LeJeun3: 5:08am On Jul 28, 2016


Don't know where to start!

Land Rovers are wonderful cars, complex enough so avoid electrical alterations such as Trackers and Third Party anti theft devices, you really could be sorry!



Re: T's Garage (landrover And Cars) by LeJeun3: 5:10am On Jul 28, 2016


Valve Seal replacement for an Audi A4



1 Share

Re: T's Garage (landrover And Cars) by LeJeun3: 4:18am On Aug 06, 2016
Been out of network coverage but I am back.....
Re: T's Garage (landrover And Cars) by LeJeun3: 4:21am On Aug 06, 2016



Original Equipment Manufacturers put in a lot of money to get these parts to perform.


Buy them and see your vehicle perform as well


1 Share

Re: T's Garage (landrover And Cars) by LeJeun3: 8:37am On Aug 14, 2016


So its been a while I made a post... Been on the road a lot.


Re: T's Garage (landrover And Cars) by LeJeun3: 8:40am On Aug 14, 2016


"Fuel cap missing" message flashes on your dashboard and you rush to check the cap to be sure the attendant closed it properly.

Its well closed, then you start up again and alas, not only is it still there but you have the CEL light on....


Re: T's Garage (landrover And Cars) by LeJeun3: 10:06am On Aug 14, 2016


"HDC Fault"

This is very common on LR3 04-09, Range Rover Sports, and Discovery II.



Simply change you battery grin

Thank me Later.




Re: T's Garage (landrover And Cars) by mrintelligent(m): 1:09pm On Aug 15, 2016
Please I need an experts in converting cars from RHD to LHD. There is this RHD Peugeot 407 that was sent from UK and needed to be converted to LHD.

Please, where and How much will the conversion cost me?

Thanks
Re: T's Garage (landrover And Cars) by LeJeun3: 6:36am On Aug 16, 2016
mrintelligent:
Please I need an experts in converting cars from RHD to LHD. There is this RHD Peugeot 407 that was sent from UK and needed to be converted to LHD.

Please, where and How much will the conversion cost me?

Thanks




If you are in Lagos, visit the popular Ladipo market....


I don't do Conversions!

Re: T's Garage (landrover And Cars) by LeJeun3: 8:04pm On Aug 16, 2016




To get rid of the "fuel cap missing" message a lot has to be done.

The item in red is the culprit after a fuel cap has been changed.


1 Share

Re: T's Garage (landrover And Cars) by LeJeun3: 8:15pm On Aug 16, 2016



As simple as it looks this isn't a very easy DIY, you really must be ready to get your hands dirty and your back too wink

Re: T's Garage (landrover And Cars) by komekn(m): 1:54pm On Aug 26, 2016
Lejuen, I respect your advice and realise there are considerations unique to Nigeria I probably am ignorant about.

Seeing you working on an A4 confirms what I already presumed you are not parochially restricted in your applicable knowledge and experience to strictly one brand.

I want to buy an Audi Q7 TDI to use in Nigeria however the L3/4 my other option is considerably more robust off road. However, I believe in fact I know, the build quality of the Audi is considerably better than the L3/4. The long term outcomes for the Audi Q7 could mean better resilience, reliability and therefore toughness. However, all of this will amount to nothing without good maintenance from a good conversant mechanic like you.

I prefer the Audi, better drive much more compliant ride on the bumpy roads, I will be doing about 5000 miles a year if that from 2/3 trips to Nigeria and I will be driving Lagos to Delta (Warri-PH) but mainly resident in Lekki.

What’s your advice please Sir ? Not worried about TDI engine issues in Nigeria with you around.
Re: T's Garage (landrover And Cars) by LeJeun3: 6:34pm On Sep 01, 2016
komekn:
Lejuen, I respect your advice and realise there are considerations unique to Nigeria I probably am ignorant about.

Seeing you working on an A4 confirms what I already presumed you are not parochially restricted in your applicable knowledge and experience to strictly one brand.

I want to buy an Audi Q7 TDI to use in Nigeria however the L3/4 my other option is considerably more robust off road. However, I believe in fact I know, the build quality of the Audi is considerably better than the L3/4. The long term outcomes for the Audi Q7 could mean better resilience, reliability and therefore toughness. However, all of this will amount to nothing without good maintenance from a good conversant mechanic like you.

I prefer the Audi, better drive much more compliant ride on the bumpy roads, I will be doing about 5000 miles a year if that from 2/3 trips to Nigeria and I will be driving Lagos to Delta (Warri-PH) but mainly resident in Lekki.

What’s your advice please Sir ? Not worried about TDI engine issues in Nigeria with you around.



Thanks for the compliments.
You have said it all. The Audi will give you that ride comfort you desire and fuel economy too. You could go out to get it, since you won't be doing much off roaring. Point to note is that the Q7 won't take flooding as lightly as the LR3 /4 would take it..


Re: T's Garage (landrover And Cars) by LeJeun3: 6:35pm On Sep 01, 2016





Octane Booster now in stock......
Re: T's Garage (landrover And Cars) by LeJeun3: 7:36pm On Sep 06, 2016


When your car starts overheating there are several possible causes for this, in as much as many don't believe it a scan and proper diagnosis would reveal the cause.


I was a with a client yesterday who had already spent a fortune on trying to resolve his overheating problem, he had changed Clutch fan, Water pump, washed radiator yet his Range Rover Sport would still overheat between his house and the closest round about.

I got a call and waded into the matter, and low and behold wrong diagnosis was involved.

Need help with Overheating ?? Read on...........

Re: T's Garage (landrover And Cars) by LeJeun3: 7:57pm On Sep 06, 2016


P0480 is a general OBDII trouble code that refers to a malfunction within the cooling fan control circuit. This code comes in P0481 and P0482 codes.

What the P0480 code means

P0480 means that the cooling fan 1 control circuit has a malfunction. The vehicles ECU has tried to control the cooling fan 1 and it has failed to operate or a fault was detected. The ECU then triggers a Check Engine Light to illuminate on the dashboard (many cars already have the CEL illuminated so they don't get to notice this).

What causes the P0480 code?

Faulty cooling fan 1
Poor electrical connection in the fan circuit
Failed fan control relay has failed
Failed coolant temperature sensor
Faulty AC pressure switch
VSS not operating properly

What are the symptoms of the P0480 code?

The most obvious symptom will be the Check Engine Light on the dashboard being illuminated.

The more serious side effect is that the vehicle's temperature may rise enough to overheat the vehicle if the fan is not operating.

How does a mechanic diagnose the P0480 code?

Uses a scan tool and checks for any codes stored in the ECU

Notes the freeze frame data that shows the coolant temp, RPM, vehicle speed, and etc. from when the code was set

Clears all of the codes

Takes the vehicle on a test drive and attempts to duplicate the conditions from the freeze frame data

Performs a visual inspection of the the fan system, checks carefully for fan operation and looks for damaged or worn wiring

Uses the scan tool to look at the datastream and confirms that the VSS sensor has proper readings, and that the coolant temperature sensor is reading accurately

Uses a relay tester to test the fan control relay or switches the relay with a good relay to test

Checks for proper operation of the AC pressure switch and that it is reading within specifications

Common mistakes when diagnosing the P0480 code

Mistakes are made when step by step diagnosis is not performed or steps are skipped entirely. There are many systems that may be responsible for the P0480 code and if they are overlooked the fan may be replaced when it was really the coolant temp sensor causing the fans not to operate.

How serious is the P0480 code?

P0480 can become serious if the vehicle is allowed to overheat. If the vehicle overheats it can cause engine damage or the engine to fail entirely.

If the P0480 code is found and the fans are not operating then the vehicle should not be driven.

What repairs can fix the P0480 code?

Replacing the VSS sensor
Replacing the engine coolant temp sensor ( On the Range Rover, a new Thermostat )
Repairing or replacing of the fan wiring harness
Replacing cooling fan 1
Repairing electrical connection issues
Replacing AC pressure switch
Replacing the fan control relay




1 Share

Re: T's Garage (landrover And Cars) by LeJeun3: 1:11am On Sep 07, 2016



2008 Range Rover Sport for Sale.......... Neat and clean 5Million!!!!
Re: T's Garage (landrover And Cars) by LeJeun3: 10:03pm On Sep 11, 2016

Diagnosis of overheating in a V8 Petrol Land Rover

So you say your Land Rover overheats? In this article we’re going to cover the steps to diagnose a variety of overheating problems. Some are trivial, and others will require a complete engine overhaul. Overheating is a problem whose repair cost can range from zero to what seems like infinity.
Land Rover V8 engines are mostly aluminum with some steel and iron components. Aluminum engines are very susceptible to damage from overheating. Before we begin I need to warn you — if you haven’t been warned already — not to ever drive a Land Rover with the temp gauge in the red, not even a short distance. Driving an overheated Rover half a mile down the highway could cost you an engine.

Let’s begin our diagnosis by opening the hood and having a look. If the truck is steaming hot, leave it and return when it’s cooled off. Otherwise there’s a risk of scalding yourself. Is the fan belt in place? Is the fan tight when you wiggle it? A loose fan is a sign of a failed water pump or fan clutch.

On some Rover models it is possible to route the serpentine belt wrong, so the water pump spins backward. If your overheating follows a belt replacement check the routing.

When you look at the fan make sure none of the plastic blades are damaged. If you see any cracks or chips or broken blades, replace the fan. We have seen damaged fans explode with enough force to go right through the hood. Not only will a fan with a broken blade explode… it will also cause a heavy vibration that can ruin a good water pump in less than 100 miles.

Is there any coolant in the radiator or expansion tank? A slow leak can allow coolant to leak out until one day there’s not enough and the truck overheats. A fast leak can cause the coolant to blow out in a matter of seconds. Look for a blown hose or cracked radiator or expansion tank. Slow leaks often leave a trace of sediment where the coolant emerges and evaporates.

Slow leakage is a particular problem with the newer Discoveries, because they don’t have a warning light. And, being British, they leak.



Re: T's Garage (landrover And Cars) by LeJeun3: 10:05pm On Sep 11, 2016

The radiator must be filled with clean coolant of the correct type. Filthy old coolant should be flushed before proceeding with diagnosis. If the coolant is contaminated with oil you need to find the reason before proceeding. The most common cause in a Land Rover is leakage from the oil cooler into the radiator. Occasionally oil will mix with the coolant as a result of an internal engine problem but that’s rare.

Putting the wrong coolant in a late model Rover can cause overheating problems. Putting the traditional green coolant into a vehicle made for the orange Dex-Cool can result in sediment formation, and that sediment can clog the cooling system.

There are three coolants used in Land Rover products.

RTC7601 is traditional green ethylene glycol coolant. It’s used in all older Land Rover models. All Series Land Rovers, all US market Defenders, all Range Rover Classics, and all P38 Range Rovers up to 1999 use this coolant. If you have a 1999 Range Rover and you’re not sure which coolant to use… if the last digits of your VIN are YA444891 or lower, your truck uses ethylene glycol. If your VIN is higher, you should use Dex-Cool.

With the arrival of the Bosch engine management system in the Discovery II and the 1999-½ Range Rover Land Rover changed to Dex-Cool, otherwise known as OAT coolant. Land Rover stocks that coolant under part number LRN 2279. The Freelander models also use OAT.

The 2003 and newer Range Rovers use BMW’s Glysantin G48 coolant. It’s distinctive because it’s bright blue in color. Land Rover sell that as LRNG48.

If your Rover uses Dex-Cool you have to be sure to keep the system full all the time. Running the engine when low on coolant will cause damaging sediments to form.

At this point I think we should have a word on the subject of “full.” When we say “make sure the cooling system is full” what does that mean, exactly? You should make sure the radiator is full to the top, there is no air in the system, and the coolant level in the expansion tank is where it should be, looking at the level indicator molded into the tank. Air in the system can cause overheating and it can be a real problem to remove it on some trucks. Many shops use a vacuum pump to remove all the air from the cooling system before filling to avoid this situation.

If you overfill the system it will spit the excess coolant onto the ground. Don’t mistake coolant expelled from the overflow line at the expansion tank for a leak.

Anyway, once your vehicle is full of clean correct coolant we can proceed. If it does not overheat anymore after flushing your, radiator is probably mostly clogged. A like-new radiator has enough cooling capacity that the temperature gauge won’t budge from the midpoint, even on a hot summer day. If your Rover improves with flushing that means its radiator is pretty clogged and you just made it a bit better. I’d suggest you remove it and have it re-cored or replaced. If that solves your problem, congratulations, you’re done.

If your truck still overheats you’ll need to keep going. The next step should be a test to determine if your engine is really overheating. I suggest measuring the temperature of the engine with an infrared thermometer. Measure the upper radiator hose where it exits the motor as that’s near where the sender for the gauge is located. The top of the white area on your temperature gauge should be about 220 degrees on the thermometer. If your gauge is at the top and the infrared thermometer is showing 190-200 degrees you’ve got a gauge problem, not an overheating problem. If you have a real overheating problem, read on…

When the truck is warmed up feel the hoses… are they hard or soft? Soft hoses indicate a system that’s not building up pressure. Check and find the cause of pressure leakage. Some possibilities are a bad cap, leaking hoses, or cracked expansion tanks.

If the hoses are really hard that is a sign of excessive cooling system pressures. Excessive pressures often result from combustion gases leaking into the coolant passages and over-pressurizing the system.

If you find that, you should check for combustion gases in the coolant. There are two ways to do this. Auto parts jobbers sell a kit consisting of a glass tube and test liquid. You place the tube over the radiator filler hole and run the vehicle. If the liquid changes color there are combustion gases escaping through the coolant.
Another method of testing is to sniff the radiator filler with an exhaust gas analyzer. The analyzer is more likely to pick up small leaks that won’t color the test liquid.
If your truck passes both the above tests you probably do not have internal engine problems.

Re: T's Garage (landrover And Cars) by LeJeun3: 10:08pm On Sep 11, 2016

Overheating under load, NO combustion gas in coolant


Overheating under load may be a sign that your radiator is clogged. The tubes in the radiator become lined with hard deposits as the radiator ages. These deposits will significantly reduce the radiator’s ability to remove heat from the coolant.
I suggest removing the radiator and having it checked for clogging. When you remove the radiator, look for debris blocking its surface. Also check for debris blocking the AC condenser and oil coolers. A leak from an oil cooler can leave a film of oil that collects dust like a magnet, leading to complete air blockage of large parts of the radiator. If air flow is restricted the vehicle will overheat under load.

You should also check the engine driven fan if you have one. It has a viscous coupling that allows it to freewheel in cold weather and be tightly coupled in hot weather. If the fan freewheels on a hot day it won’t cool adequately.

The electric fans are controlled by temperature and/or AC operation. In some cases the fans are turned on whenever the air conditioner is running. In other cases the fans come on when a threshold engine temperature is reached. In either case the electric fans need to work to keep the motor cool in summer.

In a few cases we have seen overheating caused by separation of the water pump impeller from the shaft. This is more of an issue with BMW and Jaguar cars that use plastic impellers pressed onto a steel shaft. The only way to check this is by removing the pump.

Here are some other causes of overheating that you should check:

If the radiator cap is bad (not holding pressure) or if the cooling system has other air leaks the cooling system will boil and overheat.
A stuck thermostat will cause overheating all the time (stuck closed) or cold running all the time (stuck open.)
A Rover may overheat in hot weather if the fan shroud is missing or damaged.
A clogged catalytic converter will cause substantial heat buildup under the hood and can lead to overheating and serious loss of power.

Re: T's Garage (landrover And Cars) by LeJeun3: 10:11pm On Sep 11, 2016


Overheating under load, combustion gas in coolant


If you have combustion gas in the coolant your motor has one of three problems:
One of the head gaskets has failed;
One of the heads, a cylinder liner, or the block has cracked;
Or one of the cylinder liners in the block has moved.
In some cases you may see steam and smell a sweet odor from the exhaust. That’s a sure sign of coolant entering the combustion chamber and exiting via the tailpipe. Much of the time, though, the leak goes the other way — combustion gases going into the coolant, and there may be no visible evidence.
The first step in finding out what went wrong is to remove the cylinder heads. When you do this you’ll have a chance to check for sludge under the valve covers and intake. If you have a lot of sludge I suggest engine removal and a complete teardown and cleaning. If the engine is sludge-free you may or may not be able to repair it in the car, depending upon what you find.

The head gaskets should be examined carefully. You may see tracks where gas leaked from the combustion chamber to a coolant gallery. Tiny cranks in the ring that seals the combustion chamber are a sign of pre-ignition. You can check for localized overheating by measuring the gasket thickness. A spot that ran hot will have a thinner gasket – something you can pick up with comparative micrometer measurements. An experienced machinist will be able to spot many head gasket failures.

Re: T's Garage (landrover And Cars) by LeJeun3: 10:14pm On Sep 11, 2016


Failed head gaskets are the most common reason for combustion gases getting into the coolant. But it’s important to understand that you can’t fix a head gasket failure by just slapping on a new gasket and bolting it together. Doing so will usually result in a repeat failure at some future date. You need to find and fix the underlying problem. That means repairing mating surfaces that are not perfectly flat, repairing the cause of the pre-ignition, or fixing the cause of localized overheating. Localized overheating is often a result of injector or ignition troubles on one cylinder and it can be difficult to find but it’s an insidious killer. Left alone it will overheat a single cylinder until the liner loosens in the block and even greater damage ensues.

The heads are checked for flatness with a straightedge. Aluminum heads should be flat within .002 inch. They are checked for cracks by applying air pressure while bolted to a jig, or by application of liquid crack detection chemicals that highlight cracks under black light. Cracked heads can usually be repaired by welding. Warped heads can be surfaced on a milling machine or specialized cutter. Rover heads should not be surfaced more than five thousandths of an inch, because the compression ratio increases as the heads are shaved.

If coolant was entering the combustion chamber you will see one or more cylinders scoured spotlessly clean by the steam. Pay particular attention to those cylinders if you see them because they are the ones that have failed. If you see this, or if you see milky oil in the engine, you should pull the oil pan and check for lower end damage because coolant is getting into the oil. Coolant mixed with oil will damage bearings.

The steel cylinder liners are pressed into the block and milled flush with the top. If you see any liners that have moved downward that’s s a sure sign of failure. If you do not see any signs of movement in the liners you must make a decision to remove and test the block or take your chances and refit the heads.

The block is tested by bolting plates over the cylinder head mating surfaces and applying pressure to the oil and coolant galleries to check for leaks. Leakage indicates a loose liner or the presence of a crack.

The block can also be checked for flatness on the cylinder head mating surface. As with the head, the surface must be flat within .002 inch. I have seen a number of instances where shops replaced head gaskets, experienced a subsequent failure, and assumed the block had a bad liner when in fact the deck surface was warped. It’s important to figure out what went wrong if you are to have a lasting repair.

A block with a dropped liner can be repaired by removing the liner and pressing in a slightly larger replacement that is flanged at the top so it can’t move. A block whose cylinder head mating surfaces have warped can be surfaced in a process called decking. If the cylinder head mating surface has warped, there is a good chance the crankshaft bore is warped also. In that case, the block will need the main bearing journals line bored after it’s been decked.

The traditional method of fixing liner and deck problems in Rovers was to replace the engine block. With the increased costs for new blocks repair is now becoming a better option.

I hope the tips in the article above will allow you to diagnose your overheating trouble. In the case of engines with combustion gases in the coolant there is usually some other problem that led to the internal engine failure. Before you count the job done you should find that problem and fix it.

Finding those problems — things that cause internal engine failures - will be the subject of a future article.

Re: T's Garage (landrover And Cars) by LeJeun3: 10:19pm On Sep 11, 2016
LeJeun3:


Failed head gaskets are the most common reason for combustion gases getting into the coolant. But it’s important to understand that you can’t fix a head gasket failure by just slapping on a new gasket and bolting it together. Doing so will usually result in a repeat failure at some future date. You need to find and fix the underlying problem. That means repairing mating surfaces that are not perfectly flat, repairing the cause of the pre-ignition, or fixing the cause of localized overheating. Localized overheating is often a result of injector or ignition troubles on one cylinder and it can be difficult to find but it’s an insidious killer. Left alone it will overheat a single cylinder until the liner loosens in the block and even greater damage ensues.

The heads are checked for flatness with a straightedge. Aluminum heads should be flat within .002 inch. They are checked for cracks by applying air pressure while bolted to a jig, or by application of liquid crack detection chemicals that highlight cracks under black light. Cracked heads can usually be repaired by welding. Warped heads can be surfaced on a milling machine or specialized cutter. Rover heads should not be surfaced more than five thousandths of an inch, because the compression ratio increases as the heads are shaved.

If coolant was entering the combustion chamber you will see one or more cylinders scoured spotlessly clean by the steam. Pay particular attention to those cylinders if you see them because they are the ones that have failed. If you see this, or if you see milky oil in the engine, you should pull the oil pan and check for lower end damage because coolant is getting into the oil. Coolant mixed with oil will damage bearings.

The steel cylinder liners are pressed into the block and milled flush with the top. If you see any liners that have moved downward that’s s a sure sign of failure. If you do not see any signs of movement in the liners you must make a decision to remove and test the block or take your chances and refit the heads.

The block is tested by bolting plates over the cylinder head mating surfaces and applying pressure to the oil and coolant galleries to check for leaks. Leakage indicates a loose liner or the presence of a crack.

The block can also be checked for flatness on the cylinder head mating surface. As with the head, the surface must be flat within .002 inch. I have seen a number of instances where shops replaced head gaskets, experienced a subsequent failure, and assumed the block had a bad liner when in fact the deck surface was warped. It’s important to figure out what went wrong if you are to have a lasting repair.

A block with a dropped liner can be repaired by removing the liner and pressing in a slightly larger replacement that is flanged at the top so it can’t move. A block whose cylinder head mating surfaces have warped can be surfaced in a process called decking. If the cylinder head mating surface has warped, there is a good chance the crankshaft bore is warped also. In that case, the block will need the main bearing journals line bored after it’s been decked.

The traditional method of fixing liner and deck problems in Rovers was to replace the engine block. With the increased costs for new blocks repair is now becoming a better option.

I hope the tips in the article above will allow you to diagnose your overheating trouble. In the case of engines with combustion gases in the coolant there is usually some other problem that led to the internal engine failure. Before you count the job done you should find that problem and fix it.

Finding those problems — things that cause internal engine failures - will be the subject of a future article.



This the hard part really ................
Re: T's Garage (landrover And Cars) by LeJeun3: 10:50pm On Sep 11, 2016
LeJeun3:
Complete......

LeJeun3:

2008 Range Rover Sport for Sale.......... Neat and clean 5Million!!!!
Re: T's Garage (landrover And Cars) by instantex: 4:19am On Sep 16, 2016
Where is your workshop in Lagos?
Re: T's Garage (landrover And Cars) by LeJeun3: 6:57am On Sep 16, 2016
instantex:
Where is your workshop in Lagos?



Ebutte Metta
Call or chat me up....

Re: T's Garage (landrover And Cars) by LeJeun3: 7:07pm On Sep 17, 2016

Found a great car today............. a 2012 Range Rover Autobiography with just 18K Miles on it!!! grin grin


Re: T's Garage (landrover And Cars) by LeJeun3: 9:11pm On Sep 20, 2016


Ever wondered why your alarm goes after parking your car a while??



Changed the locks and same thing keeps happening??


Hood sensor has always been the cause and is relatively simple fix if you know what you looking for.... wink

Re: T's Garage (landrover And Cars) by LeJeun3: 12:08am On Sep 21, 2016



Range Rover Computers have a back door like every computer....


An infotainment system diagnostic menu, a bit more complicated to access:


a) Go to the system's Main Menu by pressing the RH hard button under the touchscreen.
b) Press the upper center portion of the touchscreen - about an inch to the right of the letter "U" in the "Main Menu" header - for a good 7 to 8 seconds (nothing visible or audible will happen at this point), then release the touchscreen.
c) Press and briefly hold the LH HARD button under the monitor. After a couple of seconds, a Diag PIN entry window should pop up over the main menu.
d) Enter diag code 753 and press OK, the diagnostics main menu will appear. Proceed at your own risk from there.

(0) (1) (2) (3) (4) (5) (6) (7) (8) (9) ... (12) (Reply)

I Mistakenly Bought A Non-drivable Car / Meet The Awesome Car “wallys Iris” -made In Africa / Help! V.I.S Officials Just Meted An Injustice On Me (pics)

(Go Up)

Sections: politics (1) business autos (1) jobs (1) career education (1) romance computers phones travel sports fashion health
religion celebs tv-movies music-radio literature webmasters programming techmarket

Links: (0) (1) (2) (3) (4) (5) (6) (7) (8) (9)

Nairaland - Copyright © 2005 - 2017 Oluwaseun Osewa. All rights reserved. See How To Advertise. 245
Disclaimer: Every Nairaland member is solely responsible for anything that he/she posts or uploads on Nairaland.