₦airaland Forum

@all the killer freq on intel7/10 is true. It locked down a friends decoder last month. What i did was to do factory reset and after that deleted the killer freq from the decoder.
Do'nt forget to turn off OTA of your 69x. Very important.

@iykmann, happy birthday and many happy returns in blessings and good health

@teeworld
if yr box shows lnbf even when the lnb cable is unpluged, that is a sign that the ic inside the decoder that powers lnb is bad. You need a professional to help you with it. Best bet is to take to strong office for repairs

@aka tenero
It is obvious that your dish has shifted, Retrack again and make sure your crtv 12600v3250 is btw 88-90%. All will be fine.

@samw
Astra 2b 12600v3250
W3a 12728h30000
Sirus 12605v29950
Nss7 11555v30000

Happy Birthday George D. The Good Lord continue to keep and prosper you. Cheersssssss!!!!!!!!!!

@philcool
Your 4652 is mpeg2 and can be used for infinity but note that you will receive their mpeg2 channels only while the mpeg4 channels will give you audio only.

@samw
you can use 63x for any satellite. But being an mpeg2 receiver, you can only receive mpeg 2 channels and not mpeg 4 channels. If you have mpeg4 receiver like 69x you will receive both mpeg 2&4 channels.

Lcf now on w7@36e on freq 12435 h 23437

if in lagos, check shop B270 @ alaba satellite section

@adeexy, i will be visiting a senior friend this weekend. Are you motorising it?

@Peroluv
Deeperlife is available 24/7 on intelsat7/10 freq 12682 h 26657

@ameboperoo
Living faith tv-ro on intelsat 902c: 4048 v 3425

@mjay, me too; i need a copy ooo
I will give a call on sunday sir.

@adeex, thank your the pix.
I hope your daarbox is rocking
@all
You can add 1 more lnb to make 3in1 set up

yes those daarsat decoders that show daar when booting are already locked for daarsat. though you can find a way around it.

candymann, motorising a dish is as simple as abc. Check the childboard i have thread on it. and am ready to answer your questions 24/7

@bode4real
What is your signal quality of w4/7 on your 53x. If it is not high enough, that could affect reception on 69x. They do not boost sgnal the same way. Ensure your signal on 53x is 97%, then connect your cable to the 69x i believe the signal will come up green

@bode4real
Delete all frequencies and Connect your cable, then blindscan

@sunsat, 4653x rreceives infinity for now. All their channels are mpeg2 except one. Perhaps when you tracked this morning, infinity was off air remember they are still test transmitting. You can check again

@ameboporo
Check shop B270@ alaba satellite market
@ojosoft
Chances of Getting an original 4653x now is slim. Why not go for 4663x instead, price should be btw 7-8k and ensure you buy from accredited mytv dealer, that way you eliminate the possibility of getting fake

@Lov4sat
In ph tracking w3a can be tricky
From my experience in PH track w3a to the left of dstv and not right when standing behind the dish.
You can use sirus 4 on 12605v 29950 as refrence. When you hit green, input 12728v30000 For w3a and lower dish a bit to the left.
Good luck

@Badaru1
what hd decoder will you recommend apart from STRONG decoder that is FTA friendly in terms of 1. Price 2. Software- patch- support via USB flash 3. Blind scan function

@All,
Winners chapel tv- TVRO on intelsat 902@62' E 4048 v 3425.

These satellites have footprint covering nigeria, remember this was the way we discovered astra2b and sirus4.
NSS 5@20' WEST
INTELSAT801@29.5'WEST
INTELSAT25@31.5'WEST
GALAXY11@32'EAST
INTELSAT802@33'EAST
GALAXY26@50.8'EAST
INTELSAT706@54'EAST

Cont'd
4. Determine your east and west
5. Get frequencies of satellites- you can use www.lyngsat.com or www.flysat.com to get list of frequencies. You can also get list of satellites recievable in your location on www.dishpointer.com

STEP TO MOTORISING
1. Track the farthest eastern satellite and mark it on the pole, eg in naija track intelsat 7/10
2. Track a western satellite eg Nss7 and mark it on the pole
3. Track a satellite on the top of the arc eg sirus4.

VERY IMPORTANT
To make the dish track the arc, you must set the declination angle also known as dish tilt. This can be done simply by tracking your due south satellite. In naija use sirus 4@4.8' E to set your declination or dish tilt.
6.When you've manually done the above, then attach your jack.
Pls follow manufacturers insruction when mounting your jack.
7. Connect your jack to the positioner as instructed in the manual. You will need a 4way cable, computer networking cable can be used. Pls pay attention to wire colour so that you do not destroy your jack due to wrong wiring.
8. Now move the dish and start to track your satellites.
GOOD LUCK

Motorising large dishes start with the pole stand.
Ensure the pole/pipe is straight up i.e at angle 90. You may have to use angle meter or bricklayers' plumbline.
2. If your dish is pan or net. You have to follow the setup intructions in the manual to ensure your dish is properly assembled.
3.get your jack and positioner handy

Lets talk about motorising big dishes here.
Questions related to this topic should be posted here for professional answers.

@Bertos, yours may be original since you downloaded strong's original patch and it's still working

@Bertos, get path from _www.wizkid.persiangig.com and your decoder will work with the code again. But pls ensure your is original otherwise it could be fried.

its possible. So let us know how

YES, hitv card works on 53x. You don't need to patch. All you need is the working TPs of Hitv

@shola and all, the conversion of scart to rf is simple and can be very cheap. With N500 u a done. Step 1: buy the scart(pls note output, not input ) to av cable, it is about N200. Step2: buy av to rf converter, it is like a small modem and uses electricity, cost about N200-N300. step 3:connect scart end of the cable to the decoder and av end to the av-rf converter, connect the rf from the converter to the tv and search tv for the signal , the converter broadcast on uhf or vhf depending on type. REMEMBER TO PLUG BOTH THE DECODER AND AV-RF CONVERTER TO POWER BEFORE SEARCHING FOR SIGNAL ON TV.

@olabisi75,
if your signal on crtv and others are not high enough say about 97% on 53x stb, your lmtv (dvb server) may not come up. So check your signal level as you might need to adjust your dish or lnb skew to increase your signal.