₦airaland Forum

Kaduna rangers kit looks better than this

Fadomero:
I don't know why whenever I see this Muslims something scary just go through my mind I always remember osama

Your mind needs to be cleansed with jik hypo happic combined

Apelex:
My toyota corolla 2009.misfires. When ever the vehicle is very hot. I loose engine performance.
I cant accelerate.
Went to a mechanic. I was told to change the fuel pump.i did. I also changed four spark plugs. But Problem still persist.
I did a scan and got this codes.
P00171
P0015
P0017
P0102
P0113
P0351
P0352
P0353
P0354
P0420
Its so bad that the engine light blinks and the vehicle turns off sometimes
Please what do i need to do to get the Vehicle running smooth again??

I would advice you don't throw parts, have a competent mech diagnose it. From these fault codes, my hypothesis is a low power feed problem that may be caused by a very high resistance somewhere in the circuit. Pls don't rely upon my hypothesis, have it diagnosed.

Have the car scanned and diagnosed by a competent mech, alot culprit here.

tppzzy01:
Pls I need urgent help right now on my Honda accord 02, my kazeem help me to service my nozzle yesterday and today my gear is sludging. It will take high firing for the gear to select to gear 2 and more fire to gear 3 and will not select again. I took it back to him, he said I should take it to my rewire, that he did not go to the area of gear. Of which, I just change my gear oil some few weeks ago... Right now, the rewire self don't know what is the problem. He is saying he will re service the nozzle . Pls any help or suggestion.

Scan the car first

Xtrachidi:
Best wishes to you.

please, my Honda Acura Car is recently giving me a challenge such that the odometer will come to zero and quench immediately I put the gear.

When the car starts, the odometer will be at the normal level or revolution but immediately I apply the gear, it will go down completely and off the engine. If I manage to move the car, the engine suddenly goes off immediately I apply the brake to reduce the acceleration completely especially on a hold up or a pot hole.

A mechanic suggested to change the six plugs with platinum NGK which I did but that could not remedy the situation.

Please, what exactly should I do as I am in need of an exact solution to avoid changing whole lots of parts without solution.
Please, I need your help!

First go for a scan. Pls don't throw parts, it needs intensive diagnosis.

zoedicus:
Eyah, I pity him. After all those years serving and gathering knowledge, he wasn't sure if he's burning in hell or getting virgins in heaven. So much uncertainty, that's what you get when you miss the way, truth and the life. HE said he's going to prepare a place for us, not like this one crying because he has no place in eternity.

Allah be praised.

Don't you know how to read or what??

tensazangetsu20:
Nice so you didn't become an apprentice or anything.

Someone with solid background in electrical/electronics Engineering doesn't need to be an apprentice, because he was one a student to lecturers. That alone is enough.

thebigkendo:
Funny..yesterday I was doing my YouTube rounds and came across a video of DiagnoseDan diagnosing a BMW with a scope


https://www.youtube.com/watch?v=VF3s0uZ7ok0

I really learnt alot from this guy, I've watched most of his videos.

autologic:
Likei It depend on how far u want to go in the industry ,I deal mostly with the few luxury brand like benz , Audi etc ,they challenge my knowledge and pay for my time and will hopefully take on the EV like Tesla and the likes very soon . Corolla is not my thing cos I am bore with the blandness
If want to remain a corolla technician ,this thread is not for you

Boss I want you to be my mentor, I'm a student, I also repair cars as well, and I love to face challenging problems, especially with CANBUS systems.

Oscilloscope gives precise and accurate values of variables with respect to time. With that you can precisely know when a particular event occurs and how it affects other functions. If you really know how to use it.

Your power steering pump is bad swap it out.

successfem:
I have same issue with my steering. When I drive While turtling it's relatively soft but when I slow down with the brake pedal it gradually becomes stiff. I also notice little drops on the ground every morning too

ML350 bigger, classier, rugged and a sweet ride

Go for a scan first, alot of things can cause it not to accelerate, faulty throttle body, faulty throttle pedal, loss of powers and grounds and much more variables.

stitcheD:
Guys please help me out. My corolla suddenly stops accelerating as if it has lost connection with the accelerator pedal. The engine does not stop running. My mechanic is at his wits end. Please help a brother out.
Gazzuz and co.

If you are in Lagos, go to Ajegunle, or Clegg in Ojuelegba.

Pls don't throw parts have it diagnosed, it might be clogged fuel line, injectors, filter.

TheMan17:
Thank you bro. I had to go underneatg myself and i think i found the relay but after changing the relay. Still same thing. I am thinking of changing the fuel pump...see where that takes me but i will visit a specialist first. Like you said. Its one of the relays.

I really appreciate your time trygo. I really do.

It's a parasitic drain issue, have a good rewire check it.

danielconstant:
Good morning ikenna351. Please my Peugeot 406 2001 manual is having issue... If I leave the battery connected to the terminal through the night it drains down but if I disconnect it.. It don't. .What is the cause and also a possible solution

The ones initially, observed is a misfire code for all cylinders. P0505 is an Idle Air Control code, your car might have a rough idle or stall, just have it checked,it is located in the throttle body, it might be clogged. The ones you observed after maybe has a result of faulty or clogged MAF sensor deceiving the PCM to run the engine lean, or faulty O2 sensor not feeding back correctly, there by continuously running the engine lean. Alot of variables not surfacing in the fault codes might need to be checked as well.

ifeolu002:
Good Morning Guru,

I just got a 2004 Matrix about a week about. The first scan code i observed was P0505
After my mechanic check the did servicing of the car with Mobil 1 synthetic , More code came out and the car engine performance is not smooth even after servicing the nozzle.
Below are the codes observed initially;
P0505
P0301
P0302
P0303
P0304

This also came out later in pending fault
P0171
P0133
P0451

Please what might be the issue for this numerous codes all at what
Your detailed reply will be appreciated.

A broken timing chain does not necessarily mean you have to change engine, so far it has not damaged it, you just have to replace it and reset the timing.

mumayo:
please I need expert opinion. my Mitsubishi Chariot (GDI) suddenly stopped after a sound while on motion. called my mechanic who informed me that the Timing belt has cut and that I have to buy a new engine. please is this in line because the price he's quoting for a tokunbo engine don weak me

Hello boss, pls where and how can I get a PC based oscilloscope. Thanks in advance sir

Since you use something to hold it down it may be as a result of a bad switch.

Kokomo:
Hi Gazzuzz, nurey, deportivo, motorguru what can be the cause of hand brake light coming on by itself when driving ... most time i have to press it down again... even use handkership to hold it down

State your car details

Kokomo:
Hi Gazzuzz, nurey, deportivo, motorguru what can be the cause of hand brake light coming on by itself when driving ... most time i have to press it down again... even use handkership to hold it down

Internally

ebhohon:
I have washed it twice by the spray Painter but has not worked.

Google will explain better than I would, I hope you understand

Loujay:
Thanks for your timely response. Please how do I reset the oil life?

Since you have replace the oil, you car is not in danger anymore, you just need to reset the oil life to switch it off.

Loujay:
My Lexus ES330 continues to show me the “MAINT REQD“ warning light on the dashboard even when I have replaced the engine oil completely though recently. Please I really need your advice on what to do for the message to go off the dashboard or those this potend any danger for my car engine? Kindly advise a brother Sir.

Hello boss GAZZUZZ where can I get a PC based oscilloscope here in Nigeria, thanks boss.

If you can remove them and wash with detergent, and get a new bulbs, if the ones there are not ok

ebhohon:
How do I resolve the challenge of my inability to see far at night with 1997 toyota camry headlight

Go for a scan first, as for the oil level, the oil switch might be bad.

osy77:
Goodevening Guru's and enthusiasts...so I just bought a c300 2015 benz some 3-4 weeks ago...serviced it with Mobil 1 and only a couple of days back "check oil at next refuel" pops up after about 10-20minutes drive...I click ok and it disappears only to reappear on the next drive.


Today I realized the car jerked from D4-D5 shifts. Biko una blother need help b4 these Abuja Mechanics finish me biko

Go for a scan.

Henrygreat212:
Please House good evening... I drive Lexus 350 2010 model.. but after parking the car for 3 weeks without warning or driving it, my car just developed fault. It just just started showing check engine, Check 4WD sign, then even with hard throttling it won't speed pass someone walking... Urgent response on what I should do next and how/where to resolve this issue will be highly appreciated.. Thanks House

From the details you have given it seem your car has issues entering closed loop, which might cause it to guzzle fuel fast. It needs extensive diagnosis by an expert.

[ quote author=neyop85 post=82598564]Good evening all, I changed the complete shaft of my Honda DC. During test driving I noticed it was jerking while changing gears and it will jerk before getting into drive or reverse.
I kept on changing gears while static and little by little the issue disappeared.
Was the transmission system trying to calibrate itself with d new shaft? Is it normal for it to do that after changing a complete drive shaft?[/quote]the valvebody of the transmission has been messed with.

[The valvebody has been messed with. quote author=neyop85 post=82598564]Good evening all, I changed the complete shaft of my Honda DC. During test driving I noticed it was jerking while changing gears and it will jerk before getting into drive or reverse.
I kept on changing gears while static and little by little the issue disappeared.
Was the transmission system trying to calibrate itself with d new shaft? Is it normal for it to do that after changing a complete drive shaft?[/quote]